Avocent DSR Series DSR1020 User manual
The following instructions will help you
to connect your DSR switch.
Should you require further assistance, please
consult your installer/user guide.
Check our web site at www.avocent.com/support to search the knowledge base or use the online request.
Avocent, the Avocent logo, The Power of Being There and DSR are registered trademarks of Avocent Corporation. All other marks are the property of their respective owners. ©2004 Avocent Corporation. All rights reserved. 590-420-603A
The Power of Being There
To connect a DSR switch
Quick Installation Guide
DSR®Switch
DSR1020 | DSR2020 | DSR4020 | DSR8020
Connecting power to the
DSR switch
Power down all servers that will be part of your DSR
switching system. Locate the power cord that came
with the DSR switch. Plug one end into the power
socket on the rear of the DSR switch. Plug the other
end into an appropriate AC wall outlet.
Connecting the local port
Plug your VGA monitor, PS/2 or USB keyboard and
mouse cables into the appropriately labeled DSR ports.
Connecting a DSRIQ module to
the DSR switch
Choose an available port on the rear of your DSR
switch. Plug one end of a CAT 5 cable (4-pair, up to
10 meters) into a numbered port and plug the other
end into the RJ-45 connector of a DSRIQ module.
Connecting a server to the
DSRIQ module
Plug the DSRIQ module into the appropriate ports on
the back of the server. Repeat this procedure for all
servers that are to be connected to the DSR switch.
Connecting network and
remote users
Plug a CAT 5 cable from your Ethernet network into
the LAN connector on the back of your DSR switch.
Network users will access the DSR switch through
this port.
(Continued on reverse side)
1
2
4
5
3
Plug in the
keyboard,
monitor and
mouse for your
local connection.
Server
SPC Power
Control Device
Local
Connections
Server
Server
Server
Modem
Connect your
SPC device to
the target servers.
Plug in the
external modem.
Connect the switch
to the network.
Connect DSRIQ
modules to the
DSR switch.
Power up target
servers and then
the DSR switch.
Connect servers
to the DSRIQ
modules.
Power down all
servers and attach
the appropriate
power cord to the
DSR switch.
2
7
13
5
6
8
4
DSR Switch
1357
2468
91113
10 12 14
15
16
A1
Telephone
network
Ethernet
The following instructions will help you
to connect your DSR switch.
Should you require further assistance, please
consult your installer/user guide.
Connecting an external
modem (optional)
The DSR switch may also be accessed using an
ITU V.92, V.90 or V.34-compatible modem. Plug one
end of a 9-pin serial cable into the MODEM connector
on the back of your DSR switch. Plug the other end
into the connector on the back of the modem.
NOTE: Using a modem connection instead of a
LAN connection will limit the performance capability
of your DSR switch.
Connecting the SPC device to the
DSR switch (optional)
Plug one end of the cable supplied with the SPC
power control device into the SPC connector on the
DSR switch and plug the other end into the SPC
device. Plug the power cords from the target servers
into the SPC power outlets. Plug the SPC device
into an appropriate AC wall outlet.
Powering up targets and switch
Power up each target server and then power up the
DSR switch.
For additional information
For further instructions on DSR switch connection,
software setup and security configuration, please
refer to the installer/user guide included with the
switch. Check http://register.avocent.com for the
latest DSR software and firmware updates.
The Power of Being There
To connect a DSR switch
(continued from reverse side)
Quick Installation Guide
DSR®Switch
DSR1020 | DSR2020 | DSR4020 | DSR8020
6
7
8
Check our web site at www.avocent.com/support to search the knowledge base or use the online request.
Avocent, the Avocent logo, The Power of Being There and DSR are registered trademarks of Avocent Corporation. All other marks are the property of their respective owners. ©2004 Avocent Corporation. All rights reserved.
Plug in the
keyboard,
monitor and
mouse for your
local connection.
Server
SPC Power
Control Device
Local
Connections
Server
Server
Server
Modem
Connect your
SPC device to
the target servers.
Plug in the
external modem.
Connect the switch
to the network.
Connect DSRIQ
modules to the
DSR switch.
Power up target
servers and then
the DSR switch.
Connect servers
to the DSRIQ
modules.
Power down all
servers and attach
the appropriate
power cord to the
DSR switch.
2
7
13
5
6
8
4
DSR Switch
1357
2468
91113
10 12 14
15
16
A1
Telephone
network
Ethernet
1357
2468
91113
10 12 14
15
16
A1
The Power of Being There
1357
2468
91113
10 12 14
15
16
A1
The Power of Being There
2
7
13
5
6
8
4
1357
2468
91113
10 12 14
15
16
A1
The Power of Being There
2
7
13
5
6
8
4
1357
2468
91113
10 12 14
15
16
A1
The Power of Being There
1357
2468
91113
10 12 14
15
16
A1
The Power of Being There
1357
2468
91113
10 12 14
15
16
A1
The Power of Being There
Other manuals for DSR Series DSR1020
11
This manual suits for next models
4
Other Avocent Switch manuals
Avocent
Avocent AutoView 3100 Installation and maintenance instructions
Avocent
Avocent AutoView 2020 User manual
Avocent
Avocent DSR Series DSR4160 User manual
Avocent
Avocent SwitchView IP 1020 User manual
Avocent
Avocent OutLook 1160ES Installation and maintenance instructions
Avocent
Avocent AMX5020 Installation and maintenance instructions
Avocent
Avocent SwitchView User manual
Avocent
Avocent Outlook 180DX Installation and maintenance instructions
Avocent
Avocent SwitchView 100 User manual
Avocent
Avocent 115B Installation and maintenance instructions
Avocent
Avocent SwitchView SC100 User manual
Avocent
Avocent SWITCHVIEW OSD - Operation manual
Avocent
Avocent AutoView 1000R Installation and maintenance instructions
Avocent
Avocent AMWorks User manual
Avocent
Avocent DSR4010 User manual
Avocent
Avocent DS1800 User manual
Avocent
Avocent AMX5000 User manual
Avocent
Avocent SwitchView User manual
Avocent
Avocent DSRTM 1021 Installation and maintenance instructions
Avocent
Avocent DSR Series DSR2161 User manual
