Bigassfans es6 User manual
BIGASSFANS.COM
es6
EXCEPTIONALLY
ENGINEERED
READ AND SAVE THESE INSTRUCTIONS
À LIRE ET À CONSERVER EN LIEU SÛR
LEA Y CONSERVE ESTAS INSTRUCCIONES
REV. B | 10/09/2020
☑ Prepare Fan Site
Outlet Box: Make sure your outlet box is suitable for fan support. If there is not an
outlet box at the fan location, install one on a ceiling joist or beam.
Concrete Ceiling: Install an anchor hook for the safety cable if required by your
local building and safety code. See the following page for installation details.
Wood Ceiling Joist: Attach the mounting bracket directly to the joist using two
wood screws (not supplied). Recommended: Corrosion-resistant 12-11 x 45 mm hex
head timber screws with seal. If required by local code, mount or embed an outlet
box into the joist. The outlet box must be suitable for fan support.
The mounting/fixing means for attachment to the ceiling such as hooks or other
devices shall be fixed with a sucient strength to withstand four times the
weight of the ceiling fan.
Models and Maximum Weight:
MK-ES61-052306: 25 lb (11.3 kg), MK-ES61-062306: 27 lb (12.1 kg)
Do not use the fan with a dimmer switch.
WARNING: Installation must be in accordance with the requirements set forth
by the National Electrical Code (NEC, United States), ANSI/NFPA 70, and all
national and local codes.
The ground wire must be connected to the supply ground and its length must
be longer than the safety cable.
A means for disconnection must be incorporated in the fixed wiring in
accordance with the wiring rules.
BEFORE YOU START
☑ Turn o Power at Breaker
Input Voltage: 100–277 VAC, 1 Φ, 50/60 Hz
Do not connect the fan to a damaged power
source. Do not attempt to resolve electrical failures
on your own. Contact a licensed electrician if you
are uncomfortable performing electrical work. A
licensed electrician must install the fan if required
by local code.
☑ Gather Tools
Provided with fan
© 2020 DELTA T LLC Ι ALL RIGHTS RESERVED.
☑ Prepare Concrete Ceiling (if applicable)
Drill three Ø 6 mm holes in the pattern shown. The hole depth should not exceed
40mm. Remove any dust from the holes. Insert three anchor bolts (not supplied)
into the holes. Strike the heads of the anchor bolts with a hammer, ensuring the
bolt sleeves are flush with the ceiling surface. Position the mounting bracket on the
anchor bolts. Ensure all three anchor bolts are fully tightened to expand and lock
the anchors.
If required by local building and safety codes, install an anchor hook (not supplied) for
the safety cable. Drill an Ø 8 mm hole for the anchor hook. The hole depth should not
exceed 50 mm. Remove any dust from the hole, and then insert the anchor hook and
fully tighten.
Ø 6 mm
45 mm 43 mm
112 mm
50 mm max
40 mm max
REV. B | 10/09/2020
PARTS AND HARDWARE
EMI filter not shown.
Mounting Bracket
Lower Cover or Light Kit
Mounting Ball
and Wedge
Canopy Screws (4)
Canopy
6 mm Steel Pin
Downrod
Wiring Cover
M6 x 32 mm Bolt M6 Nut
Airfoils (6)
Wire Connectors
Motor Unit
Wiring and Safety Cable
© 2020 DELTA T LLC Ι ALL RIGHTS RESERVED. 1
INSTALLATION
1. Install downrod and wiring harness
Align holes on downrod with holes on motor bracket. Secure downrod with the M6 x
32mm bolt and M6 nut (Fig. 1.1).
Fig. 1.1
M6 x 32 mm Bolt
M6 Nut
Connect wiring harness from downrod to receptacle from motor unit (Fig. 1.2).
Fig. 1.2
Wiring Harness
REV. B | 10/09/20202
2. Install lower safety cable and ground wire
Install safety cable and ground wire lugs with unpainted screws and lock washers
(Fig.2.1).
Fig. 2.1
Ground Wire
(Green)
Safety Cable
Lock
Washer
Screw
Make sure all hardware is secure, and then gently tug cables at top of downrod to
reduce slack (Fig. 2.2).
Fig. 2.2
© 2020 DELTA T LLC Ι ALL RIGHTS RESERVED. 3
3. Position wiring cover and canopy
Slide wiring cover down downrod, resting it on the fan hub. Make sure no wires are
visible between the cover and fan hub. Slide canopy down downrod, resting it on the
wiring cover (Fig. 3).
Fig. 3
Canopy
Wiring Cover
4. Install mounting ball
Slide mounting ball over downrod (Fig. 4.1).
