Unite AP4
Access Point
beyerdynamic GmbH & Co. KG
Theresienr. 8 •74072 Heilbronn – Germany
Tel. +49 (0) 71 31 / 617 - 300 • info@beyerdynamic.de • www.beyerdynamic.com
For fuher diributors worldwide, please go to www.beyerdynamic.com
Non-contractual illurations. Contents sub ect to change without notice. E3 / Unite AP4 (12.19)
1 of 11
VERSIONS
Unite AP4 (EU) Digital 4-channel access point
with integrated antennas,
network connection, USB-C,
Dante® interface (PoE),
4 analogue inputs and outputs
integrated wall and stand mounting,
incl. power supply,
variant for Europe,
1880 - 1900 MHz . . . . . . . . . . Order # 710.482
Unite AP4 (NA) same as above, but variant
for North America,
1920 - 1930 MHz . . . . . . . . . . Order # 739.456
Unite AP4 (JP) same as above, but variant
for Japan,
1894 - 1906 MHz . . . . . . . . . . Order # 739.464
These three versions may only be used in the appropriate
regions and are not compatible with each other.
Trademark
The Dante® word mark and logos are regiered trademarks of Audinate
Pty. Ltd and all use of these trademarks by beyerdynamic is licensed. Other
trademarks and trade names are the propey of the respective owners.
APPLICATIONS
The Unite AP4 access point is a multifunctional device
with which various applications can be realised.
With one Unite access point 4 audio channels can be
wirelessly transmitted. For a maximum of 32 channels
8 Unite AP 4 can be synchronised in one network.
Depending on the configuration, the device works as a
transmitter (Broadcast mode) or a receiver with back (Full
Duplex mode).
As a transmitter, the Unite AP4 transmits the audio signals
of an external audio source on a maximum of 4 DECT
channels. Typical applications are e.g. interpreting
services in con unction with an interpreting system,
assistive listening and wireless microphone applications.
When using several Unite AP4 devices in different
operating modes, almost any applications can be
combined. Via the Ethernet connection, a maximum of
8 Unite AP4 devices can be integrated into a network
consisting of many Unite components. One or more
Unite AP4 devices can be configured using the free Unite
Manager PC Software. This also enables additional
functionalities in the Unite network such as monitoring,
maintenance, comprehensive configuration, pairing and
setup of transmitters, receivers, chargers and Unite AP4
access points.
H w t use the Unite AP4 in a DANTE® netw rk
The DANTE® Audio Interface (DAI) built into the Unite AP4
supports two flows in the DANTE® network at a fixed
sample rate of 48 kHz.
Each flow contains 1 to 4 channels. The configuration is
done in the free DANTE® controller of the company
Audinate®
The following combinations are possible:
• One connected device with 4 channels
• One connected device with 1 channel +
one connected device with 3 channels
• Two connected devices with two channels each
FEATURES
• 4-channel access point
• High range
• Integrated antennas
• Digital Dante® interface (4 In / 4 Out)
• Ethernet interface (network)
• 4 analogue inputs and outputs (Phoenix®)
• Power supply via PoE (Power over Ethernet)
• With 8 synchronised access points a maximum
of 32 audio channels can be transmitted
• Removable mounting plate for wall or ceiling
mounting, on a tripod or via VESA adapter plate
SUPPLIED ACCESSORIES
• External 36W power supply with power cable and
mains plug (EU: CEE7/16, NA & JP: NEMA 1-15, 2-pin) and
C7 device plug
• Thread adapter 1/2" – 3/8" for tripod mounting
• 2 x Phoenix® connectors (FMCD 1,5/6-ST-3,5),
contact spacing 3.5 mm, two rows, 6-pin
• 4 x cover plates for cable feed-through of the wall
mount (pre-assembled)
• 4 x M5x10 screws (for Vesa adapter plate)
• 4 x M5 nut (for Vesa adapter plate)
• Installation instructions
