Black Box VOE212 User manual

CUSTOMER

SUPPORT

INFORMATION

Order toll-free in the U.S. 24 hours, 7A.M. Monday to midnight Friday: 877-877-BBOX

FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746

Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web site: www.blackbox.com • E-mail: [email protected]

Multiport Digital VoIP Router

Important

This is a Class A device and is intended for use in a light industrial environment. It is not intended nor

approved for use in an industrial or residential environment.

Approval

This device is approved for connection to the public ISDN telecommunication network, over BRI/S0-

ISDN interfaces.

JUNE 2007

VOE211

VOE212

MULTIPORT DIGITAL VOIP ROUTER

TRADEMARKS USED IN THIS MANUAL

All applied-for and registered trademarks are the property of their respective owners.

•

The VOE210 contains no user serviceable parts. The

equipment shall be returned to Black Box for repairs,

or repaired by qualiﬁed service personnel.

•

Mains Voltage: Do not open the case the power cord

is attached. The external power adaptor shall be a

listed limited power source that incorporates a dis-

connect device and shall be positioned within easy

reach of the operator. The mains outlet shall be

within 10 feet (3 meters) of the device, shall be eas-

ily accessible, and protected by a circuit breaker.

•

For AC powered units, ensure that the power cable

used meets all applicable standards for the country

in which it is to be installed, and that it is connected

to a wall outlet which has earth ground.

•

Hazardous network voltages are present in WAN

ports regardless of whether power to the VOE210 is

ON or OFF. To avoid electric shock, use caution when

near WAN ports. when detaching the cables, detach

the end away from the VOE210 ﬁrst.

•

Do not work on the system or connect or disconnect

cables during periods of lightning activity.

In accordance with the requirements of council directive 2002/96/EC on Waste of

Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you separate

this product from other waste and scrap and deliver to the WEEE collection system in

your country for recycling.

WARNING

MULTIPORT DIGITAL VOIP ROUTER

1. Power up the VOE210

1. Connect theVOE210 to the mains (AC) power source with the power cable.

2. When the

Power

LED stops blinking and remains lit, the VOE210 is ready

to conﬁgure.

MULTIPORT DIGITAL VOIP ROUTER

2. Connect the VOE210 to your local network

Figure 1.

Connecting the VOE210 to the PC

1. Connect the PC’s Ethernet port to

LAN (ETH

0/1)

port of the VOE210. The

VOE210 Series is equipped withAuto-MDX Ethernet ports, so you can use

straight-through Ethernet cables for host or hub/switch connections. (See

Figure 1.)

2. The VOE210 comes with a built-in DHCP server to simplify conﬁguration.

Therefore, to automatically conﬁgure the PC for IP connectivity to the

VOE210, conﬁgure the laptop PC for DHCP. TheVOE210 will provide the

PC with an IP address.

3. Check the connection to theVOE210 by executing the

ping

command from

the PC command window as follows:

ping 192.168.1.1

The interconnecting cables shall be acceptable for external use and shall be rated for

the proper application with respect to voltage, current, anticipated temperature, ﬂam-

mability, and mechanical serviceability.

CAUTION

Straight-through wired cable

LAN (ETH 0/1)

Laptop PC

MULTIPORT DIGITAL VOIP ROUTER

3. Conﬁguring the desired IP address

3.1 Factory-default IP settings

The factory default conﬁguration for the Ethernet interface IP addresses and net-

masks are listed in

table 1

. Both Ethernet interfaces are activated upon power-up.

LAN interface

ETH 0/1 (LAN)

provides a default DHCP server. The WAN inter-

face uses DHCP client to get the IP address and netmask automatically from the

service provider.

If these addresses match with those of your network, go to section “Connecting

the VOE210 to the network” on page 7. Otherwise, continue with the following

sections to change the addresses and network masks.