Insert 6 mm steel pin into hole at top of downrod, and then slide the mounting ball
upward, seating the steel pin in the inner slots (Fig. 4.2).
Insert wedge into mounting ball and secure with screw. Tighten screw enough to
prevent movement between the mounting ball and downrod, but do not over-tighten
(Fig. 4.3).
Fig. 4.1
MountingMounting
BallBall
Downrod
6 mm Steel Pin
Screw
Wedge
Fig. 4.2 Fig. 4.3
REV. B | 10/09/20204
5. Install mounting bracket
Disconnect power to fan location before installing mounting bracket.
WARNING: Mount only to an outlet box marked acceptable for fan support.
Secure mounting bracket to mounting structure with suitable hardware (not supplied)
(Fig. 5). Outlet box shown. Your mounting structure may dier from the illustration.
Power supply omitted from mounting bracket illustration for clarity.
Fig. 5
Suitable Mounting Hardware
6. Hang fan
Raise fan to mounting bracket. Align rib in mounting bracket with slot in mounting ball,
position mounting ball, and let fan hang freely (Fig. 6).
Gently twist downrod to ensure it is properly seated and will not move during fan
operation.
Fig. 6
Mounting Ball
Mounting Bracket
Mounting Bracket
© 2020 DELTA T LLC Ι ALL RIGHTS RESERVED. 5
7. Wire fan
Disconnect power to fan location before wiring fan.
Wire fan as shown using the wire connectors (Fig. 7). Attach green ground wire to
mounting bracket with the unpainted screw. Connect wiring harness from power supply
to wiring harness from downrod, making sure that the wiring and safety cable are routed
in the same direction.
Carefully tuck wiring into outlet box or building structure. Ensure wire connectors are
turned upward and that wires are spread apart with grounded conductors on one side
of the outlet box/mounting structure and ungrounded conductors on the other side.
Fig. 7
North America 100–120 V Australia All other regions
AC Hot/L1
Brown Black Brown or Red Brown
AC Neutral/L2
Blue White Black or Light Blue Blue
PE/Earth Ground
Green with Yellow Green or Bare Copper Green with Yellow Green with Yellow
Supply Power Wire Color Chart
AC HOT/L1
BROWN
AC NEUTRAL/
L2
PE/EARTH
GROUND
BLUE
GREEN &
YELLOW
EMI Filter
Power Supply
Wiring Harnesses
Mounting Bracket
Safety
Cable
RED Wire Connector
REV. B | 10/09/20206
8. Install fan stabilizer (optional, outdoor fans only)
The fan stabilizer is included only if purchased as an outdoor fan accessory.
If you purchased the fan stabilizer kit, fit stabilizer into notches on top of mounting ball
(Fig. 8.1).
Fig. 8.1
Mounting Ball
Fan Stabilizer
Secure stabilizer plate to stabilizer with the M6 x 70 mm bolt and M6 nut (Fig. 8.2).
Fig. 8.2
M6 Nut
Stabilizer Plate M6 x 70 mm Bolt
Table of contents
Languages:
Other Bigassfans Fan manuals
Bigassfans
Bigassfans AirEye User manual
Bigassfans
Bigassfans COOL-SPACE 300 User manual
Bigassfans
Bigassfans 8'-24' Powerfoil X User manual
Bigassfans
Bigassfans Powerfoil X3.0 Plus User manual
Bigassfans
Bigassfans 2025 User manual
Bigassfans
Bigassfans Yellow Jacket User manual
Bigassfans
Bigassfans Powerfoil Breeze User manual
Bigassfans
Bigassfans Basic 6 User manual
Bigassfans
Bigassfans COLD FRONT 300 User manual
Bigassfans
Bigassfans 2025 User manual
Bigassfans
Bigassfans HAIKU MK-HK4-042406 User manual
Bigassfans
Bigassfans Yellow Jacket User manual
Bigassfans
Bigassfans AirEye Series User manual
Bigassfans
Bigassfans 4900 User manual
Bigassfans
Bigassfans Powerfoil 8 Plus User manual
Bigassfans
Bigassfans Sweat Bee Operating and maintenance instructions
Bigassfans
Bigassfans Pivot 180 User manual
Bigassfans
Bigassfans Yellow Jacket User manual
Bigassfans
Bigassfans Haiku 52 User manual
Bigassfans
Bigassfans Essence User manual
Popular Fan manuals by other brands
ELTA FANS
ELTA FANS H03VV-F installation guide
Hunter
Hunter 20714 Owner's guide and installation manual
Emerson
Emerson CARRERA VERANDA CF542ORB00 owner's manual
Hunter
Hunter Caraway Owner's guide and installation manual
Panasonic
Panasonic FV-15NLFS1 Service manual
Kompernass
Kompernass KH 1150 operating instructions
