Bin Master NCR-80 Specification sheet
925-0371
1218
NCR-80
NON-CONTACT RADAR
QUICK SETUP
BinMaster: Division of Garner Industries
7201 N. 98th St., Lincoln,NE 68507
402-434-9102 • info@binmaster.com
www.binmaster.com
925-0371
1218
2
TABLE OF CONTENTS
Quick setup using the bindisc display/adjustment module ________________ 3
Additional adjustments - Fals e s ignal suppression ____________________ 5
925-0371
1218
3
QUICK SETUP USING THE BINDISC
DISPLAY/ADJUSTMENT MODULE
1. Unscrew the housing cover.
2. Place the BinDisc display and adjustment module on the top
of the unit and turn to the right until it snaps in place.
Disassembly is carried out in reverse order
1. Press [OK], scroll to Quick setup, press [OK].
2. Measurement loop name SENSOR press [>] key.
3. Medium, press [OK], scroll to Ballast/Pebbles
Using [ >] key (do not change to anyother
me dium)
Press [OK] then press [>] key.
4. Application and Vessel bottom, press [OK]
Scroll to Bunker with [>] key, press OK
(must be in Bunker application do not change)
Vessel bottom, scroll to Conical using [>] key
Press [OK], then press [>] key.
925-0371
1218
4
4. Vessel height/Meas. Range, press [OK]
Use [>] and [+] keys to set overall height of vessel
Press [OK] then [>] key.
5. Max adjustment, press [OK]
Use [>] and [+] keys to set the headspace of the
vessel (min 2ft.)
Press [OK] then [>] key.
6. Min adjustment, press [OK]
Use [>] and [+] keys to set the overall tank height
(same as vessel height)
Press [OK] then [>] key.
7. Should now see “Successfully completed”
Note:
Please, do not deviate from these parameters unless instructed by factory
925-0371
1218
5
ADDITIONAL ADJUSTMENTS - FALSE
SIGNAL SUPPRESSION
The following circumstances cause interfering reflections and can influence the measurement:
- High standpipes
- Vessel installations such as structures, cages or ladders
- Agitators
- Buildup or welded joints on vessel walls
This should be done with a low level, so all potential interfering reflections can be detected.
1. Press [OK], scroll to Extended adjustment
Press [OK]
2. Scroll to Additional adjustments with the [>] key
Press [OK]
3. Additional adjustments, scroll to False signal
suppression
Press [OK]
Note:
A false signal suppression detects, marks, and saves these false signals
so they are no longer considered in the level measurement.
925-0371
1218
6
4. Screen shows “Change now?”
Press [OK]
5. False signal suppression, scroll to Create new
Press [OK]
6. False signal suppression, use [>] and [+] keys to set
the actual distance from the sensor to the product
surface
Press [OK]
7. Screen should now show “Executing” with a
processing bar underneath. When finished,
“Change now” will show on the screen.
Pres [ESC] key. False suppression for the actual
distance to the product will be saved.
Note:
It is critical to know the distance to the product level before doing a false signal suppression.
If the false signal suppression distance range is set to the overall height of the vessel, the product level
will be stored as a false signal and not detectable in this area.
Other manuals for NCR-80
4
Table of contents
Other Bin Master Radar manuals
Popular Radar manuals by other brands
SAW D2L
SAW D2L Valentine One Gen2 owner's manual
Raymarine
Raymarine Raytheon R20X instruction manual
Simrad
Simrad CA34 manual
Endress+Hauser
Endress+Hauser Micropilot FMR67B Brief operating instructions
Endress+Hauser
Endress+Hauser Levelflex M FMP45 operating instructions
ECHOMAX
ECHOMAX Active-X-Band manual
