Bentel Security Academy 4 Operating instructions

BENTEL SECURITY srl reserves the right to modify the technical specifications of this product

without prior notice.

Digital Communicator Control Panel

Emission:

Immunity:

Low voltage:

Burglar alarm systems:

EN 50081-1/1992

EN 50130-4/1995+A1/1999

EN 60950/1996 + A4/1997

CEI 79/2 2 Ed. 1993

TBR21-1/1993

complies to:

Terminal Equipment(TE):

BENTEL SECURITY declines all responsibility in the event of

unauthorized intervention on the control panel.

The control panel has been developed and made according to the highest

standards of quality, reliability and performance adopted by BENTEL

SECURITY srl.

To make sure your system continues to work as intended, you must test your

system every month. Consult the installer for testing and maintenance

instructions. If your system does not work correctly, call your installer for

service.

Installation of the control panel must carried out strictly according to the

instructions, and in compliance with the safety laws in force.

via Florida - Z.I. Valtesino - 63013 GROTTAMMARE (AP) - ITALY

INSTALLATION MANUAL: Digital communicator control panel

ISTRUZIONI PR.TAST.UK BENT.ACADEMY4/8/8L ISTPTBLEACADEMY8

CONTENTS

PROGRAMMING FROM KEYPAD 5

Restrictions . . . . . . . . . . . . . . . . . . . . . . . . 5

Access to programming . . . . . . . . . . . . . . . . . 5

Programming structure and modes . . . . . . . . . . . 6

Programming Modes . . . . . . . . . . . . . . . . . . . 7

Address tables . . . . . . . . . . . . . . . . . . . . . . 11

Keypads parameters (Addresses 1 through 9) . . . . . 11

Key readers 1 through 8 parameters (Addresses 10 through 34)12

Key readers 9 through 16 parameters (Addresses 35 through 59)13

Zone programming . . . . . . . . . . . . . . . . . . . 14

Outputs parameters (Addresses 100 through 111) . . . 16

Times . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Telephone Numbers (Addresses 126 through 157) . . 17

Customer Telephone Options (Address 158) . . . . . 19

Teleservice (Addresses 159 through 164) . . . . . . . 19

Codes (Addresses 165 through 256) . . . . . . . . . . 20

Installer PIN (Address 257) . . . . . . . . . . . . . . . 23

Scheduler (Addresses 258 through 289) . . . . . . . . 23

Clock (Address 290) . . . . . . . . . . . . . . . . . . 24

Events (Addresses 291 through 418) . . . . . . . . . . 25

Programming digital keys (Addresses 419 through 422) 29

Options (Addresses 423 to 425) . . . . . . . . . . . . 30

Events (Address 426) . . . . . . . . . . . . . . . . . . 32

Telephone (Address 427) . . . . . . . . . . . . . . . 32

Options (Address 428) . . . . . . . . . . . . . . . . . 32

Options (Address 429) . . . . . . . . . . . . . . . . . 32

Options (Address 430) . . . . . . . . . . . . . . . . 32

4Security System Control panel

PROGRAMMING FROM KEYPAD

For in-detail information on the following parameters and options refer to the

"PROGRAMMING" chapter.

All the control panel parameters can be programmed from the keypad.

Only the INSTALLER PIN and MAIN USER PINs can access the program-

ming phase.

+The control panel will be out of service (alarm outputs disabled) during

the programming phase.

Restrictions

The Installer can program all the control panel parameters, with the excep-

tion of Code PINs 1 through 23.

A Main User Code PIN can change all User, Duress and Patrol Code

PINs enabled on the group of partitions it controls (see below).

CODE No. TYPE ASSIGNED

PARTITIONS

Code1 MAIN USER 1- 3- 4

Code2 MAIN USER 2- 3

Code3 USER 1- 3

Code4 USER 4

Code5 USER 3 - 4

Code6 PATROL 2

Code7 DURESS 3

Code8 USER 2 - 3

In the example above MAIN USER Code 1can change its own PIN and

the PINs of: Code 3, Code 4, Code 5 and Code 7.

MAIN USER Code 2 can change its own PIN and the PINs of: Code 6,

Code 7 and Code 8.

NC2TAST or ICON/KP keypads can be connected to the Panel. The key

functions on the NC2TAST and ICON/KP keypads are identical, however, the

key icons differ. The following description refers to the NC2TAST keypad.

Access to programming

The control panel must be disarmed.

INSTALLER

Enter the INSTALLER PIN then press .

PROGRAMMING FROM KEYPAD 5

MAIN USER

Enter a MAIN USER PIN, press then press .

+Access to programming will be signalled by slow flashing on LED 7 and a long

high-tone beep.