3.2 Login

1. To access the VOE210, start the Telnet application on your PC. Type the

default IP address into the address ﬁeld:

192.168.1.1

. Accessing your

VOE210 via a Telnet session displays the login screen. Type the factory

default login:

administrator

and leave the password empty. Press the

Enter

key after the password prompt.

administrator

password:<Enter>

192.168.1.1>

2. After you log in, your VOE210 will be running in operator execution mode

(indicated by > character in the command line prompt). To enter conﬁgura-

tion mode, use the commands

enable

and

conﬁgure

192.168.1.1>

enable

192.168.1.1#

configure

192.168.1.1(cfg)#

Table 1:

Factory default IP address and network mask conﬁguration

Item IP Addresss Network Mask

WAN interface Ethernet 0

(ETH 0/0) DHCP DHCP

LAN interface Ethernet 1

(ETH 0/1) 192.168.1.1 255.255.255.0

DHCP server address range

(LAN) 192.168.1.10-

192.168.1.19 255.255.255.0

MULTIPORT DIGITAL VOIP ROUTER

3.3 Changing the WAN IP address

1. To modify IP conﬁguration settings, you must enter

context IP

mode. Enter

the following command:

192.168.1.1(cfg)#

context ip router

192.168.1.1(ctx-ip)[router]#

2. Now you can set your IP address and network mask for the interface

ETH

0/0(WAN)

. In this example a network 172.16.1.0/24 is assumed. The IP

address in example is set to

172.16.1.99

. (You should set it to the IP address

that the network provider has given you.)

Note

The examples in this guide use a private IP network with the network

address

172.16.1.0/24

192.168.1.1(ctx-ip)[router]#

interface eth0

192.168.1.1(if-ip)[eth0]#

ipaddress 172.16.1.99 255.255.255.0

2002-10-29T00:09:40 : LOGINFO : Link down on interface eth0.

2002-10-29T00:09:40 : LOGINFO : Link up on interface eth0.

172.16.1.99(if-ip)[eth0]#

3. Copy this modiﬁed conﬁguration to your new start-up conﬁguration. This

will store your changes in non-volatile memory. On the next start-up the

system will initialize itself using the modiﬁed conﬁguration.

172.16.1.99 (if-ip)[eth0]#

copy running-config startup-config

172.16.1.99 (if-ip)[eth0]#

The VOE210 can now be connected to your network.

MULTIPORT DIGITAL VOIP ROUTER

4. Connecting the VOE210 to the network

In general, theVOE210 will connect to the network via theWAN (ETH 0/0) port.

This enables the VOE210 to offer routing services to the PC hosts on LAN (ETH

0/1) port. TheVOE210 Series provides an auto-MDX feature for both Ethernet

ports, so you can use a straight-through or cross-over cable to connect to a host or

a switch (see Figure 2)

Figure 2.

Connecting the VOE210 to the network

1. You can check the connection with the ping command from the VOE210 to

another host on the local LAN.

172.16.1.99(if-ip)[eth0]#ping <IP Address of the host>

Note

If the WAN address is

not

set to DHCP, to ping a device outside your

local LAN you must ﬁrst conﬁgure the default gateway.

The interconnecting cables shall be acceptable for external use and shall be rated for

the proper application with respect to voltage, current, anticipated temperature, ﬂam-

mability, and mechanical serviceability.

CAUTION

Straight-through wired

or crossover cable LAN (ETH 0/1)

LAN

WAN (ETH 0/0)

Network

MULTIPORT DIGITAL VOIP ROUTER

5. Loading the conﬁguration (optional)

Black Box provides a collection of conﬁguration templates on the CD-ROM

shipped with your VOE210 device, one of which may be similar enough to your

application that you can use it to speed up conﬁguring the VOE210. Simply

download the conﬁguration note that matches your application to your PC.Adapt

the conﬁguration as described in the conﬁguration note to your network (remem-

ber to modify the IP address) and copy the modiﬁed conﬁguration to a TFTP

server. The VOE210 can now load its conﬁguration from this server.

Note

If your application is unique and not covered by any of Black Box’s con-

ﬁguration templates, you can manually conﬁgure the VOE210 instead of

loading a conﬁguration ﬁle template.

In this example we assume anTFTP server resides on the host with the IP address

172.16.1.11 and the conﬁguration ﬁle named

VOE.cfg

resides in the root direc-

tory of the TFTP server.

