Barry-Wehmiller Streamfeeder Value Series User manual
Manual
Value Series V-710IJ
Part Number: 00900367
© 2009 Thiele Technologies, Inc. - Streamfeeder. All rights reserved.
No part of this publication may be reproduced, photocopied, stored on
a retrieval system, or transmitted without the express written consent of
Thiele Technologies, Inc. - Streamfeeder.
Thiele Technologies, Inc. - Streamfeeder
103 Osborne Road
Minneapolis, MN 55432-3120 USA
Tel:763.502.0000
Fax:763.502.0100
e-Mail: service@streamfeeder.com
Web: www.streamfeeder.com
Printed in the USA.
i
Value SerieS V-710iJ Manual
Contents
Safety Information ........................................................ii
Specications ..............................................................iv
Section 1: About the Machine .......................................................1
Section2: InstallingtheMachine ..................................................5
Section3: PreparingforOperation ............................................. 11
Section4: HowtoOperate ...........................................................19
Section5: Troubleshooting .........................................................23
Section6: InspectionandCare ...................................................25
Section7: MechanicalComponents ...........................................31
Section8: ElectricalComponents...............................................46
ii Value SerieS V-710iJ Manual
Message
Conventions
DANGER signies an action or specic equipment area that can result
in serious injury or death if proper precautions are not taken.
WARNING signies an action or specic equipment area that can
result in personal injury if proper precautions are not taken.
CAUTION signies an action or specic equipment area that can
result in equipment damage if proper precautions are not taken.
ELECTRICAL DANGER signies an action or specic equipment
area that can result in personal injury or death from an electrical haz-
ard if proper precautions are not taken.
TIP signies information that is provided to help minimize problems
in the installation or operation of the feeder.
NOTE provides useful additional information that the installer or
operator should be aware of to perform a certain task.
CHECK signies an action that should be reviewed by the operator
before proceeding.
IMPORTANT alerts the installer or operator to actions that can poten-
tially lead to problems or equipment damage if instructions are not
followed properly.
WARNING LABELS afxed to this product signify an action or spe-
cic equipment area that can result in serious injury or death if proper
precautions are not taken.
Before You Begin
iii
Value SerieS V-710iJ Manual
Message
Conventions
Before You Begin
Avoid injury. Do not reach around guards.
Hazardous voltage. Contact will cause electric shock or burn. Turn off
and lock out power before servicing.
Moving parts can crush and cut. Keep guards in place. Lock out power
before servicing.
Pinch point. Keep hands and ngers clear.
Moving parts can crush and cut. Keep guards in place. Lock out power
before servicing.
iv Value SerieS V-710iJ Manual
Maximum Product Size: ........................ 12 W x 12 L in (305 x 305 mm)*
Minimum Product Size: ........................ 3.75 W x 3.75 L in (95 x 95 mm)
Optional: ................................................... 2.5 W x 2.5 L in (63 x 63 mm)
Min/Max Product Thickness: ....................... .003-.75 in (.076-19.1 mm)
Belt Speed: ................................................. 5700 in/min (144780 mm/min)
Electrical Requirements: ................................... 115/230vac, 50/60Hz, 3A
Weight: ............................................................................... 41 lbs. (18.6kg)
*Optional product size available
speCifiCations
1
Value SerieS V-710iJ Manual
1About the Machine
The V-710IJ Universal Friction Feeder is designed for reliability,
exibility, and ease of use with a variety of vacuum and non-vacuum
bases.
All parts required for setup, loading, feeding, and easy operator con-
trol are combined into one compact unit.
Review the main assemblies in Figure 1-1 to become familiar with
names and locations of feeder parts and adjustments. This will help to
prepare you for initial setup. Descriptions are found in Table 1-1.
Review the control panel components in Figure 1-2 to become fa-
miliar with names and locations of specic connectors, switches, and
controls. This will help to prepare you for installation and operation.
Descriptions are found in Table 1-2.
Figure 1-1. Main Assemblies of the V-710IJ Universal Friction Feeder
Features
Main Assemblies
•ACPowerCord
•SideGuides
•ExternalRunInputCord(Optional)
LoosePartsSupplied:
GateAssemblyand
Adjustment
TableTop
FeedBelts
BackWedgeandAdjustments
Hold-Down
Assembly
Discharge
Belts RaisedFeedBelts
Adjustment
SideGuides
2Value SerieS V-710iJ Manual
Feature Description
Gateassemblyandadjustment Mounted on a gate bracket assembly above the feed belts, this device
provides a curvature to help preshingle stacked material. When properly
adjusted, a clearance is created to help singulate and feed material.
