AUTLED LC-012-000 User manual

LED RF & DMX WiFi Interface Ethernet - User Manual

Item no: LC-012-000

1. Product Description

The RF & DMX Wiﬁ Interface Ethernet works with RF-receiver series or DMX 512 decoders to be

controlled by iOS or Android system via WiFi. With the interface you can control via WIFI

upto 8 different zones.

2. Speciﬁcation

Operation Voltage: 12VDC included in the set, via RF or DMX signal,

Operation Frequenz 2.4G

Dimensions: 110 x 85 x 24,2mm

3. Function/Introduction

green LED indicator:

Power on

red LED indicator:

data transfer activ

blue LED indicator:

WiFi connection activ

4. User Manual

There are three methods to connect the interface:

1. Connect your cell phone or tablet with the home net router (WiFi-RF)

2. Connect your cell phone or tablet with the convertor (WiFi-RF)

3. Connect you cell phone with your home net router (WiFi-DMX512)

DMX512 signal

output

12VDC power input

Ethernet

GND

D+

D-

Method 1: Connect your cell phone or tablet with the home net router (WiFi-RF)

reset button:

press and hold for

10 seconds - reset to

factory settings / clear all

connections

12VDC power input

Router

Method 2: Connect your cell phone or tablet with the convertor (WiFi-RF)

Method 3: Connect you cell phone with your home net router (WiFi-DMX512)

12VDC power input

Router

Installation of the „Easylighting“ APP:

1. Download the application app „Easylighting“ on your smartphone or tablet

or scanning on of the below two QR Codes (Android or IOS System) to download

the necessary APP:

2. If the convertor has connected with router, then connect your cell phone to your router network.

If the convertor did not connect with router, then connect your cell phone to the convertor network

directly (password: 0123456789 - as per interface backside)

3. Open the easylighting application and operating according the application manual.

1. The product shall be installedc and serviced by a qualiﬁed person.

2. Please avoid directly sun and rain/wet conditions.

3. Always be sure to mount this unit in an area with proper ventilation to avoid overhaeting.

4. Please check if the output voltage of any LED power supplies used comply with the working

voltage of the product.

5. Never connect any cables while power is on and always assure correct connections to avoid

short circuits before switching on.

6. Please ensure that the cable is secured tightly in the connector.

7. For update information please consult your supplier.

5. Safety warnings

Set DMX Address:

Set DMX decoders address as follows for multi-zone RF remote or Easylighting APP:

DMX decoders with address 001 will be controlled by zone 1,

DMX decoders with address 005 will be controlled by zone 2,

DMX decoders with address 009 will be controlled by zone 3,

DMX decoders with address 013 will be controlled by zone 4,

DMX decoders with address 017 will be controlled by zone 5,

DMX decoders with address 021 will be controlled by zone 6,

DMX decoders with address 025 will be controlled by zone 7,

DMX decoders with address 029 will be controlled by zone 8,

Each zone can pair endless of DMX decoders if you set the address accordingly.

Easylighting application manual:

Conﬁgure

There are two different ways to conﬁgure smart phone or tablet connect to the interface:

1. Connect WiFi LED controller to your home network

2. Use direkt EasyLighting connection with the WiFi LED controller

Connect WiFi LED controller to your home network

Most popular way when need to control LED lighting by own house‘s WiFi.

1) Using the WiFi connection on the smartphone or tablet, locate the LED RF & DMX WiFi Interface

Ethernet Controller and connect it - enter the password on the device below (factory setting pass-

word: 0123456789)

2) Open the Easylighting APP

3) Short press the „Setting“ Button (P1)

4) Choose the button „Connect WiFi LED controller in your home network“

5) Press „Yes“, it will search all the router around automatically. (P2, P3)

6) Choose your home network (P3)

7) enter your router password and press the „OK“ button (P4)

8) The interface is now connected with your home network via your router.

Use direct EasyLighting connection with the WiFi LED controller

1) Using the WiFi connection on the smartphone or tablet, locate the LED RF & DMX WiFi Interface

Ethernet Controller and connect it - enter the password on the device below (factory setting pass-

word: 0123456789)

2) Open the Easylighting APP

3) Short press the „Setting“ Button (P1)

4) Choose the button „Use direct Easy Lighting connection with the WiFi LED controller“

5) Press „Yes“ to conﬁrm the connection

6) The interface is now connected with your smartphone or tablet.

Restore WiFi settings to factory default setting

When we control WiFi by exist network, the mold of WiFi controller was changed. Easilighting can-

not be search in the network list unless we reset the router. Then we can use this button to restore

the WiFi controller to factory setting. (This function only is use when using exist WiFi network).

