BDI ARENA 9970 User manual
1
ARENA
9970
Your Arena Flat Panel Mount is engineered for easy
assembly. Carefully follow this procedure to prevent any
damage.
Placement and Maintenance
Arena Flat Panel Mount is designed for indoor use on level
floors. Clean steel parts with a moist cloth.
Step 1
Unpack and identify the components at left. The assembly
workspace should be a non-marring surface such as carpet.
For missing hardware pieces, please contact BDI Customer
concerns, please contact your BDI Retailer.
Step 2
Attach two Cabinet Mount Brackets (B) to rear-center
edge of cabinet’s Top and Bottom Panels using six (6) 5/16
x 5/8in Screws (C) and provided Allen Wrench (A).
Component List
A - 5mm Allen Wrench
x 1
B - Cabinet Mount
Brackets
x 2
Designed by BDI Design Studio.
These distinctive product configurations are protected by US and
international patents, trade dress, and/or copyright laws.
BDI is a trademark of Becker Designed, Inc. All Rights reserved.
©2009, BDI
Made in Taiwan. 062309v2
ASSEMBLY INSTRUCTIONS
BDIUSA.COM CUSTOMERSERVICE@BDIUSA.COM
B
C x 6
D - Spine x 1
G - Horizontal Mounting
Bracket
x 1
J - Vertical Mounting
Bracket
x 2
K - TV Mounting Kit
x 1
F - 5/16 x 1-3/4in
Screws
x 4
E - Swiveling Bracket
Assembly
x 2
H - 5/16 x 3/8in
Screws
x 4
I - Washer x 4
N - Jam Nut x 2
M - Leveling Disc x 2
C - 5/16 x 5/8in
Screws
x 10
2
ASSEMBLY INSTRUCTIONS
BDIUSA.COM CUSTOMERSERVICE@BDIUSA.COM
C x 4
Step 3
Attach Spine (D) onto Cabinet Mount Brackets (B)
then fasten securely into place using four (4) 5/16 x
5/8in Screws (C) and provided Allen Wrench (A).
NOTE: Mounting hole pattern can vary depending on
cabinet model. Select the four (4) hole pattern that
fits with the upper mounting slots and conceals them
below the top panel when viewed from cabinet front.
B
F
Step 4
Attach each Swiveling Bracket Assemby (E) to top
of Spine (D) with four (4) provided 5/16 x 1-3/4in
Screws (F) using Allen Wrench (A). Be sure to position
each Swiveling Bracket Assembly so that it aligns with
and inserts cleanly into the Spine (D) holes.
NOTE: There are several mounting-height positions
to choose from on 3” increments. In general,
for larger TV’s (54” – 60”) select a higher set of
mounting holes; on smaller TV’s (40”- 46”) select a
lower set of mounting holes.
Front Mount
F
Side Mount
3
ASSEMBLY INSTRUCTIONS
BDIUSA.COM CUSTOMERSERVICE@BDIUSA.COM
Front Mount
K
K
L
L
Side Mount
Front Mount Side Mount
NOTE: Selecting the ‘side-mount’ Spine location for the Swiveling
Brackets will position television close to rear of cabinet, but can
limit left-to-right swiveling. Selecting the ‘front-mount’ Spine
location will position television approx 1.5” closer to cabinet front
and will enable maximum left-to-right swiveling range.
Step 5
Attach Horizontal Mounting Bracket (G) to installed
Swiveling Bracket Assemblies (E) using four (4)
5/16 x 3/8 in Screws (H) and four (4) Washers (I)
with the provided Allen Wrench (A).
NOTE: Slots along Horizontal Mounting Bracket
(G) must be at BOTTOM. Be sure to position each
Swiveling Bracket Assembly (E) so that each sits
within recessed portion of the Horizontal Mounting
Bracket (G) (Circled below).
Recommended
2-person step
for easy
installation
4
ASSEMBLY INSTRUCTIONS
BDIUSA.COM CUSTOMERSERVICE@BDIUSA.COM
M
Step 7
With the help of another person, lift television with
installed Vertical Mounting Brackets (J) and lower
carefully onto Horizontal Mounting Bracket (G).
Step 6
Position each Vertical Mounting Bracket (J) on back
of TV and attach using mounting screws and spacers
(if required) provided in TV Mounting Kit (K). Each
bracket must align vertically with the other. Both can be
raised or lowered on back of TV at 1” increments.
Install Leveling Disc (M) onto
threaded posts of Vertical
Mounting Bracket (J).
Make sure the felt side is
facing out.
NOTE: Various mounting
screws are provided in TV
Mounting Kit (K), but some
TVs may require specific
hardware not provided by
BDI. In such cases, please
contact your TV manufacturer
to identify and source your
hardware.
M x 2
G
J
Recommended
2-person step
for safe
installation
K
5
ASSEMBLY INSTRUCTIONS
BDIUSA.COM CUSTOMERSERVICE@BDIUSA.COM
G
N
J
M
Step 7 (continue)
Level the TV using the Leveling Discs (M) near the
slots in the lower Horizontal Mounting Bracket (G).
Then secure into place using provided Jam Nut (N)
on exposed mounting stud until finger-tight.
Step 8
Use the open channel inside Spine (D) to organize
and route cabling to and from the TV.
Other BDI TV Mount manuals
