Belden HIRSCHMANN MACH 100 Series User manual

MACH 100

Release

07/10

Technical Support

[email protected]

User Manual

Installation

Industrial ETHERNET Workgroup Switch

MACH 100 Family

MACH 102-8TP-F

MACH 102-24TP-F

MACH 102-8TP + M1-8TP-RJ45 + M1-8MM-SXC

MACH 102-8TP + M1-8SM-SXC + M1-8SFP

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use. For devices with embedded software, the end-user license agreement on the

enclosed CD applies.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.beldensolutions.com).

Printed in Germany

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Tel.: +49 1805 141538

039 710-001-04-07/10 – 16.7.10

MACH 100

Release

07/10 3

Contents

Safety instructions 4

About this manual 10

Legend 10

1 Device description 11

1.1 Description of the device variants 12

1.1.1 MACH 100 basic device 12

1.1.2 MACH 100 media modules 16

1.1.3 SFP modules 19

2 Assembly and start-up 21

2.1 Installing the device 21

2.1.1 Unpacking and checking 21

2.1.2 Installing the media modules 21

2.1.3 Installing the SFP modules 23

2.1.4 “FAULT” signal contact 24

2.1.5 Dimension drawings 25

2.1.6 Installing the device and grounding 25

2.1.7 Supply voltage 28

2.1.8 Startup procedure 31

2.1.9 Connecting the data lines 31

2.2 Display elements 34

2.3 Basic set-up 36

2.4 Disassembly 38

3 Technical data 40

A Further Support 47

4MACH 100

Release

07/10

Safety instructions

This documentation contains instructions which must be observed to ensure

your own personal safety and to avoid damage to devices and machinery.

Certified usage

The device may only be employed for the purposes described in the

catalog and technical description, and only in conjunction with external

devices and components recommended or

approved by the manufacturer. The product can only be operated cor-

rectly and safely if it is transported, stored, installed and assembled pro-

perly and correctly. Furthermore, it must be operated and serviced

carefully.

Supply voltage

The supply voltage is electrically isolated from the housing.

Use undamaged parts.

The device does not contain any service components. Internal fuses

are only triggered if there is a fault in the device. If the device is not

functioning correctly, or if it is damaged, switch off the voltage supply

and return the device to the plant for inspection.

Only switch on the device when the housing is closed.

Only use connection cables that are permitted for the specified

temperature range.

Relevant for North America:

Only use copper wire/conductors of class 1, 60/75°C or 75°C.

Warning!

Only connect a supply voltage that corresponds to the type plate

of your device.

Warning!

Use a fuse for the PoE supply voltage feed of the M1-8TP-

RJ45 PoE media module: 5 A slow blow.

Warning!

Disconnect the PoE voltage supply before removing the

M1-8TP-RJ45 PoE media module.

Warning!

Make sure that service personnel always have easy access to all

voltage supply connections of the basic device and the

M1-8TP-RJ45 PoE media module.

MACH 100

Release

07/10 5

Make sure that the disconnecting device is easily accessible so that

the MACH 100 device can be disconnected from the mains voltage.

If you disconnect the device from the mains voltage using

- the plug in the socket

- an on/off switch

it must be easily accessible.

Hinweis: For devices with redundant voltage supply (MACH 102-8TP-R,

MACH 102-8TP-FR, MACH 102-24TP-FR), both non-heating appliance

plugs must be pulled to disconnect the device from the main voltage. If the

M1-8TP-RJ45 PoE media module is used, the supply voltage also has to

be switched off or disconnected.

Shielding ground

The shielding ground of the connectable twisted pair lines is connected to

the protective conductor connection via the front panel.

Beware of possible short circuits when connecting a cable section with

conductive shielding braiding.

Housing

Only technicians authorized by the manufacturer are permitted to open

the housing.

The device is grounded via the voltage supply socket.

Make sure that the electrical installation meets local or nationally

applicable safety regulations.

The ventilation slots must not be covered so as to ensure free air

circulation.

The clearance to the ventilation slots of the housing must be at least

10 cm (3.94 in).

Warning!

Never insert sharp objects (small screwdrivers, wires, etc.) into

the inside of the product. There is the risk of an electric shock.

Close all empty slots with a covering panel.

The device must be installed in the horizontal or upright position, either

as a table unit in the switch cabinet (see fig. 16) or on the wall (see

fig. 17).

If you are operating the device in a 19" switch cabinet: install sliding/

mounting rails for holding the device (see fig. 15).

Environment

The device may only be operated at the specified maximum ambient

temperature (temperature of the surrounding air at a distance of up to 5

cm (1.97 in) to the device) and relative air humidity.

6MACH 100

Release

07/10

Install the device in a location where the climatic threshold values

specified in the technical data are adhered to.

Only to be used in an environment with a pollution degree specified in

the technical data.

Qualification requirements for personnel

Qualified personnel as understood in this manual and the warning signs,

are persons who are familiar with the setup, assembly, startup, and

operation of this product and are appropriately qualified for their job. This

includes, for example, those persons who have been:

trained or directed or authorized to switch on and off, to ground and to

label power circuits and devices or systems in accordance with current

safety engineering standards;

trained or directed in the care and use of appropriate safety equipment

in accordance with the current standards of safety engineering;

trained in providing first aid.

General safety instructions

Electricity is used to operate this equipment. Comply with every detail of

the safety requirements specified in the operating instructions regarding

the voltages to apply (see page 4).

Warning!

Only trained service personnel are authorized to plug the

M1-8TP-RJ45 PoE media module into the basic device or

remove from the basic device.

Non-observance of these safety instructions can therefore cause material

damage and/or serious injuries.

