Axis Happy H32 Manual
Happy 1
Happy Reserve System
PILOT'S MANUAL
Thank you for taking the time to read this booklet.
Happy 2
CONTENTS
1. Introduction
2. Pre flight
3. Care and maintenance
4. Storage
5. Drying and airing
6. Cleaning
7. Repacking
7.1 repacking sequence
8. Warranty
9. Repairs
10. About Axis
Happy 3
1. INTRODUCTION
Axis have a 10 year history in parachute design and have employed their years of knowledge
and expertise in the design and construction of the paragliding reserve system, Happy.
Happy reserve consists of: canopy with lines, inner container, connecting bridle strap and
release handle.
Happy is based on the pull-down apex design. The canopy is reinforced so that it is resistant
even to the dynamic impact after a free fall. The pull-down apex central line reduces opening
time and improves the sink rate whilst the inner container is designed so that all the
suspension lines are attached to container by rubber bands so there is no danger of
entanglement of lines or canopy during deployment.
Happy is designed only for use in an emergency situation on a paraglider, it is unsuitable for
free fall parachuting.
This manual provides information about the Happy reserve system, which will help you to fly
safely and keep your equipment in good condition. If after reading this manual you have any
further questions, please don’t hesitate to contact us or any authorised Axis dealer.
Thank you for choosing the Happy from Axis.
www.axispara.cz
www.axispara.co.uk
Happy 4
2. PRE FLIGHT
For your safety, always use a consistent system of pre-flight checks for all your equipment and
repeat the same sequence before every flight.
Specifically with your reserve parachute, check that:
There is no visible damage that could affect its airworthiness.
The reserve parachute container is closed correctly with the pin or pins in place.
The deployment handle is secured correctly to your harness
If any part of your harness / reserve/ handle system includes Velcro, you should separate and
re-attach these pieces regularly. Velcro ‘beds-in’ over time which could make deploying your
reserve difficult,
3. CARE AND MAINTENANCE
We recommend that Happy should be inspected and repacked at least every 6 months by a
trained professional re-packer. If you feel there may be the likelihood of damage or wear,
additional inspections should be carried out.
After a deployment, the reserve must be checked by the distributor or manufacturer.
The materials used in Happy have been carefully selected for maximum durability.
Nevertheless, maintaining your reserve following the guidelines below will extend its lifetime.
It is recommended that any reserve system is replaced after 10 years, even if it has never been
used.
4. STORAGE
Due to the specific purpose of the reserve system you should pay careful attention to its
storage and packing. If you need to store your reserve long-term it should be unpacked and
loosely rolled in a closed bag.
Be careful to avoid any possible contact with harmful substances such as oils, grease, acids,
paint etc. Your reserve should always be stored away from contact with UV radiation
(sunlight).
5. DRYING AND AIRING
If your reserve gets wet you should remove it from the harness, dry it naturally in the air, and
have it repacked before putting it back into the container. Take care to avoid contact by
sunlight while the reserve is drying. If the canopy shows any sign of mildew or mould, it must
be sent to the distributor or manufacturer for checking, as its strength could be
compromised.
Happy 5
6. CLEANING
Oils, grease, paint and other chemicals can seriously damage and weaken the structure of
reserve system.
If your reserve becomes contaminated by any such agent the whole reserve system must be
sent back to the manufacturer for a thorough inspection.
A dirty reserve canopy or container can be cleaned with lukewarm water. Mild, neutral soap
may be used on the container if necessary.
Always rinse the canopy thoroughly in fresh, clean water and allow it to dry naturally.
7. REPACKING
We recommend that you open, air and repack the reserve at three monthly intervals as
recommended in the warranty.
Before each repack, a thorough inspection must be made of the following:
the canopy fabric must be checked for any damage or pollution from chemicals or dirt
the suspension lines must be checked for any damage
each attachment point between the suspension lines and canopy must be checked.
the inner and outer container, deployment handle, webbing connection with harness
(bridle) and reserve pin system must be checked for damage
If any damage is evident during this inspection you should send the whole reserve system to
the manufacturer for repair.
Please be aware that the reliability of any reserve parachute system is significantly affected by
how it is packed. We strongly recommend that you only use only trained qualified re-packers
or the manufacturer for this important task.
You should always have the reserve system inspected by the manufacturer in the event of any
of the following:
After deploying the reserve, even in controlled or training purposes
After any damage or alteration of the system
Within 2 years of the previous manufacturers inspection.
Failure to do so may invalidate the warranty.
The warranty card should be sent with the reserve system at each inspection.
Happy 6
7.1 Repack sequence
Repacking should be carried out in a clean, smooth dry place.
Before starting make sure you have the following available to hand,
Rubber bands
Solid weights ( clean and smooth )
Take hold of the apex lines and check that they are the same length. Secure the apex lines with a weight
or attach them to a fixed object at each end to help keep the reserve in place.
Separate the lines equally each side of the apex lines.
Happy 7
Locate the centre panels by following the outer suspension line. Begin by folding all the panels one by
one to the same side of the suspension lines. Check each panel for any damage or deterioration of the
fabric and /or seams while doing this. Check that each panel is flat and without creases.
Next fold each panel one by one to the other side of the suspension lines. Again check each panel for
damage and make sure it is flat and without creases.
Happy 8
Next fold back half the number of panels.
Make sure that each panel is laid flat and evenly and without any creases.
Keep the skirt even and suspension lines separated each side of the apex lines.
Happy 9
Pull down the apex into the reserve by stretching all the suspension lines to the same length while
gently holding onto the apex of the reserve
Happy 10
S-Folding:
Fold 1/3 of the canopy over the right side and then back over itself. Then fold the right side over the left
and back over itself. Make sure that you secure the canopy while making the folds to prevent creasing.
Smooth the canopy to remove excess air and make sure that the skirt remains even.
Accordion-Folding:
Take hold of the skirt and fold the canopy underneath it to a size that fits the deployment bag. Holding
this securely, continue to fold the rest of the canopy in an accordion fashion over the folded skirt.
This manual suits for next models
1
Table of contents
Other Axis Aircraft manuals
