Barco UDX R9008600 User manual

R5906116 /00

UDX

Quick Start Guide

Install Lens !! ONLY USE TLD+ Zoom Lenses !!

1. Place the primary lens lock in “unlock” position. Handle (ref. 1) towards electrical socket (ref. 3).

2. If present remove the plastic protection cover from the lens holder opening.

3. Check if the secondary lens lock stands in the “unlock” position (ref. 2) .

3. Gently insert the lens. Ensure the lens connector matches the electrical socket on the lens holder.

4. Insert the lens until the connector seats into the socket.

- The secondary lens lock (ref. 2) makes an audible clicking sound when latching.

- Do not release the lens yet, keep pushing the lens against the front plate!

5. Secure the lens in the lens holder by sliding the primary lens lock handle into the “locked” position.

6. Check if the lens touches the front plate of the Lens Holder.

7. Check if the lens is really secured by trying to pull the lens out of the lens holder.

Connect power

Ensure that the power is properly connected to the powerinput.

(120-160V* / 200-240V [+/-10%, * reduced light output] )

Download Product Manual

Product manuals and documentation are available online at www.barco.com/td/R9008600

Registration may be required; follow the instructions given on the website.

IMPORTANT!

Read Installation Instructions before connecting equipment to the mains power supply.

- 2 -

2. Orientation of the unit is set as standard in table front projection mode.

Change the projector set up in the ALIGNMENT > ORIENTATION menu.

3. For Advanced adustments like Warping, Light management, etc. see User Guide of the projector.

Adjust

1. Adjust the lens settings by pressing the LENS button or via the direct lens keys on the RCU.

Select the “Greenfocus” test pattern to adjust the lens.

TIP: Press star button (*)

to activate test pattern

Connect and Select source

1. Connectavailable sourcesto the appropriate inputports.

2. Select connected source: Image of selected inputappears.

- The LED of the selected source lit up GREEN.

- The yellow LED indicates if sync/signal is present.

Startup

1. Power on. Turn the mains switch to on ( I ).

- Start up sequence starts. Backlight of the Power on/off button flashes WHITE.

- When start up sequence is finalized the Power on/off button lit WHITE.

2. Press the Power on/off button.

- The backlight of the Power on/off button changes from WHITE to BLUE.

- Local LCD displays a start up screen.

- 3 -

Switch off

1. Press the Power on/off button for three seconds.

2. Wait until the after-cooling cycle is finished (approximately 30 sec.)

3. Turn the mains switch to off (’0’).

4. Unplug the power cord from the projector.

321

30 s

3 s

Local Keypad

1MenuNavigation.

2MenuSelection.

3Open Menu.

4MenuBack.

5Power On/Off.

6OSD On/Off.

7InputSelection.

8Shutter Open/Close.

9Test Patterns.

10 Lens Menu.

11 Touch Panel.

1 2 3 4 5 6

1011 9 8 7

• Remove the lens before transporting the projector.

• First switch the projector to Standby mode and wait until After Cooling is

finished to switch off the main power.

• Ensure the projector is operating with clean filters.

• Do not block the ventilation in and outlets.

• External laser light can cause severe damage to the DMD. This damage is

not covered by warranty.

Precautions

- 4 -

RCU buttons

1Button pressed indicator.

14 Test pattern Lens Menu

13 Numeric buttons.

2Shutter Open.

15 XLR connector.

3Shutter Close.

17 Macro button.

16 TBD.

4Touch Panel On/Off.

18 MenuBack.

5LCD On/Off.

19 Defaultbutton.

6Lens Zoom.

20 Lens Focus.

7Lens Shift.

21 Color On/Off.

8Menu Activation.

22 Test Patterns.

9Menu Selection.

23 Power On.

10 Menu Navigation.

24 Power Off.

11 Input Selection.

25 Stereo Jack.

12 Address button.

26 RCU On/Off.

- 5 -

Communication Panel

321 4 5 6 7 8 9 10 11 12 13

1WiFi antenna for wireless IP (optional) 8RS232 for serial communication

212V 1A output 9Sync Out 3D

3Firmware update/USB backup custom settings 10 Sync In 3D

410/100 base-T for external control over IP and Art-Net 11 Status lights

5DMX interface input 12 IR receive sensor

6DMX interface output 13 GSM antenna input (optional)

7XLR input for wired projector control

Venues & Hospitality Input (V&H)

SELSELSELSELSELSELSEL

TUO/NIIDSNIIDS

SEL

SYNC

DP HDMI

SYNC

HDBT 1

SYNC

HDBT 2

SYNCSYNC

1 2 3 4 5 6 7 8

1Quad 3G SDI channel A Input 5DisplayPort Input

2Quad 3G SDI channel B Input 6HDMI Input

3Quad 3G SDI channel C Input/Output 7HDBaseT Input 1

4Quad 3G SDI channel D Input/Output 8HDBaseT Input 2

Virtual & Augmented Reality Input (V&AR) (Optional)

SELSELSELSEL

DP A DP B DP C DP D

SYNCSYNCSYNCSYNC

1 2 3 4

1Quad DisplayPort channel A Input 3Quad DisplayPort channel C Input

2Quad DisplayPort channel B Input 4Quad DisplayPort channel D Input

- 6 -

Button Backlight Status

Button Color status Description

Projector starts up (Booting)Blinking WHITE

Projector is in StandbySolid WHITE

Blinking RED Error condition

Blinking BLUE Projectorgoes to ON mode

Projector is ON

Power button

Solid BLUE

Off Projector not in power ON state

Solid WHITE Shutter is open

Shutter is closedSolid RED

Shutter button

LED Status

LED Color status Description

Off Projector powers up

Projector is in StandbyRED

Projector is ReadyORANGE

PWR (power LED)

GREEN Projector is on

Light source is offOff

Light source not detectedRED

Light source is on in ECO mode

ORANGE

GREEN Light source is on in normal mode

LIGHT (Illumination LED)

Light source is on in CLO modeGREEN-ORANGE

Off No error

RED toggleson/off Error

ERR (error LED)

ORANGE toggleson/off Warning

IR signal receivedREDIR

GREEN IR signal acknowledged

Support

Website www.barco.com/esupport

- USA +1 866 374 7878

- EMEA +32 56 36 8019

- APAC +86 400 88 22726

Tel.:

Table of contents

Popular Projector manuals by other brands

iEmmet

iEmmet MP-312 user manual

Epson

Epson VS400 Specifications

Sony

Sony VPL-HS10 Marketing Specifications & Features manual

Sony

Sony VPL-HW65ES Quick reference manual

Toshiba

Toshiba TLP-791U Specifications

Philips

Philips LC1341 Declaration of conformity

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB operating instructions

NEC

NEC NP600S EDU Specifications

BenQ

BenQ SH753P user manual

Eiki

Eiki EK-623U series quick start guide

Epson

Epson PowerLite Pro Cinema 6020UB user guide

Epson

Epson PowerLite Home Cinema 705HD user guide

Christie

Christie LHD700 user manual

Navitar

Navitar FX instruction manual

InFocus

InFocus LitePro 560 user guide

Sony

Sony SRX-R815P operating instructions

Vivitar

Vivitar DP1500 X specification

Acer

Acer C20 Series manual