3
www.automationdirect.com
1 - 8 0 0 - 6 3 3 - 0 4 0 5
6. Apply Power to the Monitor & PC
• Press the DISPLAY POWER button on the rear of the monitor to wake the
monitor up. Pressing the DISPLAY POWER button again turns off the
backlight inverter an puts the monitor in a re uce power state but
the touch screen remains active. It is important to note that this switch
oes not isconnect power from the monitor. Power is always supplie
to the internal AC/DC power supply, which in turn continually supplies
power to the internal monitor electronics an the optional touch screen
controller.
7. Install the Appropriate Touch Screen Driver
• The calibration of the touch screen occurs by a calibration utility that
installs as part of the touch screen river installation process.
• Applies to touch screen version only.
• Insert the Documentation an Driver CD into the host PC’s CD rive.
• If the CD oes not start automatically with the win ow shown below
isplaye , then go to Start > Run, browse to the CD’s “atlas.exe” file,
open it, an click OK.
• From the Atlas screen, the user can view the Har ware User’s Gui e for
the monitor being use , an /or install the touch screen rivers for the
particular PC operating system being use . Before installing the rivers,
please rea the Touch Screen Driver Documentation for operating
system etails.
• Reboot the PC an restart the monitor to activate the river.
• For the latest rivers go to:
http://support.automation irect.com/pro ucts/atlas.html
8. Verify Video and Touch Screen Functionality
• Verify the monitor’s vi eo isplay by running a familiar program.
• If using the touch screen mo el, use the touch screen to navigate by
running a familiar program.
Display Power
Button
Power
Indicator
DISPLAY POWER
WARNING
Touch Screen is still
active while display
power is off
LCD Power Button:
MAIN MENU
BRIGHTNESS/CONTRAST
1280X1024 63.9KHZ/60HZ
COLOR
POSITION
SETUP
EXIT
R G B
OSD Settings Main Menu:
9. Adjust the Monitor OSD Settings as equired
• Press the Select (Auto A j) control button on the rear of the panel to
initiate an automatic configuration of the screen.
• Although normally not nee e , the control buttons on the rear of panel
can be use to make other a justments to the screen.
• Consult the Har ware User’s Gui e, ATM-USER, on the supplie
Documentation an Driver CD for etaile usage of the OSD settings.
10. Installation Complete
WARNING: he monitor does not automatically select a video input
mode. he user must press the “UP (VGA/DVI)” button on the rear
of the monitor to select either VGA or DVI input. If a “No Video”
message appears on the screen, it is also suggested the user try using
the “UP (VGA/DVI)” button to select the active video input.
NOTE:ONCE YOU HAVE CONNECTED YOUR PC AND THE MONITOR,
SE ECTED THE VIDEO SOURCE, AND POWERED BOTH UNITS, IT IS
SUGGESTED THAT THE “SE ECT (AUTO ADJ)” BUTTON ON THE REAR
OF THE MONITOR BE PRESSED TO MAXIMIZE THE VIDEO SETTINGS.
5. Connect Power to the Monitor
• Power source nee s to be 100 - 240 VAC, 50/60 Hz.
• See power connection iagram to the right.
• Secure plug retention screws to monitor.
• Power shoul not be applie until all cables are attache an the
monitor is rea y to operate.
TOP VIEW
FRONT VIEW
ADC P.N. ATM-AC-CON or
PHOENIX CONTACT P.N. 1777992
LN
Plug Retention Screws
Power
Connection
Label
PE
WARNING: Damage can occur if power is not properly connected.
Power Connections:
100 VAC - 240 VAC INPUT (1.0 Amps Min)
PIN N . Definiti n
1 AC Line Input
2 AC Neutral Return
3 Protective Earth Ground
P nel Power Dr w
ATM1500 (T) 25 W
ATM1700 (T) 30 W
ATM1900 (T) 35 W
WARNING - EXPLOSION HAZARD - Do not disconnect equipment while
the circuit is live unless the area is known to be free of ignitable
concentrations.
Warning - Explosion Hazard - Substition of any components may
impair suitability for Class 1, Division 2.
Required Wire Specific tion
Wire Size 18 - 12 AWG (0.8 - 3.3 mm2)
Wire Material and
Temperature 60 °C or 60 / 75 °C Copper
Tightening T rque 7.0 lb·in (0.79 Nm)
WARNING – ouch screen is still active while display power is off.
A EN ION – L'écran tactile est toujours actif, méme quand l'af-
ficheur n'est pas alimenté.
ADVER ENCIA – La pantalla táctil sigue activa aún cuando el dis-
play esté apagado.
WARNUNG – ouch screen ist immer noch aktiv, während die
anzeigefläche ausgeschaltet ist.
