AVProConnect AC-EX40-444-KIT User manual
AC-EX40-444-KIT
AVProConnect
3518 N Casco Avenue ~ Sioux Falls, SD 57104
1-877-886-5112 ~ 605-274-6055
support@avproconnect.com
AC-EX40-444-KIT
Ultra Slim 40m (70m HD) 4K60 4:4:4, HDR
HDBaseT Extender Audio Extraction, EDID
Management, Scaling
pg. 1
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
AVProConnect presents its first 18Gbps over CAT extender. Using ICT (Invisible Compression
Technology) we have achieved what was thought to be impossible. The AC-Ex40-444
delivers a virtually lossless, high bandwidth, 4K HDR signal with support for any signals up to
18Gbps.
AC-EX40-444-KIT
Key benefits of using AC-EX40-444:
Invisible Compression Technology:
ICT is a revolution in HDMI extension technology.
This proprietary technology can compress high bandwidth HDMI signals into a
manageable size in order to fit through a CAT Cable "pipe". The ICT algorithm can
manage all flavors of HDR including 4:4:4, 4:2:2, and 4:2:0 as well as signals up to
18Gbps and 4K 60Hz 4:4:4. The architecture of ICT allows it to be compatible with all
chroma subsampling types, color spaces and HDMI Deep Color up to 12-Bit. Our
technology is unique because it is truly invisible. It is not only invisible to the human eye,
it is invisible to HDMI test gear and other sink devices. With the AC-EX40-444 what
comes in is what goes out. What makes ICT special is the ability to preserve HDR
Metadata, color information and depth in its full, original, integrity. Other compression
technologies sacrifice color information and depth to save space. This will cause very
visible banding, color shifting and motion artifacts in the image.
Down Scaling:
The AC-EX40-444 has a scaling circuit built into the transmitter. The
scaler can scale down 4K (and HDR) --> 1080P. This extender can be used to scale down
where you need to without reducing the entire system. For example, there may be a
system with 4K distribution, but there may be one or two displays that are older. You
don't have to compromise signal with the ability to downscale!. The AC-EX40-444 does
the heavy lifting, eliminating the need to add additional boxes. This is an ideal choice for
extension on projects requiring an 18Gbps matrix like the AC-MX1616-AUHD.
Total EDID Management:
The AC-EX40-444 has robust EDID control. EDID
management allows control of the input device and the ability to request specific video
resolutions and/or audio codecs.
On Board Troubleshooting:
This unit allows generation of a 1080P or 4K test pattern
in order to identify external problems (source, repeater, displays, etc...). Be sure that
your wiring is correct and get to the bottom of problems quickly should they arise,
without having to worry if the source or sink is working properly. A test pattern may be
generated from the TX or the RX so the total system infrastructure can be verified.
Cascade:
AC-EX40-444 features HDMI signal equalization and amplification. This allows
for a “daisy chain” of AC-EX40-444 extenders for extremely long distance transmission.
With our unique bi-directional power, there is no need for a power source where the Rx
and Tx meet up in a daisy chain, simply power the first Tx and the second Rx. Power will
be provided to the middle remotely.
IR & RS232 Management:
IR & RS-232 are bi-directional and can control the sources
from the sinks or vice versa.
pg. 2
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
Long Range Extender w/ Ethernet, EDID & Control
AC-EX40-444-KIT
■Product Overview
■Model Numbers:
•AC-EX40-444-T ~ HDBaseT Transmitter w/ Audio Extraction, IR,
RS-232, EDID, Bi-Directional PoE and Scaler
•AC-EX40-444-R ~ HDBaseT Receiver w/ IR, RS-232, Bi-Directional
PoE
■Features
•HDMI 2.0(a/b)
•18Gbps Bandwidth Support (Using ICT)
•Ultra Slim (.47 inch/12mm)
•Up to 4K60 4:4:4 Support
•Full HDR Support (HDR 10 & 12 Bit)
•HDR, HDR10+ and HLG Support
•4K --> 1080P Down-scaling for mixed systems
•EDID Management and EDID emulate
•4K & HD Test Patterns built-in to Tx and Rx for troubleshooting
•L/R Audio Extraction on Tx and Rx
•HDCP 2.2 (and all earlier versions supported)
•CEC Pass Through
•3D Support
•70M (230ft) on 1080P (Cat6a)
•Up to 40m (131ft) on 4K (up to 4K60 4:4:4, HDR) (Cat6a)
•Bi-directional 48v PoH (Power Over HDBaseT, only one Power
Supply Needed)
•I-Pass feature for control system "pass-through"
•3-20v protection circuit built-in for safe IR transport
•Bi-Directional RS-232 transport
•LED Status, Link, Power indication lights
•Use single UTP/STP LAN cable (CAT-5E/6A) with substitute
HDMI cable to achieve long distance transmission.
