BFT Lux BT QSG User manual

Lux BT QSG

(see also Thalia P or Libra CLX QRG)

Quick reference guides are not a replacement for the supplied instructions, they are supplementary

Read and understand the installer warnings in the main instruction document first

Always apply good, safe, state of the art engineering and electrical installation principles

Safety of the completed installation is the ultimate responsibility of the installer

This product is not suitable for DIY use and should only be installed and maintained by a trained, skilled, professional installer

Geometry

This motor will work best when A = B, any other configuration will detract

from its performance and could affect reliability

A

B

C

Lux BT – A = 135mm B = 135mm C = 1050mm

Lux G BT – A = 195mm B = 195mm C = 1295mm

Geometry

Extreme difference between A and B should be avoided at all

cost, and will only work on the lightest gates in perfect locations

and with perfect set up

End of Stroke Limit

The rams need a

degree of travel left un

used in the open and

closed positions

If these dimensions are

exceeded the encoder

will not accept the limit

positions and give ER

SU during the set up

procedure

Length, Weight and Locks

Leaf weight/length should not exceed;

Lux BT 300Kg/2m

Lux G BT 800Kg/3m

300kg/5m

Where the G BT is used on gates over 3m length, it must be used in

non locking form. Turn both valves fully anti clockwise after set up

Ground stops are recommended in the open and closed positions.

Neither motor is recommended for use with wind affected gates.

Open and Close locks are

provide on either side of the

release valve

10 11 14 15 41 42 43

Wiring

Libra CLX Thalia P

Use 3 core externally rated flex in accordance with

BS7671

1.5mm2 up to 10m

2.5mm2 up to 20m

Method Libra CLX

Fit the motors and check the end of stroke limits

Close the gates and lock off

Wire in the motors

Run “LSU ADJ” (the aim is to stop at the stop, not hit the stop)

•Press and hold top button – lift off at open point – “OK” (M2 Open)

•Press and hold top button – Lift off at open point “OK” (M1 Open)

•Press and hold middle button – Lift off at close point “OK” (M1 Close)

•Press and hold middle button – Lift off at close point “OK” (M2 Close)

Run “AUTOSET”

Increase N1T and N2T to 25%

Increase SLOW SPEED to 35%

Fit accessories one at a time and test each before moving on

Method Thalia P

Fit the motors and check the end of stroke limits

Close the gates and lock off

Wire in the motors

Run the quick menu – Press OK once

Follow the prompts to “LSU ADJ”

•Press and hold top button – lift off at open point – “OK” (M1 Open)

•Press and hold top button – Lift off at open point “OK” (M2 Open)

•Press and hold middle button – Lift off at close point “OK” (M2 Close)

•Press and hold middle button – Lift off at close point “OK” (M1 Close)

Run “AUTOSET”

Increase OPEN FORCE and CLOSE FORCE to 25%

Increase SLOW SPEED to 35%

Fit accessories one at a time and test each before moving on

Adjust close delay to give 700mm min. between M2 and M1 at closing

Adjust slow speed to cut in at 700mm from closed

Measure force/time at 500mm distance in line with the motor

Thalia P;

Increase close force & slow speed to just below 150N

Libra CLX;

Adjust N2T and SLOW speed to just below 150N

Run a full set of tests

Address all other risks as appropriate

MD Compliance

This manual suits for next models

2

Popular Door Opening System manuals by other brands

Pamex

Pamex KT-INP35 Installation instruction

Label

Label NEPTIS/LE installation manual

Cal-Royal

Cal-Royal N-F77CVR Installation instruction

Scrigno

Scrigno OPEN1000 Assembly manual

TriMark

TriMark UM 34 instructions

Alecto

Alecto ADI-250 user manual

Besam

Besam Swingmaster MP Installation, adjustment and maintenance instructions

CRL

CRL SENIOR PRIMA manual

Assa Abloy

Assa Abloy SARGENT 1431 Series instructions

GAL

GAL MOVFR Quick setup

Olide

Olide 120B installation manual

Normstahl

Normstahl IDO7 installation manual

Häfele

Häfele Finetta T 70 VF manual

AGS

AGS D-PL Instructions for fitting, operating and maintenance

Stanley

Stanley MA900ñ Installation and owner's manual

WITTUR

WITTUR Hydra Plus UD300 Instruction handbook

Alutech

Alutech TR-3019-230E-ICU Assembly and operation manual

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and OPERATING AND INSTALLATION Manual