birddog MINI User manual
Quick-start guide
Version 2.0
MINI
Firmware Update
This product has regular firmware updates to enable additional
features and functions, please ensure you update to the lastest
firmware by following the instructions in this guide.
bird-dog.tv/firmware
Please take time to ensure all items are incuded in your
BirdDog product package.
What’s in the box
Product Registration
Please register your BirdDog Mini on our website to ensure you
receive all the latest news and firmware updates via email.
You can register here - bird-dog.tv/register
1. LED Indicator
2. 1Gb Ethernet / Power over Ethernet
5. Audio Headset connector
6. DC Input (5-18v DC)
External connectors & features
3. HDMI Input
4. HDMI Output
1. Mini Main Unit
2. International Adapters
3. AC/DC Power Adapter
Powering Options
PoE Power over Ethernet (802.11af/at)
Mini can receive power and data through a single Ethernet cable.
Always use a certified 802.11af/at switch with minimum 12w port
power capacity.
Always use geniune BirdDog power adapters.
3rd party products can cause permanent damage.
Dc Power (strictly 5-18v)
Once a DC cable is connected the unit will
automatically power on.
Once PoE Ethernet cable is insered the unit will
automatically power on.
Booting up your BirdDog Mini
As soon as BirdDog Mini detects a power input signal the left hand
'power/fault' light will light up green.1
Typically the status will change after 10-20 seconds, at this point
the middle 'status' light will light up blue to indicate the second
stage of booting has begun.2
The final stage of booting will show the status light change to white
indicating the BirdDog is ready and able to be found on the
computer network.3
After initial boot up is complete your Mini unit will be visible as a
source on any NDI compatible devices on the SAME ethernet
subnet.
For further networking architecture instructions including routing
please consult either your system administrator or the support
page at bird-dog.tv
Determining video input
Valid video input
If BirdDog Mini detects a valid HDMI video input, the status LED
will change to blue.1This indicates that the source is detected and
the BirdDog is now streaming video over the NDI interface.
No Input
If the BirdDog Mini can not sync to a source or has no source
attached the status LED will display red.2This indicates that the
BirdDog Mini is operational, available on the network but not
detecting a valid source.
Please log into the BirdDog Mini web interface and change the
input settings to match your source device.
Tally light behaviour
Tally is used in productions for both talent and camera operators
to be aware which camera is being transmitted live to air (Program)
or being previewed with the intention of going live to air next
(Preview). BirdDog receives these signals from devices that
support Tally such as vision switchers and displays this information
on the internal screen.
If no destination device is receiving the NDI signal being genera-
ted by Mini in either PROGRAM or PREVIEW mode, Mini's Tally
light will not illuminate.1
If a destination device is receiving the NDI signal being generated
by Mini on the PREVIEW bus, the tally light will illuminate GREEN.2
If a destination device is receiving the NDI signal being generated
by Mini on the PROGRAM bus, the tally light will illuminate RED.3
Connecting a video source
If the video input format changes while BirdDog Mini is active, the
unit will automatically reconfigure its settings to accommodate the
change when set to 'AUTO' mode on the web configuration
interface. The process of reconfiguring the inputs takes approxima-
tely 3 seconds and is not recommended during a live production.
BirdDog Mini accepts HDMI video inputs, refer to the latest release
notes for confirmation of the current supported video rates and
resolutions.
Once your BirdDog Mini has booted up succesfully it will automati-
cally detect the incoming format and set everything up accordingly.
If you would like to manually configure your input, this can be done
via the web interface.
Accessing the web configuration console
After initial boot up is complete your BirdDog Mini unit will be
visible as a source on any NDI compatible devices on the SAME
ethernet subnet.
For further networking architecture instructions including routing
please consult either your system administrator or the support
page at bird-dog.tv
As BirdDog progresses through its boot-up sequence it will cycle
through various status modes as described in the section 'Booting
up your BirdDog Mini'.
Once the boot cycle is complete the status LED will illuminate
blue. At this point the Web configuration console is available,
please type the following URL into your web browser:
http://birddog-xxxxx.local
Where xxxxx is the last 5 digits of
the serial number on the sticker
of your device (lower case).
Default password: birddog
Your computer may require some prerequisite software installed to
enter the above URL successfully.
Please ensure Apple Bonjour is installed on your computer, the
installation package for this is available at:
bird-dog.tv/firmware
Alternative access to the Web configuration console
As an alternative to directly typing in the URL of your BirdDog unit,
BirdDog Finder is a beta (pre-release) application available for
download at:
bird-dog.tv/firmware
Once launched this application will list all NDI capable devices on
your network including BirdDog units and allow you to directly
open the configuration console.
Simply click 'Manage' on your BirdDog device listed in the
BirdDogFinder application, this will take you to your default web
browser and load the configuration console.
BirdDogFinder
Device Name
BIRDDOG-00122 (SDI) 192.168.0.195 Open in Web Browser
IP Address
Setting your video input
It is important to set the video input correctly within the web
configuration console, if the input is not set to the required settings
then either no video will be displayed or unexpected video results
can occur.
To access the video settings press the video menu option at the
top of the console.
Begin by selecting either AUTO or MANUAL as your primary
source setting. In most cases it is as simple as leaving the
Configuration set to Auto.
If you are not seeing the expected video results on your NDI
receiver with AUTO then manually configure the settings.
Other manuals for MINI
1
Table of contents
Other birddog Media Converter manuals