•Supports uncompressed PCM 2- Ch., LPCM 5.1 & 7.1, Dolby
Digital, DTS, Dolby TrueHD, DTS HD-Master Audio, Atmos
•ESD protection circuitry (Inputs & Outputs) to 7KV
•Ability to cascade
pg. 3
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
Notice
AVProConnect reserves all rights to make changes in the hardware,
packaging and any accompanying documentation without prior written notice.
Warning
To reduce the risk of fire, electric shock or product damage:
Basic
6. Clean this device with
a dry cloth only.
1. Do not expose this device to
rain, moisture, dripping or
splashing and ensure that
objects filled with liquids are
not placed on or near the devices.
2. Do not install or place this unit
in a bookcase, built-in cabinet or
in another confined space.
Ensure the unit is well ventilated.
3. To prevent risk of electric
shock or fire hazard due to
overheating, do not obstruct
the unit’s ventilation openings
with newspapers, tablecloths,
curtains, and similar items.
4. Do not install near any heat
sources such as radiators, heat
registers, stoves, or other
apparatus (including amplifiers)
that produce heat.
5. Do not place sources of naked
flames, such as lighted candles,
on the unit.
7. Unplug this device
during lightning storms or
when unused for long
periods of time.
8. Protect the power cord
from being walked on or
pinched particularly at
plugs.
9. Only use attachments /
accessories specified by
the manufacturer.
10. Refer all servicing to
qualified service
personnel.
AC-EX40-444-KIT
pg. 4
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
■What's Included
AC-EX40-444-KIT
Whats in the box?
•AC-EX40-444-T (Transmitter)
•AC-EX40-444-R (Receiver)
•48V Power Supply (One supplied)
•1x IR Tx Unit
•1x IR Rx Unit
•4x 3 Pin Terminal blocks for Audio and RS232 Ports
•Mounting Ears
•Operating Instructions
*Optional 3Pin to Stereo Audio Cables available for purchase
pg. 5
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
AC-EX40-444-KIT
■Specifications
pg. 6
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
AC-EX40-444-KIT
■The Transmitter
Back
Front
HDBaseT IR Mode
RS232
L/R Out (PCM Only) HDMI In Micro USB
(Firmware)
IR Out IR In
Indicator Troubleshooting
Lights on the Transmitter:
POWER - On the back by power supply input: (Red) This is an indicator that the power is connected. There
are only two states for light:
•Light Is On = Power supply is connected and functioning
•Light Is Off = Power supply is not connected or there is no power present. (In order to have power: check
the power supply, USP, Outlet, etc...)
*LED also flashes when using the settings button described below.
STATUS - On front by HDMI Port: (Blue) This indicator shows that the HDMI source is connected. The
states are:
•Light Is On (Solid) = Sync w/ HDMI source is correct and solid.
•Light Is Flashing = The light flashes during the sync process. If it is flashing continuously, a picture may
not be present.
If the BLUE HDMI STATUS LIGHT is flashing, check the following:
1. The source. Plug it directly into the display to be sure it's functioning properly.
2. Try a longer HDMI cable. Some HDMI cables do not sync well at shorter lengths.
3. Set the EDID to state #1 (See below).
4. If these do not work, enable the "Test Pattern" (See Below). If you see the pattern, the problem is between
the source and the Transmitter, please try a different source.
5. Contact AVProConnect if these suggestions do not work.
pg. 7
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
Indicator Troubleshooting
Lights on the Transmitter cont.:
LINK - Above RJ45 (HDBT) Port: (Green) This indicator shows that the AV HDBT link between the TX and
RX is in tact. This light should ALWAYS be solid. If this light is flashing or not present attempt following:
1. Check the length. The maximum distances are 40m (131ft) on 4K and 70m (230ft) on 1080P.
2. Remove any coils of cable and make sure that there is not excess cabling.
3. Bypass all patch panels and punch-down blocks.
4. Re-terminate connectors. Sometimes, even if a cable tester indicates the run is valid, something may be
just slightly off.