Programming structure and modes

Structure Programming comprises two distinct phases----shown by the ON /OFF

status of LED L6.

PHASE 1----ENTER PARAMETER ADDRESS----LED L6 OFF

ØPhase 1----enter the Address of the parameter to be programmed (maxi-

mum 3 digits) then press .

Access to PHASE 2 will be signalled by a long high-tone beep.

Access Denied will be signalled by a long low-tone beep. Retry after error

beep.

+Press to exit the programming phase.

PHASE 2----ENTER PARAMETER VALUE----LED L6 ON

ØPhase 2----enter the parameter value then press .

The Panel status: partitions, options, attributes, etc., can be viewed by

means of the LEDs under the number keys. An audible acceptance or er-

ror signal will be emitted when the keys are pressed.

Telephone numbers, PINs and times cannot be viewed on the keypad, and

the LEDs under the number keys will be OFF.

Figure 1 LEDs and keys

6Security System Control panel

Press to step back to PHASE 1.

+Press to save the parameter values.

Programming Modes

There are three parameter programming modes: Single mode, Consecu-

tive mode, Multi-section mode. Refer to examples 1, 2 and 3.

Refer to the parameter Address tables for: a brief description; the accepted

keys and / or values of each parameter and the programming mode (see

example 4).

Single mode The usymbol means the parameter can be programmed in Single mode only.

Step 1 Enter the parameter Address then press .

Step 2 Enter the parameter value then press .

(See example 4)

Consecutive

Mode The îsymbol means the parameter can be programmed in Single mode

and Consecutive mode.

Consecutive mode (for zones, outputs and telephone numbers) requires

the Address of the first parameter only,as follows.

Step 1 Enter the Address then press .

Step 2 Enter the parameter value then press .

Step 3 Enter the value of the next parameter then press , and so forth.

(See example 2)

Multi-section

Mode The vsymbol means the parameter must be programmed in Multi-sec-

tion mode.

Multi-section mode parameters have more than one section (e.g. Clock

parameter). Therefore, it will be necessary to press after completing

each section.

Step 1 Enter the Address then press .

Step 2 Enter the value of the first section then press .

Step 3 Enter the value of the second section then press .

(See example 3)

PROGRAMMING FROM KEYPAD 7

Example 1

Step 1 Enter the Installer PIN

Step 2 Press .

PHASE 1 active----LED L7 will flash slowly.

Step 3 Enter a valid Address (e.g. Address 1 for Keypads in configuration----ac-

cepted keys through ) then press .

PHASE 2 active----LED L6 ON.

Step4 Setup the keypads in configuration----accepted keys through .

Step 5 Press to save and step back to PHASE 1.

Step 6 Repeat the procedure from Step 3 for the other parameters.

If is pressed when PHASE 1is active the programming session will

close.

If is pressed when PHASE 2 is active the current parameter will not

be saved and the control panel will step back to PHASE 1 Step 3.

+Press to save the parameter value.

Example 2

Step 1 Enter the Installer PIN.

Step 2 Press .

PHASE 1 active----LED L7 will flash slowly.

Step 3 Enter a valid Address (e.g. Address 60 for Partition assignment Zone----

accepted keys through ) then press .

PHASE 2 active----LED L6 ON.

Step 4 Assign the partitions for zone 1----accepted keys through .

Step 5 Press to save parameter 60 and step to parameter 61 (Type Zone

1).

PHASE 2 active----LED L5 ON.

Step 6 Program the Type for zone 1----accepted keys through .

8Security System Control panel

Step 7 Press to save parameter 61 and step to parameter 62 for Balance

type Zone 1.

PHASE 2 active----LED L4 ON.

Step 8 Program the Balance Type for zone 1----accepted keys through .

Step 9 Press to save parameter 62 and go to parameter 63 for Attributes

Zone 1.

PHASE 2 active----LED L3 ON.

Step 10 Program the Attributes for zone 1 ----accepted keys through .

Step 11 Press to save parameter 63 and go to parameter 64 for Alarm cy-

cles Zone 1.

PHASE 2 active----LED L2 ON.

Step 12 Enter the number of Alarm cycles for zone 1----values 0through 15.

Step 13 Press to save parameter 64 and step back to PHASE 1 Step 3

LED 7 will flash----all other LEDs will be OFF.

If is pressed when PHASE 1is active programming session will

close.

If is pressed when PHASE 2 is active the current parameter will not

be saved and the control panel will step back to PHASE 1 Step 3.

+Press to save the parameter value.

Example 3

Step 1 Enter the Installer PIN.

Step 2 Press .

PHASE 1 active----LED L7 will flash slowly.

