Beta 350-498 RR User guide

2013 –2014 350-498 RR

Set Up Manual

8/2013

1) Remove cardboard from

crate. Remove bag with bolts

and upper handle bar clamp

taped to the protective

covering over the seat.

Remove all items from bottom

of crate

2) ) Remove wood support from

lower bar mount and discard.

Retain bolts for handle bar. Remove

protective covering from

motorcycle and handle bar.

3) Install handle bars using the

supplied 8mm bolts and upper

clamp bracket. Torque bolts to 25

nm.

4) Remove additional items from

the box supplied. Item list is as

follows:

-Headlight assembly

-Skid plate

-Frame guards

-Tool kit

-Battery Strap

-Owners manual

-Hardware

6) Cut large tie straps form foot rests

5) Carefully remove Tie-Straps from

front and rear wheels making sure the

motorcycle doesn’t fall over. Remove

the motorcycle from the crate.

7) Attach the computer using the

bolts located on the top triple

clamp. Torque to 10nm.

8) Insert all the electrical

connectors into the matching plugs

located below the computer

including those hanging from the

handle bar.

9) Attach the headlight

connectors located behind the

headlight mask to the proper

plugs located below the

computer.

10) Install the headlight mask bottom

by inserting the lower tab into slot

located in the front fender brace.

11) Finish by securing the rubber

straps located on the sides of the

mask to the upper fork legs.

12) Press the front brake line and

speedometer wire through the slot

on the grommet located on the left

side of headlight mask.

13) Locate the skid

plate and install the

four foam buffers as

shown.

14) Install the skid

plate clips to the tabs

on the lower front frame

rails. Use the two 6mm

bolts to secure the front

of the skid plate.

15) Using the threaded

hole at the lower rear

of the frame, secure the

rear of the skid plate using

the remaining 6mm bolt.

16) Install the right and left frame

guards with zipties and the one bolt

into the swingarm pivot. Make sure

there is one ziptie tied around the

rear brake master cylinder also.

17) Wearing a glove, use your

finger to apply a bead of grease

around the inside edge of the air

filter. This will help keep debris

from passing through. Re-install

the filter making sure all corners

are firmly in place.

18) Holding the Battery, peel the

adhesive sticker from the top.

19) Line up the cells on the

container with the holes on the

top of the battery. Push down

to puncture the foil covers .

This will allow the electrolyte

to drain into the Battery.

20) Firmly push solution cover

on so it sits flush with top of

Battery. Let Battery sit for 1

hour before charging.

21) Charge the Battery at 1 or 2

Amps for 6 to 8 hours.

Install battery and fill the

motorcycle with oil.

22) Congratulations! You have just set up

a new Beta!

Follow the checklist on the customer’s

warranty registration card for a complete

pre-delivery inspection before delivery.

Popular Motorcycle manuals by other brands

OHVALE

OHVALE GP-0 Use & maintenance

Yamaha

Yamaha Star XV19CTSZ 2009 owner's manual

KTM

KTM 350 XCF-W USA owner's manual

HYOSUNG

HYOSUNG ST7 owner's manual

Husqvarna

Husqvarna FC 250 2016 owner's manual

Ducati

Ducati SCRAMBLER 800 Workshop manual

MOTO GUZZI

MOTO GUZZI QUOTA 1100 ES owner's manual

APRILIA

APRILIA ETV MILLE CAPONORD - PART1 02-2001 manual

Yamaha

Yamaha 2006 YZF-R1V owner's manual

KTM

KTM Freeride E-XC 2021 owner's manual

Fantic

Fantic Enduro 125 user manual

Ducati

Ducati Supersport 750 desmodue owner's manual

MV Agusta

MV Agusta 2008 F4 312RR 1078 Workshop manual

Yamaha

Yamaha XVS650A owner's manual

Yamaha

Yamaha YZF-R6T(C) Supplementary service manual

Ducati

Ducati 748 monoposto strada owner's manual

ATK

ATK 1988 250 owner's manual

Excelsior-HENDERSON

Excelsior-HENDERSON 1999 HCX Riders handbook