Basler Dart User manual

Basler dart

QUICK INSTALLATION GUIDE FOR

USB 3.0 CAMERAS

Document Number: AW001304

Version: 04 Language: 000 (English)

Release Date: 8 July 2015

All material in this publication is subject to change without notice and is copyright

Basler AG.

Basler provides the dart camera as a component which is designed to be

integrated into a system. Therefore, Basler dart cameras are delivered without

housing.

The system designer or system integrator is responsible for the compliance of the

final product to the local requirements and regulations valid in the country of use.

Contacting Basler Support Worldwide

Europe, Middle East, Africa

Basler AG

An der Strusbek 60–62

22926 Ahrensburg

Germany

Tel. +49 4102 463 515

Fax +49 4102 463 599

[email protected]

The Americas

Basler, Inc.

855 Springdale Drive, Suite 203

Exton, PA 19341

USA

Tel. +1 610 280 0171

Fax +1 610 280 7608

[email protected]

Asia-Pacific

Basler Asia Pte. Ltd.

35 Marsiling Industrial Road 3

#05–06

Singapore 739257

Tel. +65 6367 1355

Fax +65 6367 1255

[email protected]

www.baslerweb.com

Quick Installation Guide for Basler dart Cameras AW00130404000

iBasler dart

Table of Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

1.1 General Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.2 USB 3.0 Host Controller Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2 Installation Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

2.1 Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.1.1 Installing the Basler pylon Camera Software Suite . . . . . . . . . . . . . . . . . . . . . . 3

2.1.2 Installing the Host Controller Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.2 Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.2.1 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.2.2 Installing the Camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3 Using the USB Configurator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

4 Acquiring Your First Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

5 Next Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

AW00130404000 Quick Installation Guide for Basler dart Cameras

Basler dart 1

1 Introduction

The installation procedures in this guide assume that you want to get your Basler dart USB 3.0

camera operational as quickly and as simply as possible.

Depending on the dart camera variant, the installation procedures vary.

The following basic assumptions are made for all dart cameras:

That you will be using a PC equipped with one of the following operating systems:

That a USB 3.0 port is installed in your PC and your dart camera will be connected to it.

That your USB 3.0 host controller chipset is compatible with the dart USB 3.0 camera. For

recommendations, see Section 1.2 on page 2.

That you will be installing the Basler pylon Camera Software Suite on your computer.

That there is no previously installed pylon software on your PC.

If old pylon software is installed, uninstall it.

Windows 7 (32 bit) Windows 7 (64 bit)

Windows 8.x (32 bit) Windows 8.x (64 bit)

All Basler dart USB 3.0 cameras are USB 2.0 backward compatible. However,

functionality and data transmission rate of the camera will be limited if

connected to a USB 2.0 port.

For information about suitable USB 2.0 host controllers and about optimizing

the USB 2.0 data transmission rate, see the application note Recommended

USB 2.0 Host Controllers for Basler dart and pulse Cameras (AW001344). You

can download the document from the Basler website: www.baslerweb.com

Fig. 1: Basler dart Camera Variants

dart

CS-mount (*)

dart

bare board

dart

S-mount

*CS-mount color cameras are equipped with

an IR cut filter.

Quick Installation Guide for Basler dart Cameras AW00130404000

2Basler dart

1.1 General Preparations

The following items must be available before starting installation:

A Basler dart USB 3.0 camera. Three variants are available:

dart bare board,

dart CS-mount, and

dart S-mount.

If you want to use I/O signals: an I/O cable that meets the requirements indicated in the Basler

dart User’s Manual for USB 3.0 Cameras (AW0001305).

A USB 3.0 cable.

A PC with USB 3.0 port. The port can be realized via a mainboard-based host adapter or via a

separately installed host adapter card. For recommendations, see Section 1.2.

Internet access

If you have access to a storage device containing all required drivers, you do not need Internet

access.

Depending on the application you use the Basler dart camera in, you may also require the following

items:

Mounting devices

Cooling devices

A suitable lens.

Contact your Basler sales representative to order suitable cable assemblies.

1.2 USB 3.0 Host Controller

Recommendations

Basler recommends the following host controller chipsets as they work well with Basler USB 3.0

cameras:

Renesas USB 3.0 host controller chipsets

The Renesas chipsets are for example used on ASUS PCIE USB3 host adapters.

Intel Ivy bridge host controller chipsets.

Evaluations of other USB 3.0 host controller chipsets are continuously updated. Contact Basler

technical support for the latest information about other recommended chipsets.

For more information, see the USB 3.0 Host Controllers' Maximum Bandwidth Measurements

(AW001260) application note on the Basler website.

AW00130404000 Quick Installation Guide for Basler dart Cameras

Basler dart 3

2 Installation Procedures

2.1 Software Installation

2.1.1 Installing the Basler pylon Camera Software

Suite

1. If you have old Basler pylon software installed on your system, make sure to uninstall the

software. For more information about uninstalling Basler pylon software, see the Installation

and Setup Guide for Cameras Used with Basler pylon for Windows (AW000611).

2. Make sure all cameras are disconnected from your computer.

3. Download the appropriate installer from the Basler website (www.baslerweb.com) to a local

directory on your computer:

If you are using a 32-bit Windows operating system, download the installer

Basler pylon x86 x.x.x.xxxx.exe.

If you are using a 64-bit Windows operating system, download the installer

Basler pylon x64 x.x.x.xxxx.exe.

4. Close all open applications.

5. Launch the downloaded installer.

6. In the Setup Wizard, on the Welcome page, click Next.

7. On the License Agreement page, accept the agreement and click the Next button.

8. On the Customer Information page, enter the appropriate information and click the Next

button.

