Billion BIPAC 7402W User manual
BIPAC-7402 / 7402W
(Wireless) ADSL VPN Firewall Router
with 3DES Accelerator
Quick Start Guide
Billion BIPAC-7402 / 7402W (Wireless) ADSL VPN Firewall Router with 3DES Accelerator
1
Package Contents
BIPAC-7402 / 7402W ADSL Router
CD-ROM containing the online manual
RJ-11 ADSL/telephone Cable
Ethernet (CAT-5 LAN) Cable
Console (PS2-RS232) Cable
AC-DC power adapter (12VDC, 1A)
This Quick Start Guide
Do not use the BIPAC-7402 / 7402W in high humidity or high
temperatures.
Do not use the same power source for the BIPAC-7402 / 7402W
as other equipment.
Do not open or repair the case yourself. If the BIPAC-7402 /
7402W is too hot, turn off the power immediately and have it
repaired at a qualified service center.
Warning
Place the BIPAC-7402 / 7402W on a stable surface.
Only use the power adapter that comes with the package. Using
a different voltage rating power adaptor may damage the router.
Attention
For more detailed instructions on configuring and using
the (Wireless) ADSL Firewall Router, please refer to the
on-line manual.
Quick Start Guide
2
The Front LEDs
LED Meaning
1 PPP / MAIL
Lit steady when there is a PPPoA / PPPoE connection.
Lit and flashed periodically when there is email in the Inbox.
2 ADSL Lit when successfully connected to an ADSL DSLAM (“linesync”).
3 LAN Port
1X — 4X
(RJ-45 connector)
Lit when connected to an Ethernet device.
Green for 100Mbps; Orange for 10Mbps.
Blinking when data is Transmitted / Received.
4 WLAN
(7402W only) Lit green when the wireless connection is established.
Flashes when sending/receiving data.
5 SYS Lit when the system is ready.
6 PWR Lit when power is ON.
3
5
6
4
2
1
Billion BIPAC-7402 / 7402W (Wireless) ADSL VPN Firewall Router with 3DES Accelerator
3
The Rear Ports
Port Meaning
1 Power Switch Power ON/OFF switch
2 PWR Connect the supplied power adapter to this jack.
3 RESET
After the device is powered on, press it to reset the device or
restore to factory default settings.
0-3 seconds: reset the device
6 seconds above: restore to factory default settings (this is used
when you can not login to the router, e.g. forgot the password)
4 LAN
1X — 4X
(RJ-45 connector)
Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the
four LAN ports when connecting to a PC or an office/home
network of 10Mbps or 100Mbps.
5 CONSOLE Connect a PS2/RS-232 cable to this port when connecting to a
PC’s RS-232 port (9-pin serial port).
6 LINE Connect the supplied RJ-11 (“telephone”) cable to this port when
connecting to the ADSL/telephone network.
1
23
4
5
6
＊
＊Only the BIPAC-7402W has a wireless interface and antenna. BIPAC-7402
router does NOT have an antenna or wireless interface.
Quick Start Guide
4
Connecting Your ADSL Router
1. Connect the Router to a LAN (Local Area Network) and the ADSL/telephone (LINE) network.
2. Power on the device.
3. Make sure the PWR and SYS LEDs are lit steadily and that the relevant LAN LED is lit.
(For 7402W only: the WLAN LED will be lit steadily).
Billion BIPAC-7402 / 7402W (Wireless) ADSL VPN Firewall Router with 3DES Accelerator
5
Configuring PC in Windows XP
1. Go to Start / Control Panel (in Classic
View). In the Control Panel, double-click on
Network Connections
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window, click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.
Quick Start Guide
6
Configuring PC in Windows 2000
1. Go to Start / Settings / Control Panel. In the
Control Panel, double-click on Network and
Dial-up Connections.
2. Double-click Local Area Connection.
3. In the Local Area Connection Status window
click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.
Billion BIPAC-7402 / 7402W – (Wireless) ADSL VPN Firewall Router with 3DES Accelerator
7
Configuring PC in Windows 98/Me
1. Go to Start / Settings / Control Panel. In the
Control Panel, double-click on Network and
choose the Configuration tab.
2. Select TCP/IP ->
NE2000 Compatible, or the name of your
Network Interface Card (NIC) in your PC.
3. Select the Obtain an IP address
automatically radio button.
4. Then select the DNS Configuration tab.
5. Select the Disable DNS radio button and click
OK to finish the configuration.
Quick Start Guide
8
Configuring PC in Windows NT4.0
1. Go to Start / Settings / Control Panel. In the
Control Panel, double-click on Network and
choose the Protocols tab.
2. Select TCP/IP Protocol and click Properties.
3. Select the Obtain an IP address from a
DHCP server radio button and click OK.
This manual suits for next models
3
Table of contents
Other Billion Network Router manuals
Billion
Billion Modem/Router ADSL BIPAC-7100 Guide
Billion
Billion myGuard 7500GL User manual
Billion
Billion BiPAC 7402X Series User manual
Billion
Billion BiPAC 7800GZ(L) User manual
Billion
Billion BiPAC 7300NX User manual
Billion
Billion 800VGT User manual
Billion
Billion BiPAC 7402NX User manual
Billion
Billion BiPAC 7404VNOX User manual
Billion
Billion BiPAC 7404VGOX User manual
Billion
Billion BiPAC 8500 User manual
Billion
Billion BiPAC 8500 User manual
Billion
Billion BIPAC-741 GE V2.0 User manual
Billion
Billion BiPAC 7402G R3 User manual
Billion
Billion BiPAC 7800 User manual
Billion
Billion BiPAC 6404VGP R3 User manual
Billion
Billion BIPAC 5102G User manual
Billion
Billion MWEB W40 User manual
Billion
Billion BiPAC 8200N User manual
Billion
Billion BiPAC 7820NZ User manual
Billion
Billion BiPAC 7100SV User manual
