Barcus-Berry Breeze IV User manual
9. Install the output jack assembly to
the guitar using four of the wood
screws supplied and as show in the
illustration below.
10. Route the wire toward the preamp
opening using the supplied cable
clips to secure the cable inside
the body.
11. Likewise route the pickup cable
toward the preamp opening.
12. Install a battery into the preamp
(see owner’s manual) and verify the
operation of the unit.
CONNECT OUTPUT
JACK HERE
INSERT SADDLE
PICKUP JACK
HERE
MIC OR
CONTACT PICKUP
13. Insert the Breeze through the preamp
opening into the guitar to allow
cable connections to be made.
14. Firmly holding down the preamp
assembly in opening, Insert the
under-saddle pickup cable into
the preamp’s 2.5mm jack as shown
in the illustration.
15. In the same fashion, insert the output
connector into the 5-pin molex
connector. In the case of the Breeze
II, the mating connector has only
three pins. Mate this connector to
the middle three pins of the output
connector. This will leave one open
pin on either side of the jack.
16. If installing a Breeze IV system with
an auxiliary pickup, at this time
install the cable from this pickup
into the 3.5mm AUX jack, located
near the saddle pickup input.
17. Before attaching the trim plate and
preamp to the body of the guitar,
Confirm operation of the preamp by
plugging the guitar into an amp
or PA and testing all functions.
18. Finally, referring to the
illustration above, align the
preamp mounting tabs to the pilot
holes and use the four wood screws
provided to attach the preamp.
Insert the wood screws through the
preamp trim plate, mounting tabs,
and finally into the pilot holes.
Tighten until snug. The trim plate
will flex to adapt to the curve of
the guitar’s upper bout.
Notes:
Installation Guide
Barcus-Berry®
PO Box 63366, N Charleston, SC 29419 USA
www.barcusberry.com
Installation Guide
Barcus-Berry®
PO Box 63366, N Charleston, SC 29419 USA
www.barcusberry.com
Breeze Installation.indd 1 12/3/2009 11:35:18 AM
Preamp Installation
Barcus Berry highly recommends that
you choose a reputable guitar service
technician or luthier in your area to
install your new Breeze preamp into
your guitar. The installation procedure
involves modifications to your guitar
that require specialized skills to assure
satisfactory results. Bring this guide
to your technician since it describes
the proper steps for a successful
installation.
Two openings along with mounting screw
pilot holes must be made on the guitar to
allow proper securement of the preamp
system to the guitar. Refer to the figure
below. In addition, resizing of the saddle
slot may be required along with different
shim dimensions.
The preamp body is mounted on the side
of the guitar’s upper bout. Though the
preamp’s escutcheon is capable of
adapting to the curves found on this part
of the guitar, make sure that the upper
bout’s arc radius is greater than 4-3/4”
(120mm) to insure a nice finish.
The output jack assembly is mounted on
the lower bout, on the treble side near
the tail block. The Breeze IV requires
a rectangular cut out and mounting
holes while the Breeze II mounts with a
conventional end pin jack.
The procedure for installation is as
follows:
1. Before deciding on the final
locations for each of these preamp
components, check the construction
details of the guitar to assure
adequate clearances required for
preamp fit.
2. Then, using the templates provided
below, mark the openings to be
made as well as the mounting pilot
holes as shown. Please note that
the Breeze II end pin jack simply
requires a 15/32”hole through the
R a d.= 2.0
[T Y P I C A L ]
Dia.= 2.0
75.778.8
71.7
20.0
42.0
55.0
[m m ] [m m ] [m m ]
[m m ]
[m m ]
[m m ]
[m m ]
[m m ]
[T Y P I C A L ]
V E R T I C A L D I M E N S I O N S M AY V A R Y
±1 M M D U E T O D I F F E R E N C E S I N
U P P E R B O U T R A D I I
1 7/8
2 1/16
Rad. = 5/64
1 5/16
5/64
[TYPICAL]
[TYPICAL]
[TYPICAL]
[TYPICAL]
Dia. = 5/64
[52mm]
[48mm]
[34mm]
[33mm]
1 11/32
1/16
[1.5mm]
[2mm]
[2mm]
[2mm]
tail block and generally replaces
the strap knob often located in that
position.
3. Check component fit and make
adjustments as necessary.
4. Next, if necessary, adjust the size of
the saddle slot to accommodate the
dimensions of piezo pickup supplied.
See figure below.
5. Drill a 1/8”hole through the bass end
of the saddle slot and elongate to
5/16”to allow routing of the pickup
cable through the top.
6. Mount the pickup by routing the
cable though the hole in the top and
setting it in the slot.
7. The pickup should fit snugly, but
should be removable.
8. Adjust the saddle slot if necessary
to attain a good fit and install
shims, if necessary, to bring the
saddle height to specification.
PREAMP
OUTPUT
3"
1/8"
5/16"
PICKUP CABLE HOLE
5/16"
SHIM FOR PROPER
SETUP
PDF Created with deskPDF PDF Writer - Trial :: http://www.docudesk.com
\
TOWARD END
BLOCK
Breeze Installation.indd 2 12/3/2009 11:35:19 AM
This manual suits for next models
1
Other Barcus-Berry Amplifier manuals