5. Contact AVProConnect if these suggestions do not work.
STATUS- Above RJ45 (HDBT) Port: (Amber) This is an indicator showing that the power is present
between the Transmitter and Receiver. This light ALWAYS BLINKS steadily indicating everything is OK. If you
do not see this light, attempt the following:
1. Check the length. The maximum distances are 40m (131ft) on 4K and 70m (230ft) on 1080P.
2. Remove any coils of cable and make sure that there is not excess cabling.
3. Bypass all patch panels and punch-down blocks.
4. Re-terminate connectors. Sometimes, even if a cable tester indicates the run is valid, something may be
just slightly off.
5. Try powering from the Receiver instead of the Transmitter (See Receiver page for more about PoE
direction)
6. Contact AVProConnect if these steps do not work.
pg. 8
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
AC-EX40-444-KIT
Functions & Setup of the Transmitter:
IR Mode Slide Switch:
(On Back) This is used to select a preferred IR Mode:
IR-EYE - The IR Input will be configured to operate with an IR Receiver Eye.
I-PASS - The IR Input will be configured to safely operate with a direct connection from a control system
using a mono or stereo 3.5mm cable. This is protected from 3v-20v. Default mode is IR-EYE.
Using the Setting Button:
(On Back) The setting button can be pressed in different combinations based on
what is needed. The status light on the front will flash based on the selection. The selections are in series,
meaning, for example, if you are on selection 5 (listed below), you can come back later and press it again to
move you to 6, 7, 8, 1, 2, etc... An ink pen is best to press the button.
The POWER LED is the indicator LED.
EDID Management:
Quick press to select EDID
1. EDID BYPASS --- LED Flashes 1 Time (Default, from downstream device)
2. 1080P_2CH --- LED Flashes 2 Times
3. 1080P_8CH --- LED Flashes 3 Times
4. 4K60HzY420_3D_2CH --- LED Flashes 4 Times
5. 4K60HzY420_3D_8CH --- LED Flashes 5 Times
6. 4K60Hz_3D_2CH_HDR--- LED Flashes 6 Times
7. 4K60Hz_3D_8CH_HDR --- LED Flashes 7 Times
8. USER EDID --- LED Flashes 8 Times
While in the USER EDID state (8), press and hold the setting button (for 4 seconds) tin order to copy the EDID
from the connected display or downstream device to the user EDID and it will apply automatically.
Why do this?
This is commonly used there is a need for a specific, known EDID that the installer may prefer. It can also be
used if you want to bypass an EDID of an AVR or another connected device. (IE, Plug the extender kit directly
into a display and COPY the EDID. Plug it back into an AVR that may not have a current/good EDID).
Scaler Setting:
While in ANY state besides the USER EDID state, press and hold the setting button (for 4 seconds) to toggle
the scaler mode. The options are:
1. Normal Mode(ICT Mode) --- LED Flashes 1 Time
2. Down Scaler Mode (4K->2K) --- LED Flashes 2 Times
pg. 9
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
AC-EX40-444-KIT
Functions & Setup
of the Transmitter Cont.:
Test Pattern Generator:
Press and hold the setting button (for 4 seconds) while powering up the transmitter. You should see the
color bar pattern to the right on screen. When in this mode, you can quick press to toggle the resolution.
Quick press the setting button---Select the test pattern timing
•1080P --- LED Flashes 1 Time (3 sets of color bars)
•4K --- LED Flashes 2 Times (5 sets of color bars)
This can be useful for checking your cabling and helping for
troubleshooting. You can make sure that your are OK for distance
based on the resolution as well.
pg. 10
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
AC-EX40-444-KIT
Table of contents
Other AVProConnect Extender manuals
AVProConnect
AVProConnect AC-EX100-UHD-T User manual
AVProConnect
AVProConnect AC-EX70-UHD User manual
AVProConnect
AVProConnect AVPro Edge AVP-AC-EX40-444-KIT User manual
AVProConnect
AVProConnect AC-EX70-UHD-KIT User manual
AVProConnect
AVProConnect AC-EX70-444-KIT User manual
AVProConnect
AVProConnect AC-AUDEX-DIGI User manual
AVProConnect
AVProConnect AC-EX70-UHD User manual