Step 3 Enter a valid Address (e.g. event 325 SUPERKEY 1----refer to "User Manual").

Step 4 Press :

PHASE 2 active----LED L6 ON

This is a Multi-section parameter with three sections:

Calls - Event Code - Voice Message. The telephone numbers (first sec-

tion) will be called when the assigned event occurs.

PROGRAMMING FROM KEYPAD 9

Step 5 Enter the identifier number of the telephone number----accepted keys

through .

Step 6 Press to save the data in the Calls section and step to the Event

Code section.

PHASE 2 active----a LED will go ON to confirm parameter acceptance.

Step 7 Enter the 2 digit event code for the SUPERKEY 1 event----accepted keys

through .

Step 8 Press to save the data in the Event Code section and step to the

Voice Message section.

PHASE 2 active----a LED will go ON to confirm parameter acceptance.

Step 9 Select the voice message for the SUPERKEY 1 event (refer to User Manual)----

accepted keys through .

+Press for no message.

Step 10 Press to save the data in the Voice Message section and go back to

PHASE 1 Step 3.

LED 7 will flash----all other LEDs will be OFF.

If is pressed when PHASE 1 is active the programming session will close.

If is pressed when PHASE 2 is active the current parameter will not

be saved and the control panel will step back to PHASE 1 Step 3.

+Press to save the parameter value.

Example 4 Parameter 1 (Keypads in configuration)----accepted keys through .

A brief description of the parameter can be found at the top of the KEY-

PADS table.

The usymbol at the end of the row means the parameter can be pro-

grammed in the Single mode only.

Parameter 131 (Call Type for telephone number 2)----accepted keys

through and .

A brief description can be found at the top of the TELEPHONE table.

The îsymbol at the end of the row in the programming tables means the pa-

rameter can be programmed in both Single mode and Consecutive mode.

Parameter 290 (Clock): data entry instructions can be found at the top of

the CLOCK table.

The vsymbol between the "day - month - year" and also "hour and min-

utes" sections means the parameter must be programmed in Multi-sec-

tion mode.

10 Security System Control panel

This manual suits for next models

Table of contents

Other Bentel Security Control Panel manuals

Bentel Security

Bentel Security FireClass100 Mounting instructions

Bentel Security

Bentel Security BW-ODT User manual

Bentel Security

Bentel Security KYO 320 User manual

Bentel Security

Bentel Security ABSOLUTA ABS16P15 User manual

Bentel Security

Bentel Security FireClass 200 User manual

Bentel Security

Bentel Security NormaOtto Series User manual

Bentel Security

Bentel Security Absoluta Instruction manual

Bentel Security

Bentel Security FireClass 200 User manual

Bentel Security

Bentel Security FireClass FC500IP User manual

Bentel Security

Bentel Security Omnia User manual

Bentel Security

Bentel Security KYO 320 User manual

Bentel Security

Bentel Security KYO 4 M User manual

Bentel Security

Bentel Security Omnia 8/L User manual

Bentel Security

Bentel Security Academy8L User manual

Bentel Security

Bentel Security K-NET User manual

Bentel Security

Bentel Security KYO 320 User manual

Bentel Security

Bentel Security FireClass 100 User manual

Bentel Security

Bentel Security KYO 320 User manual

Bentel Security

Bentel Security KYO 320 User manual

Bentel Security

Bentel Security KYO 320 User manual

Bentel Security

Bentel Security KYO 100 User manual

Bentel Security

Bentel Security OmniaTAST-R User manual

Bentel Security

Bentel Security KYO-Unit Series User manual

Bentel Security

Bentel Security ABSOLUTA 16 User guide

Popular Control Panel manuals by other brands

RDZ

RDZ PC-HRX user manual

STG-BEIKIRCH

STG-BEIKIRCH MZ3 operation instruction

Efka

Efka Variocontrol V810 instruction manual

Cebora

Cebora 208-10 instruction manual

AMX

AMX AutoPatch CP-15 instruction manual

Satel

Satel CA-6 KLED-S user manual

Evolution

Evolution IQ plus 800 installation manual

Fagor

Fagor 8040 TCO CNC operating manual

Trane

Trane ComfortLink II XL950 Control user guide

AKO

AKO PROCool AKO-17635-2 quick guide

ABB

ABB 6136/30M-101 operating instructions

Telikou

Telikou BK-603 Belt Pack instruction manual

Mapei

Mapei Mapeheat Thermo Touch user guide

Bosch

Bosch D9412GV4 owner's manual

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 user manual

Sminn

Sminn BOX L VF1L EI instruction manual

Balboa

Balboa TP600 user manual

Nice

Nice HSCU1 Instructions and warnings for installation and use