Behringer K-2 User manual

page 1 of 2

985-40000-01088 Rev.A

2021-02-03

Condential, for internal use only. Not to be reproduced.

Analog and Semi-Modular Synthesizer with

Dual VCOs, Ring Modulator, External

Signal Processor, 16-Voice Poly Chain and

Eurorack Format

Synthesizers and Samplers

K-2

User Support Bulletin

Calibration Procedure

Set the K-2 controls as shown.

Make sure your K-2 has been powered on for more than 30 minutes, and that it is in a place where the temperature will

not change drastically while performing the calibration.

Follow all steps in the order in which they are presented.

Introduction

The unit is carefully calibrated at the factory. The performance may change over time or due to environmental changes,

and the following recalibration procedures can be used to bring it back to its factory settings.

page 2 of 2

985-40000-01088 Rev.A

2021-02-03

Condential, for internal use only. Not to be reproduced.

page 2 of 2

Condential, for internal use only. Not to be reproduced.

Music Tribe accepts no liability for any loss which may be suered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein.

Technical specications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik,

Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Oberheim, Auratone and Coolaudio are trademarks or registered trademarks of Music Tribe Global

Synthesizers and Samplers

K-2

VCO PITCH Calibration

Press and hold “TRIG SW” while powering up to enter the testing mode. (In this mode, the ON LED will blink yellow).

The K-2 has an internal calibration routine to calibrate the pitch of the VCO.

Press and hold “TRIG SW,” and then set the “FILTER1/2” switch. The ON LED will light yellow, indicating that the

VCO calibration has begun.

Wait until the ON LED changes color:

- Green indicates that the calibration was successful.

- Red indicates calibration failure. If this occurs, turn o the power and repeat from Step1.

Restart the unit.

End of Procedure

Table of contents

Other Behringer Synthesizer manuals

Behringer

Behringer SYSTEM 15 User manual

Behringer

Behringer SYSTEM 55 User manual

Behringer

Behringer UB-Xa User manual

Behringer

Behringer D A-440 Installation instructions

Behringer

Behringer PRO-1 User manual

Behringer

Behringer 110 VCO/VCF/VCA User manual

Behringer

Behringer 914 Fixed Filter Bank User manual

Behringer

Behringer PRO-1 User manual

Behringer

Behringer POLY D User manual

Behringer

Behringer CRAVE User manual

Behringer

Behringer MS-1 User manual

Behringer

Behringer DEEPMIND 12 User manual

Behringer

Behringer SYSTEM 55 User manual

Behringer

Behringer NEUTRON User manual

Behringer

Behringer MODEL D User manual

Behringer

Behringer TORO User manual

Behringer

Behringer 110 VCO/VCF/VCA User manual

Behringer

Behringer DEEPMIND 12 User manual

Behringer

Behringer WASP DELUXE User manual

Behringer

Behringer POLY D User manual

Behringer

Behringer DEEPMIND 12 User manual

Behringer

Behringer PRO-800 User manual

Behringer

Behringer MS-1-BK Manual

Behringer

Behringer DeepMind 6 User manual

Popular Synthesizer manuals by other brands

Kawai

Kawai MP7 Software update

Joranalogue

Joranalogue Contour 1 user manual

Full Bucket Music

Full Bucket Music Mono/Fury manual

Kawai

Kawai PH50 owner's manual

IK Multimedia

IK Multimedia UNO Synth PRO X user manual

Roland

Roland Gaia SH-01 Quick guidebook

Roland

Roland GR-30 manual

Gotharman

Gotharman Gotharman's anAmoNo-box user manual

Yamaha

Yamaha DX21 owner's manual

QuStream

QuStream HDFS-550 Technical manual

Modal Electronics

Modal Electronics ARGON8 quick start guide

Roland

Roland GS-500 instructions

Octave

Octave Cat SRM Service manual

Dreadbox

Dreadbox Murmux Initiate manual

neutral labs

neutral labs ELMYRA 2 Build guide

Waldorf

Waldorf KYRA user manual

Tubbutec

Tubbutec Juno-66 user manual

EFM

EFM VCADSR - 3510 manual