Avaya ERS4826GTS Manual

Ethernet Switch

Setup

for Q-SYS

Avaya ERS4850 Series (Models ERS4826GTS, ERS4826GTS-PWR+, ERS4850GTS,

and ERS4850GTS-PWR+)

Revision 1.1—21 January 2016

Firmware used: 5.8.0.1 Software used: v5.8.1.029

Configuring the Switch

Assign an IP address, enable the optional web interface, and assign

QoS

1. Using a standard network switch console or “rollover” cable, connect the serial port on the

PC, or a USB-to-serial adapter, to the console port on the front of the switch.

2. Open a terminal emulator such as HyperTerminal or PuTTY and connect to the switch

using the following serial settings: 9600, N, 8, 1; no flow control.

If the switch does not respond by initiating a terminal session, try turning it off and on again.

As the switch boots up, the terminal emulator window should start displaying log

messages.

3. When the AVAYA logo appears, it will also display a status area indicating the switch

model, hardware version, firmware version, and the software version.

4. Press

Ctrl+Y

. A prompt showing the switch model number will appear—for example,

4850GTS-PWR+>

will appear. (Other models will display accordingly; for this setup guide,

we will use the 4850GTS-PWR+ as an example.)

5. Type enable and then press

Enter

6. The prompt will change to

4850GTS-PWR+#

Type

configure terminal

and press

Enter

7. The message “Enter configuration commands, one per line. End with CNTL/Z.” will appear,

followed by the configuration-mode prompt,

4850GTS-PWR+(config)#

The next step is to configure the switch’s intended IP address and subnet. Type

ip address xxx.xxx.xxx.xxx yyy.yyy.yyy.yyy

(where “xxx.xxx.xxx.xxx” is the intended IP address and “yyy.yyy.yyy.yyy” is the intended

subnet mask) and then press

Enter

Note: If the switch will reside in a part of the network that is inaccessible to the computer

except through a gateway, you must add the gateway’s IP address to this command. (This

is not a common situation.) In this case, you would type

ip address xxx.xxx.xxx.xxx yyy.yyy.yyy.yyy zzz.zzz.zzz.zzz

(where zzz.zzz.zzz.zzz is the optional gateway address) and then press

Enter

8. Enabling the web interface is optional. To do so, type

web-server enable

and press

Enter

9. Next, set the QoS parameters for Q-LAN audio and PTP packets with the following sets of

commands (you may copy and paste from the text below):

At the prompt, type

qos traffic-profile classifier name "QLAN_Audio" addr-type ipv4

ds-field 34 protocol 17 dst-port-min 6517 dst-port-max 7030

update-dscp 46 update-1p 6 eval-order 1 drop-out-action enable

and then press

Enter

Next, type

qos traffic-profile classifier name "QLAN_PTP" addr-type ipv4

ds-field 46 protocol 17 dst-port-min 319 dst-port-max 320

update-dscp 46 update-1p 6 eval-order 1 drop-out-action enable

and then press

Enter

10. The next step is to add traffic profiles to individual ports that host Q-LAN devices, so their

data packets are steered into Avaya’s “Premium Queue.” QSC recommends not applying

these profiles to ports that belong to other VLANs, so it often would not be appropriate to

apply them to the entire switch. If a port uplinks to another Avaya switch, for example, it is

better to let them honor their own IP precedence. In the commands below substitute the

port number or numbers where it says “port number(s)”; use a hyphen to designate a range

of port numbers, such as “1-3” for 1 through 3.

At the prompt, type

qos traffic-profile set port port number(s) name "QLAN_Audio" track-

statistics aggregate

and then press

Enter

Then type

qos traffic-profile set port port number(s) name "QLAN_PTP"

track-statistics aggregate

and press

Enter

11. Configuration is done. So exit configuration mode and save the settings with these

commands.

At the prompt, press

Ctrl+Z

(or type

exit

and then press

Enter

Next, type

save config

(or write mem)

and press

Enter

12. The switch is now correctly configured to properly prioritize Q-SYS traffic in an Avaya

enterprise QoS environment.

Notes: How to set the switch to factory default configuration

If you have “Enable” access:

1. At the prompt, type

and then press

Enter

2. Type

boot default

and press

Enter

3. At the question

Reboot the unit(s) (y/n)?

press

4. The switch will reboot with the factory default settings. This may take a couple minutes.

If you do not have your credentials or have lost them:

1. Connect the computer to the switch’s console port, using settings 9600, 8, N, 1. Open

your terminal emulation program.

2. Turn the switch off and on again to reboot it.

3. When the first line of the diagnostic tests appears, press

Ctrl+C

4. A menu will appear listing a number of options. Press

to initialize the switch and load its

default settings into its configuration.

5. Then press

to run the Agent code, which will complete the initialization and automatically

reboot the switch.

This manual suits for next models

Table of contents

Other Avaya Network Router manuals

Avaya

Avaya Secure Router 4134 Manual

Avaya

Avaya ERS 4926GTS User manual

Avaya

Avaya NN48500-598 User manual

Avaya

Avaya ERS 3500 Series User manual

Avaya

Avaya 4000 Series User manual

Avaya

Avaya ERS 3510GT-PWR+ User manual

Avaya

Avaya 5900 Series Instruction Manual

Avaya

Avaya 9000 Series User manual

Avaya

Avaya 8300 Series Quick guide

Avaya

Avaya ERS 8800 series User manual

Avaya

Avaya ERS 5510 User manual

Avaya

Avaya Secure Router 4134 User manual

Avaya

Avaya 3600 Series How to use

Avaya

Avaya ERS 4500 User manual

Avaya

Avaya P134G2 User manual

Avaya

Avaya 8800 Series Technical manual

Avaya

Avaya 5600 Series User manual

Avaya

Avaya ERS 8600 User manual

Avaya

Avaya 8600 Quick start guide

Avaya

Avaya VSP 4850GTS Series Instruction Manual

Avaya

Avaya P333R-LB Operator's manual

Avaya

Avaya Ethernet Routing Switch 8300 Series Technical manual

Avaya

Avaya ERS 4826GTS Instruction Manual

Avaya

Avaya 3500 series Operating instructions

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

TP-Link

TP-Link TD-8817 QIG

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

Cisco

Cisco NCS 540 Hardware installation guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

Cisco

Cisco ASR 1000 Series Installation and configuration guide

EnGenius

EnGenius ESR-9710 quick start guide

Cisco

Cisco 805 Series Product overview