1) Connect exist WiFi and make sure WiFi controller already be conﬁgure to this network

2) Open the Easylighting APP

3) Short press the „Setting“ Button

4) Choose the connection „Restore WiFi setting to factory default settings“

5) Press „Yes“ it will indicate successful restore factory setting (P6)

6) Press „OK“, after around 1 minute you will ﬁnd the controller in your network list again on your

smartphone or tablet.

a) Edit room / zone name

1) Press in the Menu Room editing information the point „Edit“ on the above left side (P9)

2) Choose the required zone/room (for example Bedroom)

3) Clear the old name and enter a new name (for exampel zone

4) Press short „Save“ Button (P11)

b) Change the picture for the room

1) Press in the Menu Room editing information the point „Edit“ on the above left side (P9)

2) Choose the required zone/room (for example Bedroom)

3) Camera function from smartphone or tablet will opened automatically

4) Take a picture

5) Press short „Use Photo“

6) Press „Save“ Button to conﬁrm the settings

c) Edit the color wheel for corresponding LED lighting

1) Press in the Menu Room editing information the point „Edit“ on the above left side (P9)

2) In the room menu there are four different color wheels for Mono, Dynamic White, RGB and

RGBW.

3) Cancel the mark for other three color wheels and keep one which you connected the LED (take

single color as example) (P10)

4) Press the „Save“ Button to conﬁrm the setting

Different zones which were edited to different color wheel cannot be choose at same time. different

Zones which were edited to same color wheel or did not be edited any color wheel can be selectted

at same time.

Room editing information

1) Open the Easylighting APP

2) Short press the „Setting“ Button

3) Short press „Edit room information“ there will be room editing page as (P9).

Long press on the middle of the room picture to turn on/off the corresponding rooms/zones.

There will be a red off mark on the right upper side of the room picture when the room is

switched off.

Color wheel

There will be four different color wheels we can select if we did not edit in the zone/room:

Mono, DW, RGB and RGBW

1. Slide the upper areas from top to down to choose the color wheel from on to one.

Press twice to get to the color wheel selection menu, where you can also select the desired color

wheel.

Zone / Room Button

1. Press the Zone / Room Button

2. Press short in the middle of the zone / room picture

3. on the right upper side there will be a mark to conﬁrm the selection. multiple rooms can be

choose at same time

4. Press the Zone / Room Button again to conﬁrm the „Room‘s“ selection.

5. Upper area will indicate rooms name we selected

Pause & Play Button

The Play Button only exists in RGB or RGBW color wheel interface. Press the Pause & Play button,

a color begins to start, press again, it stops. Press the Pause & Play button again to start the next

saved color gradient. There are a total of 10 pre-programmed color gradients stored. If you select a

color while the gradient has stopped, the gradient program will start all over again.

fastest speed

moving speed adjustible

lowest speed

Music

LED lighting will move according the

voice decibel nearby. Bigger decibel,

faster speed. LED lighting will back to

adjusted speed when no voice effected

LED lighting will move accor-

ding the level of music voice.

Bigger decibel , faster speed.

LED lighting will back to ad-

justed speed when no voice

effect. When choose the mu-

sic button, it will open your

local music player.

language sensitivity

Lowest setting needs loud

sounds to change the speed

Highest setting requires

quiet sounds to change the

speedfront.

RGB / RGBW brightness level line

This button exists only in RGB/RGBW color wheel.

1. Short press the button

2. Brightness level can be adjusted from 0 - 255 to an accurae color.

White Button

This button only exists in RGBW channels color wheel interface to adjust white channel brightness

independently.

100% brightness

white channels

brightness level

1% brightness

Long press of the White (W) Button to switch the white channel ON/OFF independently.

Before adjust the color by color line, LED might in

already in an existing color, so we need zero clearing

each channel ﬁrst: moving each channel in any level

between 1-225, then move it back to zero, then RGB

lightig will off which means zero clearing successfully.

Table of contents

Popular Wireless Router manuals by other brands

Milesight

Milesight UG67 user guide

Airlogic

Airlogic AirSync Class 1 Features

Samsung

Samsung WCH730B user manual

TELEFONICA

TELEFONICA USB Adapter quick start guide

NETGEAR

NETGEAR PowerLINE WiFi 1000 Series quick start

Askey

Askey RAC2V1K user manual

Alloy

Alloy WLF2454AP-S user guide

TP-Link

TP-Link TL-WR542G user guide

NETGEAR

NETGEAR WNR2000v4 user manual

Hama

Hama 53120 Operating instruction

Intellinet

Intellinet 524582 user manual

Asus

Asus RT-N10P user guide

D-Link

D-Link DIR-506L Quick installation guide

Sapido

Sapido GR297n user manual

Asus

Asus DSL-N55U user guide

AMTC

AMTC WR7502 user guide

Compaq

Compaq CP-2W - iPAQ Connection Point manual

SMC Networks

SMC Networks WBR14-N2 FICHE user guide