9. On the Destination Folder page, determine the directory where you want to install the

software to and click the Next button.

Before installing Basler pylon software, make sure the Windows Update service is

active. Otherwise, the Basler pylon software can’t be installed.

To install the Basler pylon Camera Software Suite:

You must use the Basler pylon 4.2 Camera Software Suite or later to operate

Basler dart USB 3.0 cameras.

Quick Installation Guide for Basler dart Cameras AW00130404000

4Basler dart

10. On the Custom Setup page, a list of program features is displayed.

a. Deselect the features of the pylon software that you do not want to install.

b. Only select those features of the pylon software you want to install.

The example shown below assumes that you install the 64-bit version of the Basler pylon

software, that you will only use USB 3.0 cameras, and that your applications and software

development only use C++.

11. Click the Next button.

12. On the Ready to Install the Program page, click the Install button.

13. On the Setup Wizard Completed page, click the Finish button.

The installation program has added shortcuts on the desktop for the pylon Viewer and the

pylon USB Configurator.

14. Check the installed software features:

Windows 7: Click Start > All Programs > Basler > pylon 4 Camera Software Suite.

Windows 8 or 8.1: Right-click on the bottom-left corner of the screen, then click Search to

open the Apps view. You can find the installed software features in the Basler group.

The Basler pylon software installation is complete.

The deselected software features will not be installed. However, if you want

you can easily install them later.

Before proceeding, close all applications needing a network connection.

Otherwise, the network connections for your applications will temporarily be

lost.

AW00130404000 Quick Installation Guide for Basler dart Cameras

Basler dart 5

2.1.2 Installing the Host Controller Driver

Installation Under Windows 7

’

1. Click Start > All Programs > Basler > pylon 4 Camera Software Suite >

Tools & Drivers > USB 3.0 Host Controller Drivers.

The USB 3.0 Host Controller folder opens showing the xHCI driver setup packages and a

Readme.txt file. The readme file includes information about the matching driver setup for each

variant of the Renesas host controller chipset.

2. Install the matching xHCI driver setup package for the Renesas host controller chipset.

If the host controller uses a Renesas µPD720200 or µPD70200A chipset:

a. Click Renesas-USB3-Host-Driver-21390-setup.exe to install the matching xHCI driver

setup package.

If the host controller uses a Renesas µPD720201 or µPD720202 chipset:

a. Click Renesas 3.0.23.0.zip to unpack the matching xHCI driver setup.

b. Click Renesas-USB3-Host-Driver-30230-setup.exe to install the matching xHCI driver

setup package.

The matching xHCI driver is installed.

Installation Under Windows 8 or 8.1

Use the xHCI driver that is included in the Windows 8 or Windows 8.1 operating system on your

PC. The xHCI driver is suitable for all brands of host controller chipsets for USB 3.0 ports. The driver

needs not explicitly be installed.

If you are using a USB 3.0 host controller with a

Renesas USB 3.0 chipset to operate your dart camera, follow the instructions

below.

non-Renesas USB 3.0 chipset to operate your dart camera, make sure to

obtain and install a compatible xHCI driver from the manufacturer. After driver

installation, proceed with the hardware installation in Section 2.2 on page 6.

To install a driver for host controllers using Renesas USB 3.0 chipsets:

If you are not sure which chipset is used, install both xHCI driver setup

packages that are delivered with the Basler pylon Camera Software Suite.

Quick Installation Guide for Basler dart Cameras AW00130404000

6Basler dart

2.2 Hardware Installation

2.2.1 Precautions

DANGER

Electric Shock Hazard

Non-approved power supplies may cause electric shock. Serious injury or death

may occur.

You must use a camera power supply which meets the Safety Extra Low

Voltage (SELV) and Limited Power Source (LPS) requirements.

If you use a powered hub as part of the USB 3.0 connection, you must use a

powered hub that meets the SELV and LPS requirements.

WARNING

Fire Hazard

Non-approved power supplies may cause fire and burns.

You must use a camera power supply which meets the Limited Power Source

(LPS) requirements.

If you use a powered hub as part of the USB 3.0 connection, you must use a

powered hub that meets the LPS requirements.

NOTICE

Dust on the sensor can impair the camera’s performance.

Every time you handle the camera without a lens attached, make sure that the camera is

pointing down so that no dust can reach the sensor.

If the camera is not installed, store it in its original packaging.

NOTICE

Heat can damage the camera.

Make sure that you provide sufficient heat dissipation to keep the operation temperature of the

device at the maximum value or below as specified for the camera during operation. For more

information about the temperature requirements and about providing heat dissipation, see the

Basler dart User’s Manual for USB 3.0 Cameras (AW0001305).

Table of contents

Other Basler Digital Camera manuals

Popular Digital Camera manuals by other brands

Mercury

Mercury 350K user manual

Pentax

Pentax Optio LS 465 operating manual

Sanyo

Sanyo VPC-S1085 instruction manual

GE SMART A1255 user manual

Point Grey

Point Grey Gazelle Getting started

Nikon

Nikon COOLPIX A Reference manual

Pentax

Pentax P-5 manual

BlazeVideo

BlazeVideo A280 instruction manual

Sony

Sony MCA-20 manual

Sony

Sony Alpha DSLR-A290 instruction manual

ATIK Cameras

ATIK Cameras One user manual

CohuHD Costar

CohuHD Costar 3930 Series Installation and operation manual

Leica

Leica M10-R quick start guide

FujiFilm

FujiFilm FinePix A700 owner's manual

Lorex

Lorex LNZ81P25 Series quick start guide

GE J1470S user manual

Sony

Sony A6700 Startup guide

Canon

Canon EOS ELAN7 instructions

Basler dart User manual

Popular Digital Camera manuals by other brands