Beacon BSSK-1 User manual

OWNER'S

MANUAL

Revised 06-99 24-126-101

Ergonomic Solutions

Contents

Safety Precautions ........................................... 1

Receiving Instructions ...................................... 1

Installation Instructions .................................. 1-2

Warranty............................................................1

SAFETY PRECAUTIONS

Read owner's manual completely before operating unit!

•Keep hands, feet and foreign objects out from

underneath lift

• Never crawl under lift

RECEIVING INSTRUCTIONS

Every unit is thoroughly tested and inspected prior to

shipment. However, it is possible that the unit may incur

damage during transit. If damage is noticed when unloading,

make a note of it on the BILL OF LADING. Remove all

packing and strapping material, then inspect the unit again for

damage.

IF DAMAGE IS EVIDENT, FILE A CLAIM WITH

THE CARRIER IMMEDIATELY!

Finally, check the design

specifications to ensure they match those as requested (i.e.

table size, control type, motor voltage, etc...)

INSTALLATION INSTRUCTIONS

STEP 1 - Unpack accordion skirt kit carefully. Avoid bending

the aluminum extrusions and rods.

STEP 2 - Refer to Figure 2 at the right. Thread the rope top

of the accordion skirt (1) into the aluminum extrusions (2).

STEP 3 - Place the accordion skirt, with the extrusions

installed, over the deck of the scissor table as shown in

Figure 1.

STEP 4 - Attach aluminum extrusions to sides of Lift Table.

Carefully line up holes in aluminum extrusion with holes in

side of Lift Table. Secure extrusion to table using 5/16" self-

tapping screws (3).

STEP 5 - Insert stiffener rods into accordion skirt. Locate ¼"

holes in ends of

BLACK

convolutions of accordion skirt.

Carefully insert stiffener rod into hole, taking care not to rip or

damage the skirt.

WARRANTY

This product is warranted for one year from date of

purchase to be free of manufacturing defects in material and

workmanship. The manufacturer's obligation hereunder is

limited to repairing such products during the warranty period,

provided the product is sent prepaid back to the factory.

This warranty does not cover normal wear of parts or

damage resulting from any of the following: negligent use or

misuse of the product, use or application contrary to installa-

tion instructions, or disassembly, repair or alteration by any

person prior to authorization from a factory representative.

FIGURE 1

FIGURE 2

INSTALLATION INSTRUCTIONS

FOR LIFT & TILT SCISSOR TABLE

STEP 1 - Unpack accordion skirt kit carefully. Avoid bending

the aluminum extrusions and rods.

STEP 2 - Refer to Figure 1 at the right. Install steel angles

(1) on sides of deck frame using the predrilled holes (2) and

the self tapping screws (3) provided.

STEP 3 - Refer to Figure 2 at the right. Thread the rope top

of the accordion skirt (4) into the aluminum extrusions (5)

taking care to match lengths. Identify the two longer sides of

the accordion skirt by the amount of exposure at each end of

the aluminum extrusions.

STEP 4 - Place the accordion skirt with extrusions installed

around the unit as shown in Figure 3. The skirt will rest on

the previously installed angles.

STEP 5 - Attach aluminum extrusions to sides of Lift Table.

Carefully line up holes in aluminum extrusion with holes in

side of Lift Table. Secure extrusion to table using 5/16" self-

tapping screws.

STEP 6 - Insert stiffener rods into accordion skirt. Locate ¼"

holes in ends of

BLACK

convolutions of accordion skirt.

Carefully insert stiffener rod into hole, taking care not to rip or

damage the skirt.

INSTALLATION INSTRUCTIONS

FOR GROUND SCISSOR LIFT

STEP 1 - Unpack accordion skirt kit carefully. Avoid bending

the aluminum extrusions and rods.

STEP 2 - Refer to Figure 1 at the right. Attach steel angle

back support (4) to the Lift Table using the 3/8"-16 x 1½" bolts,

3/8" flat washers and 3/8" lock nuts. Make sure steel angle

back support is attached to Lift Table before proceeding on to

the next step. NOTE: Steel angle back support should be

firmly attached -

DO NOT OVERTIGHTEN NUTS AND

BOLTS.

STEP 3 - Thread the rope top of the accordion skirt (1) into the

aluminum extrusions (2) taking care to match lengths.

STEP 4 - With the lift slightly elevated, place the accordion

skirt with extrusions installed around the unit as shown in

Figure 1.

STEP 5 - Attach aluminum extrusions to sides of Lift Table.

Carefully line up holes in aluminum extrusion with holes in side

of Lift Table. Secure extrusion to table using 5/16" self-

tapping screws (3).

STEP 6 - Insert stiffener rods into accordion skirt. Locate ¼"

holes in ends of

BLACK

convolutions of accordion skirt.

Carefully insert stiffener rod into hole, taking care not to rip or

damage the skirt.

FIGURE 1

(1) Accordion skirt with rope top

(2) Aluminum extrusion

(3) 5/16 x ½" self-tapping screw

(4) Steel angle back support

(5) Holes for mounting steel angle

FIGURE 1

FIGURE 3

FIGURE 2

This manual suits for next models

Other Beacon Lifting System manuals

Beacon

Beacon BCART-1500D-DC-CTD User manual

Popular Lifting System manuals by other brands

morse

morse 82H-124 Operator's manual

Braun

Braun NL955 Series Operator's manual

haacon

haacon 1889.10 quick start guide

Protekt

Protekt AT 252 instruction manual

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 operating manual

Nova Technology International, LLC

Nova Technology International, LLC NAS Series quick start guide

Genie

Genie Z-60/34 Operator's manual

Screen Technics

Screen Technics INTERFIT Vertical Up Lift instructions

Mortuary Lift

Mortuary Lift ULTIMATE 1000 instructions

Custom Equipment

Custom Equipment Hy-Brid 3 Series MAINTENANCE & TROUBLESHOOTING MANUAL

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Maintenance and troubleshooting manual

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 MAINTENANCE & TROUBLESHOOTING MANUAL

BERG

BERG BeNomic EasyLeaf Technical manual

Powermate

Powermate LiftGate LG-3 Installation & operation manual

Snorkel

Snorkel TM12 Series Operator's manual

Terberg

Terberg OMNIDEKA Translation of the original instructions

Harmar Mobility

Harmar Mobility AL625 Installation & owner's manual

Rotary

Rotary SPO16 installation instructions