Only appropriately qualified personnel should work on this device or in

its vicinity. These personnel must be thoroughly familiar with all the

warnings and maintenance procedures in accordance with this

operating manual.

The proper and safe operation of this device depends on proper

handling during transport, proper storage and assembly, and

conscientious operation and maintenance procedures.

Never start operation with damaged components.

Only use the devices in accordance with this manual. In particular,

observe all warnings and safety-related information.

Any work that may be required on the electrical installation may only

be carried out by personnel trained for this purpose.

MACH 100

Release

07/10 7

Please note that products recommended as accessories may have

characteristics that do not fully correspond to those of the

corresponding product. This may limit their possible usage in the

overall system.

Note: LED or LASER components in compliance with IEC 60825-1

(2001):

CLASS 1 LASER PRODUCT

CLASS 1 LED PRODUCT

National and international safety regulations

Make sure that the electrical installation meets local or nationally

applicable safety regulations.

ESD Guidelines

The media modules are equipped with electrostatically sensitive

components. These can be destroyed, or their life cycles reduced, by the

effects of an electrical field or by a charge equalization if the card is

touched.

For this reason, the cards are packaged in a conductive ESD protective

bag on delivery. The packaging can be reused.

Make sure you adhere to the following protection measures for

electrostatically endangered assemblies:

Create electrical equipotential bonding between yourself and your

environment, e.g. using a wristband, which you clamp to the basic

device (knurled screw of an interface card). When the power supply

cable is connected, the basic device is grounded via the power supply

connection.

Only now do you take the card out of the conductive bag.

Outside the basic device, only store the cards in a conductive ESD

protective bag.

ESD protective field equipment is available for the safe handling of

electrostatically endangered assemblies.

You can find more information about electrostaticically endangered

assemblies in DIN/IEC 47 (Sec) 1330; February 1994 Edition and DIN EN

100 015.

CE marking

The devices comply with the regulations contained in the following

European directive(s):

2004/108/EG

Directive of the European Parliament and the council for standardizing

the regulations of member states with regard to electromagnetic

compatibility.

8MACH 100

Release

07/10

2006/95/EG

Directive of the European Parliament and the council for standardizing the

regulations of member states with regard to electrical equipment to be

used within specific voltage ranges.

In accordance with the above-named EU directive(s), the EU conformity

declaration will be at the disposal of the relevant authorities at the

following address:

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Tel.: +49 1805 141538

The product can be used in living areas (living area, place of business,

small business) and in industrial areas.

Interference immunity: EN 61000-6-2:2005

Emitted interference: EN 55022:2006 + A1:2007 Class A

Safety: EN 60950-1:2006

Warning!

This is a class A device. This device can cause interference in

living areas, and in this case the operator may be required to

take appropriate measures.

The assembly guidelines provided in these instructions must be

strictly adhered to in order to observe the EMC threshold values.

FCC note:

This device complies with part 15 of the FCC rules.

Operation is subject to the following two conditions:

This device may not cause harmful interference, and

this device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to

radiocommunications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be required

to correct the interference at his own expense.

MACH 100

Release

07/10 9

Recycling note

After usage, this product must be disposed of properly as electronic

waste, in accordance with the current disposal regulations of your county,

state and country.

10 MACH 100

Release

07/10

About this manual

The following manuals are available as PDF files on the CD-ROM supplied:

Installation user manual

Basic Configuration user manual

Redundancy Configuration user manual

Web-based Interface reference guide

Command Line Interface user manual

The Network Management Software HiVision/Industrial HiVision provides

you with additional options for smooth configuration and monitoring:

Configuration of multiple devices simultaneously.

Graphical interface with network layouts.

Auto-topology discovery.

Event log.

Event handling.

Client / Server structure.

Browser interface

ActiveX control for SCADA integration

SNMP/OPC gateway

Legend

The symbols used in this manual have the following meanings:

Listing

Work step

Subheading

This manual suits for next models

Table of contents

Other Belden Switch manuals

Belden

Belden grass valley SIRIUS 800 Series User guide

Belden

Belden HIRSCHMANN RSP20 User manual

Belden

Belden HIRSCHMANN MACH 4000 Series User manual

Belden

Belden Telecast Fiber Systems THOR-SLG User manual

Belden

Belden lumberg automation 0960 IOL 3816-001 User manual

Belden

Belden Hirschmann SPIDER II 8TX User manual

Belden

Belden HIRSCHMANN SPIDER II 16TX EEC User manual

Belden

Belden Hirschmann DRAGON MACH Series User manual

Belden

Belden HIRSCHMANN GRS105 User manual

Belden

Belden Hirschmann MACH1000 Series User manual

Belden

Belden Hirschmann SPIDER-SL-20-08T1999999SY9HHHH User manual

Belden

Belden Hirschmann MICE MS20 User manual

Belden

Belden Hirschmann MACH4002 Series User manual

Belden

Belden HIRSCHMANN Dragon PTN CSM310-A User manual

Belden

Belden HIRSCHMANN MACH4002-48+4G User manual

Belden

Belden Hirschmann HiOS-2S User manual

Belden

Belden Hirschmann SPIDER 8TX EEC User manual

Belden

Belden grass valley MASTERPIECE 12G-SDI User manual

Belden

Belden Hirschmann RS20 U Series User manual

Belden

Belden Hirschmann Rail Switch Power Lite User manual

Belden

Belden HIRSCHMANN PTN-CSM310-A User manual

Belden

Belden HIRSCHMANN Octopus II User manual

Belden

Belden Hirschmann IT MAMMUTHUS MTS26 Series User manual

Belden

Belden HIRSCHMANN HiOS-2A User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual