AVer M70Wv2 User manual

M70Wv2

Instruction Manual |安裝指南

取扱説明書| Bedienungsanleitung

Mode d'emploi | Manual de instrucciones

Manuale d'uso

English……..……………………………………………………….…......1

繁體中文……………………………………………………………….…24

日本語…..……………………………..……………………………….…46

Deutsch.............................................................................................61

Français…………………………………………………..………....…....83

Español...……………………………………………..……….…….….105

Italiano..........…………………………….….……………..……….…..127

English-1

Package Contents

M70Wv2*

Power Adaptor

Power cord**

Remote controller

AAA Battery (x2)

USB Cable

Quick Start Guide

Warranty card

(Europe, Japan,

Taiwan only)

2nd Wi-Fi Dongle

*The M70Wv2 comes with a pre-installed Wi-Fi dongle.

**The power cord will vary depending on the standard power outlet of the country where it is sold.

Optional Accessories

Carrying Bag

Anti-glare Sheet

Microscope Adapter

( 28mm and 34mm Rubber Coupler are included)

English-2

Parts Info

789

1. Camera head

2. LED lamp

3. Arm

4. IR sensor

5. Control panel

6. Handle

7. Built-in mic

8. Battery indicator

9. USB mini port

10. USB port

11. Wi-Fi dongle

12. Kensington lock

13. HDMI input

14. HDMI output

15. DC power jack

Compound Key

Reset to factory default settings.

With each press, cycle through the following resolutions:

Auto detection (4K, 720P, 1080P)

1024x768 (in supported HDMI device)

4K 60Hz (in supported HDMI device)

With each press, cycle through Normal, Motion, High quality, Microscope, Infinity,

and Marco modes.

English-3

Remote Control

Control Panel

Name

Function

1. POWER

Turn the camera on or off.

2. Wi-Fi/USB

Switch between Wi-Fi and USB modes.

3. CAPTURE

Capture still image in Camera mode. In

continuous capture mode, press this button

again to stop.

4. FREEZE

Freeze live images.

5. ROTATE

Rotate the image by 0/180°in Camera

mode.

6. INFO/

Press to view system information and battery

power status.

7. ▲,▼,◄, & ►

Pan and zoom-in image in live streaming.

8. AUTO FOC

Adjust the focus automatically.

9. ZOOM +/-

Increase/decrease the image magnification

in camera mode.

10. ZOOM 1X

Reset zoom level to 100%.

11. MUTE

Set the volume to mute.

12. CAMERA / PC

Switch the video signal between camera and

computer from the HDMI Input port

13. RECORD

Start/Stop audio & video recording. Video

recording can only be saved in a USB flash

drive.

14. RESOULTION

Press to switch between following modes:

- Auto detects the best resolution(4K, 720P,

1080P)

- 1024x768 (in supported HDMI device)

- 4K 60Hz (in supported HDMI device)

15. AE LOCK

Lock the exposure to stop M70Wv2

attempting to find optimal exposure.

16. LAMP

Turn the overhead light on/off.

17. DEL

Delete the selected picture/video in

Playback mode.

18. MODE

Press to switch between Normal, High

frame, and High quality, Microscope, Infinity,

or Marco mode.

19.

Make a selection.

20. VOLUME +/-

Adjust the volume.

21. BRIGHTNESS

+/-

Adjust the brightness.

22. RESET +/-

Reset to factory default setting.

23. Wi-Fi Indicator

Wi-Fi status indicator: Refer to <LED

Indicator>.

English-4

LED Indicator

Name

Status indicator

Power

Solid green: Power on

No light: Power off

Solid red: Standby (Camera is connected to power but not

in operation.)

Battery

Solid green(x3): Battery is full(100%-60%)

Solid green(x2): Battery is 60%-30%

Solid green(x1): Battery is 30%-5%

Solid red (x1): Battery is 5%-0%

Flashing red (x1): Battery is out of power

Solid orange(x3): Battery is abnormal

Wi-Fi

Solid blue: AP Mode Ready / STA connected

Slow flashing blue: Software connection with camera

Short flashing blue: Create AP mode / STA connecting

Solid green: Miracast mode ready

Slow flashing green: Miracast streaming start

Quick flashing green: Miracast device scan / connecting

[Note]

The battery will be exhausted for long-term usage. Do not replace the battery yourself. Please contact

your dealer.

P/N: 300AU8D0-EA9

English-5

Device Connection

Charge Your Camera

Your camera comes with a built-in battery. Before using it for the first time, charge it for at least 3 hours.

Connect to a power outlet using the included power adapter and power cord.

3 flashing green lights: Charging

3 solid green lights: Charged

You can also use a computer to charge your camera.

- Your camera must not be in operation. A solid red light on the power button indicates that it is in

Standby mode.

- Connect the included USB cable to the mini USB port on the camera and connect the other end

to a USB port on a computer. Charging with a computer will be slower.

If your camera is frozen, press +to restart.

English-6

USB Connection

Connect to a computer using the included USB cable to work with video conferencing software.

You can also plug in a USB flash drive to save images and videos. Press the Capture button to capture

images and the Record button to record videos.

English-7

HDMI Connection

1. By connecting a computer to the HDMI in port and a monitor or projector to the HDMI out port,

images and videos from the computer can be projected.

2. Press the Camera/PC button to switch between camera input and computer input.

English-8

Peer-to-Peer (P2P) Connection via Wi-Fi Dongle

(Windows only)

Method 1

1. Download and install AVerTouch software to your computer from AVer Download Center.

(https://www.aver.com/download-center).

Do not connect your camera to a computer with the included USB cable.

2. Press the Wi-Fi button to turn on Wi-Fi mode. The Wi-Fi indicator will be solid blue.

3. Plug in the second Wi-Fi dongle to your computer.

Your camera comes with 2 Wi-Fi dongles, one pre-installed in the camera. If you don’t find a

second dongle, it may be an optional accessory in your region or country. Contact your local

reseller.

Other manuals for M70Wv2

Table of contents

Languages:

AVer M70Wv2 User manual

Popular Document Camera manuals by other brands