172.16.1.99(if-ip)[eth0]#

copy tftp://172.16.1.11/VOE.cfg star-

tup-config

Download...100%

172.16.1.99(if-ip)[eth0]#

After you reboot the VOE210 the new startup conﬁguration will become active.

172.16.1.99(if-ip)[eth0]#

reload

Running configuration has been changed.

Do you want to copy the 'running-config' to the 'startup-con-

fig'?

Press 'yes' to store, 'no' to drop changes :

Press 'yes' to restart, 'no' to cancel :

yes

The system is going down

When you issue the reload command, the VOE210 will ask if you want to copy the

running conﬁguration to the startup conﬁguration. Since you just downloaded a con-

ﬁguration ﬁle to the startup conﬁguration you must answer this question with

Otherwise, the downloaded conﬁguration will be overwritten and lost!

IMPORTANT

MULTIPORT DIGITAL VOIP ROUTER

6. Additional Information

Refer to the

VOE210 Getting Started Guide

located on the CD-ROM shipped

with your VOE210 device and available online at

www.blackbox.com/manuals.

For detailed information about:

•

Installing, conﬁguring, operating, and troubleshooting.

•

Warranty, trademark & compliance

The CD-ROM also includes many freeware and shareware tools, including TFTP

servers, and Telnet clients.

MULTIPORT DIGITAL VOIP ROUTER

A. Compliance Information

A.1 Compliance

EMC:

•

FCC Part 15, ClassA

•

EN55022, Class A

•

EN55024

Safety:

•

UL60950-1/CSA C22.2 No. 60950-1

•

IEC/EN 60950-1

•

AS/NZS 60950-1

PSTN Regulatory Compliance:

•

TBR3

•

AS/ACIF S031

A.2 Radio and TV Interference

The VOE210 router generates and uses radio frequency energy, and if not

installed and used properly—that is, in strict accordance with the manufacturer’s

instructions—may cause interference to radio and television reception. The

VOE210 router have been tested and found to comply with the limits for a Class

B computing device in accordance with speciﬁcations in Subpart B of Part 15 of

FCC rules, which are designed to provide reasonable protection from such inter-

ference in a commercial installation. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If the VOE210 router does cause

interference to radio or television reception, which can be determined by discon-

necting the unit, the user is encouraged to try to correct the interference by one or

more of the following measures: moving the computing equipment away from

the receiver, re-orienting the receiving antenna and/or plugging the receiving

equipment into a different AC outlet (such that the computing equipment and

receiver are on different branches).

This manual suits for next models

Table of contents

Other Black Box Network Router manuals

Black Box

Black Box LPH1006A-R2 User manual

Black Box

Black Box LGB4005A User manual

Black Box

Black Box LB9007A-SC-R3 User manual

Black Box

Black Box LBS3041AE User manual

Black Box

Black Box LGB2008A-R2 User manual

Black Box

Black Box LW6001A User manual

Black Box

Black Box LGB624A User manual

Black Box

Black Box LB308A User manual

Black Box

Black Box COS-4P User manual

Black Box

Black Box LB9213A User manual

Black Box

Black Box LGB316A-R2 User manual

Black Box

Black Box LGH1006A User manual

Black Box

Black Box WRT750A User manual

Black Box

Black Box ME550A-35 User manual

Black Box

Black Box LDM-MR128 User manual

Black Box

Black Box Multiport Analog VoIP Gateway Router VOE231A User manual

Black Box

Black Box LPB1308A-R2 User manual

Black Box

Black Box LEH1008A User manual

Black Box

Black Box WRT-300BGN-R2 User manual

Black Box

Black Box LEH808 Series User manual

Black Box

Black Box LW6005A User manual

Black Box

Black Box LB9007A-ST-R3 User manual

Black Box

Black Box LGB1002A-R2 User manual

Black Box

Black Box Version 1.0 User manual

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

TP-Link

TP-Link TD-8817 QIG

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

Cisco

Cisco NCS 540 Hardware installation guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

Cisco

Cisco ASR 1000 Series Installation and configuration guide

EnGenius

EnGenius ESR-9710 quick start guide

Cisco

Cisco 805 Series Product overview