Tabletop Used to support the back wedge.
Raisedfeedbeltsadjustment Located on each side of the feeder, these adjustment knobs allow you to
raise the rear feed belts above the table top to achieve optimum contact
with material.
Sideguideadjustments Dual-knob design allows you to move side guides together or apart for
different size material. Can be positioned equally or offset. (Note: Single-
knob design also available.)
Dischargesafetyshield Provides residual risk protection to operator when feeder is running.
Backwedgeandadjustments Lifts the material to keep it off the table top, reduces excessive contact
with the feed belts, and helps push the material against the curvature
of the gate assembly. To achieve proper lift, adjustment wing-nuts and
locking levers allow you to slide the wedge to various positions and
angles.
Feedbelts Provides the friction and motion necessary to pull individual material from
the bottom of the stack and through the gate assembly area.
Dischargebelts Combined with the top roller hold-down assembly, provides the friction and
motion necessary to transport material away from the gate assembly area.
Hold-downassembly A series of small rollers mounted on movable brackets help to gently hold
material down on the discharge belts as material exits the gate assembly
area. These brackets and rollers are part of the gate assembly and are
removed when the gate assembly is removed.
Controlpanelcomponents For descriptions, see Figure 1-2A and 1-2B, and Table 1-2.
ACpowercord,8ft.(2.44m) IEC320 removal three-prong. Shipped loose.
Externalruninput(optional) This two-wire cable allows the feeder to be turned On or Off with the host
base.
ProductDescription Section1
Table1-1. MainAssembliesFeatureDescriptions
3
Value SerieS V-710iJ Manual
Figure 1-2A. Control Panel Components (Left and Right Side Views)
ControlPanelComponents
Figure 1-2B. Control Panel Components (End View)
4Value SerieS V-710iJ Manual
Feature Description
Externalruninputconnector This 4-pin connector (labeled ExternalRunInput) is used to carry start/
stop signals from a vacuum or non-vacuum base to the feeder.
PowerOn/Off Toggles AC power On or Off.
Fuseholder Contains two replaceable 5-Amp, 5x20 mm time delay fuses.
IMPORTANT: Always make sure power module is replaced exactly as
removed so that “115” is always visible on 115V models and "230" is
always visible on 230V models. Failure to follow this caution can result in
damaged electrical parts.
ACpowercordsetconnector Cordset plugs into this IEC320 connector to provide feeder with power
from a grounded and fused outlet.
Modeswitch(optional) Note: Included with optional external run input only. This slide switch
(labeled Continuous/ExternalRun) allows you to use the feeder “stand-
alone” or with the optional external run input interface.
Variablespeedcontrol This dial switch (labeled Speed) allows the feeder speed to be
synchronized with a vacuum or non-vacuum base. Turning counter-
clockwise decreases speed; clockwise increases speed. Note: Feeder
motor stops if turned completely counter-clockwise.
Rundelay Used to delay (or synchronize) feeder startup with base startup. Range is
adjustable from 0 to 12 seconds.
Table1-2. ControlPanelFeatureDescriptions
(optional)
This manual suits for next models
1
Table of contents
Other Barry-Wehmiller Wire Feeder manuals
Popular Wire Feeder manuals by other brands
Lincoln Electric
Lincoln Electric LN-25X Operator's manual
Matrix
Matrix OmniFlow 330 Product instruction manual
EWM
EWM drive 4X IC D EX operating instructions
Lincoln Electric
Lincoln Electric 12442 Operator's manual
Aim
Aim AIVE Basic Manual
Lincoln Electric
Lincoln Electric Power Feed 10 Robotic K1780-2 Operator's manual
Miller
Miller XR-AlumaFeed Suitcase owner's manual
Lincoln Electric
Lincoln Electric Activ8X Operator's manual
Abicor Binzel
Abicor Binzel iROB Feed HA operating instructions
EWM
EWM drive 4X IC D EX operating instructions
Lincoln Electric
Lincoln Electric LF-72 Operator's manual
Hakko Electronics
Hakko Electronics 373 instruction manual