Bitstream ERIS-100 Instruction manual
Quick start manual, a detailed manual is on the enclosed CD or can be downloaded
from company's website www.bitstream.com.pl/en/
REV.
1.01
User Manual ERIS-100
2019.11.20
1/5
ERIS-100
Fiber opical converter - Ethernet 10/100/Mbps
.1 TOP VIEW OF THE DEVICE
1 2 3 4 5
Fig 1. Top panel of the device
Symbols designation:
1. PE –Ethernet port connector;
2. LNK/ACT, SD, FEF –Signalling LEDs;
3. FO –SFP optical port connector;
4. LP LNK, PWR –Signalling LEDs;
5. PWR –power connector;
.1.1 Signalling LEDs
1 2 3
Fig 2. Signalling LEDs
Designation of signaling diodes:
1 - LNK –indicator of correct connection on the optical port;
2 - SD –signal reception indicator on the optical port;
3 - FEF –Far End Fault –error signal reception indicator;
Quick start manual, a detailed manual is on the enclosed CD or can be downloaded
from company's website www.bitstream.com.pl/en/
REV.
1.01
User Manual ERIS-100
2019.11.20
2/5
Fig 3. Signalling LEDs
Designation of signaling diodes:
1. –LP LNK –signaling the correctness of connection of the remote device's electrical port;
2. –Power connection indication;
.1.2 Status of Ethernet electric interface signaling
The Ethernet port is equipped with two indicator lights.
green color - Signaling of correct connection, flashing during transmission
orange color - Signaling operation of the electrical link in 100Base-TX mode
.1.3 Connectors description
The front panel of the device has an RJ45 interface for the electrical interface
Ethernet, SFP optical interface slot, and power connector..
1 8
Fig 4. RJ-45 connector
The individual signals for RJ-45 connectors are shown in the table.
Connectors RJ-45 Ethernet 10/100Mbps
Pin number
Signal name
Description
1 (white/orange)
RXAn
Channel n transmitter
2 (orange)
RXBn
3 (white/green)
TXAn
Channel n receiver
6 (green)
TXBn
.1.4 Optical connectors
The device is equipped with an SFP module slot. The device supports 155Mbit/s SFP modules (MM,
SM, WDM, CWDM, DWDM, Copper). The range and type of connector depends on the type of SFP
inserted.
Quick start manual, a detailed manual is on the enclosed CD or can be downloaded
from company's website www.bitstream.com.pl/en/
REV.
1.01
User Manual ERIS-100
2019.11.20
3/5
As an example SFP for the device we propose the BTP-3103-L2CD model (155M, 20km, 1310 nm,
duplex, DDMI).
.2 DEVICE CONFIGURATION
On the side wall of the device there is an eight-position ON / OFF switch module which is used to
configure the converter.
Fig 5. Side view of the device - dip switch
The DIP SWITCH switch allows you to configure the following parameters.
Fig 6. Device configuration using microswitches
.3 POWER SUPPLY
–Voltage range 6-60V DC (the device can also be ordered in a 5V version via USB).
Quick start manual, a detailed manual is on the enclosed CD or can be downloaded
from company's website www.bitstream.com.pl/en/
REV.
1.01
User Manual ERIS-100
2019.11.20
4/5
–PoE++ version requires power supply of 52-57V DC to power the outdoor device
–Power consumption 55mA at 48V DC
–Voltage polarity - unrestricted
.4 POESUPPLY FOR PD DEVICES
With the switch No. 1 you can change the PoE mode on the RJ45 electrical port. By default, the
switch is set to OFF - Auto mode, so you can power external devices in the PoE ++ standard with
power up to 90W. Switching to ON position activates FORCE mode. In this mode, you can power
external devices without PoE standard up to 30W.
Switch no. 1 is not used in the device version without PoE.
ATTENTION!!! Setting the DIP-SWITCH No. 1 to the ON position (FORCE mode) in cases
where a device that does not support PoE is connected to the ERIS converter via UTP, may
damage the device port or in the worst case the whole device.
.5 FIRST START-UP
The ERIS-100 is ready to operate automatically when the power is connected. When the power
supply is properly connected, the power LED should flash.
.6 CONFORMITY TO STANDARDSAND RECOMMENDATIONS
The ERIS-100 device has been designed based on applicable standards and recommendations in
the field of data transmission, electromagnetic compatibility and safety of use.
.6.1 Electromagnetic compatibility
The device was designed pursuant to the standard EN 55022 class A, PN-EN-55024.
BITSTREAM devices are designated to functioning in closed premises.
Notice: This device is a class A device. In the residential environment may cause radio
frequency interference. In such cases, you can require the user to take appropriate measures.
.6.2 Safety
In respect to safety of service, BITSTREAM devices were designed and tested for operation
safety along with the EN 60950 standard.
Configuration and installation of the device should be executed by authorised persons
familiar with the service manual. The producer shall not be responsible for any occurrence that could
result from usage and installation that might not conform to this manual.
Quick start manual, a detailed manual is on the enclosed CD or can be downloaded
from company's website www.bitstream.com.pl/en/
REV.
1.01
User Manual ERIS-100
2019.11.20
5/5
.6.3 Data transmission
Functions of data transmission and parameters of communication interfaces of the device are
defined by the following standards and recommendations:
IEEE 802.3-2002 –Ethernet Interfaces 100/10Mbps
IEEE 802.3af/at –compliance of Ethernet interfaces with PoE/PoE+ standard
.7 PACKING COMPLETATION OF THE PRODUCT
1
ERIS-100 device
1 pcs.
2
User manual on CD
1 pcs.
3
Short user manual
1 pcs.
4
Declaration of confirmity
1 pcs.
5
Warranty Card
1 pcs.
6
Holder for DIN rail
1 pcs.
7
Holder for wall
1 pcs.
8
Power screw connector
1 pcs.
Table of contents
Other Bitstream Media Converter manuals
