AURES LCDWIDE 22' FP Series User manual
LCDWIDE 22’ FP Series
Touch Screen LCD Monitors
USER’s GUIDE
Rev.B
The information contained in this document is subject to change without notice.
This document contains proprietary information that is protected by copyright.All rights
are reserved. No part of this document may be reproduced,translated to another language
or stored in a retrieval system, or transmitted by any means, electronic, mechanical,
photocopying, recording, or otherwise, without prior written permission. Windows is a registered
trademark of Microsoft, Inc. Other brand or product names are trademarks of their respective
holders.
The test results show that this device meets the FCC rules. Those limits are set to protect
residential areas from the devices with harmful emission. This device will produce, use and
radiate radio frequency energy. In addition, failure to follow the user’s manual to install or use
this device might produce harmful interference with radio communication. Not withstanding
the foregoing, it does not guarantee that this type of harmful interference does not occur in
some special installations. The interference caused by this device to the reception of radio
or television signals may be veried by turning it on and off. Any changes or modications to
this TFT LCD would void the user’s authority to operate this device.
Table of Contents
Usage Notice
Precautions............................................................................................................................. 1
Introduction
About LCDWIDE 22’ FP Series............................................................................................. 2
Touch Screen for LCDWIDE 22’ FP ...................................................................................... 2
Package Overview ................................................................................................................. 3
Installation
Product Overview................................................................................................................... 4
Front View ......................................................................................................................... 4
Bottom View ..................................................................................................................... 4
Attaching the L-Brackets ........................................................................................................ 5
Side Mount for Your Monitor................................................................................................... 6
VESA Mount for Your Monitor................................................................................................. 8
Sealing foam installation......................................................................................................... 9
Connecting the Display (Figure 10.1)................................................................................... 10
(Figure 10.1)......................................................................................................................11
User Controls
Back Panel Controls............................................................................................................. 12
How to Use the OSD Menus ................................................................................................ 13
On-Screen Display Menus.................................................................................................... 14
Appendix
Troubleshooting.................................................................................................................... 15
Warning Signal ..................................................................................................................... 16
No Signal......................................................................................................................... 16
Going to Sleep................................................................................................................. 16
Out of Range................................................................................................................... 16
Product Dimensions ............................................................................................................. 17
Compatibility Modes............................................................................................................. 18
Touch Screen Driver Installation........................................................................................... 19
LCDWIDE 22’ FP Driver Install Instructions................................................................... 19
Usage Notice
! Warning - To prevent the risk of re or shock hazards, do not expose
this product to rain or moisture.
! Warning - Please do not open or disassemble the product as this may
cause electric shock.
Precautions
Follow all warnings, precautions and maintenance as recommended in this user’s manual to
maximize the life of your unit.
Do:
• Turn off the product before cleaning.
• Touch screen surface may be cleaned using a soft clean cloth moistened with mild
window glass commercial cleaners or 50/50 mixture of water and isopropylalcohol.
• Use a soft cloth moistened with mild detergent to clean the display housing.
• Use only high quality and safety approved AC/DC adapter.
• Disconnect the power plug from AC outlet if the product is not going to be used for an
extended period of time.
Don’t:
• Do not touch the LCD Display screen surface with sharp or hard objects.
• Do not use abrasive cleaners, waxes or solvents for your cleaning.
• Do not operate the product under the following conditions:
- Extremely hot, cold or humid environment.
- Areas susceptible to excessive dust and dirt.
- Near any appliance generating a strong magnetic eld.
- In direct sunlight.
1
Introduction
About LCDWIDE 22’ FP Series
The LCDWIDE 22’ FP Series is a 21.5" at panel screen with an active matrix, thin-lm
transistor (TFT) liquid crystal display (LCD).
This unit is to be used as commercial and light industrial equipment only.
Features include:
• Direct Analog signal input
• Direct Digital signal input
• Active matrix TFT LCD technology
• 1920 x 1080 resolution
• 21.5" viewable display area - 16:9 aspect ratio
• 31.47 ~ 82.3 KHz horizontal scan
• 56 ~ 75 Hz high refresh rate
• 0.24795mm x 0.24795mm pixel pitch
• Auto adjustment function
• Multilingual OSD user control
• 100 mm VESA mount
• Touch screen with USB controller
Touch Screen for LCDWIDE 22’ FP
• Projected Capacitive touch screen for nger input only
• Surface: Glare treatment
• Interface: USB controller
• Transmittance: 90±5%
• HID: Windows® 7/8
• Driver: Windows®, VISTA, XP, 2000, CE, XP Embedded,
Linux kernel 2.6.X(32 bit & 64 bit), Apple®Mac OS.
2
3
Package Overview
LCD Display Power Cord VGA Signal Cable
DVI-D CableUSB Cable ( A to B ) DC Power Supply
Touch Driver CD
Remote Key
(sold separately)
Side Brackets
Bracket Screws
4
Product Overview
• Front View
• Bottom View
VGA USB
DC IN
DVI
RJ Type
Attaching the Side Brackets
Depending on your mounting scheme, alternately, you may use the side brackets to mount
your displays onto your wall or device.
Find a suitable location for attaching side brackets.
A. The left and right sides
B. The Top and bottom sides
Note:
You will need a screwdriver to attach the side brackets.
Your kiosk touch monitor included four side brackets (and eight screws, M4x8).
This equipment is intended to be mounted in accordance with the proper hardware and the
installation instructions supplied with the product. Use of mounting brackets or screws other
than those specied in the installation instructions may cause a hazard.
5
OR
Bracket
Bracket
Bracket
Bracket
Side Mount For Your Monitor
This monitor can be mounted to the wooden or concrete wall with 8 screws and two pairs of
brackets on the opposites.
6
OR
186.0
20.0
1.0
37.4
1.0
220.0
4.1
51.6
Customer panel material:
1. Wooden wall: Ø4.5mm thru holes for M4 screws w/nuts, or no thru holes, screws for wood
4mm.
2. Sheet metal: concealed head threaded studs M4 w/nuts.
IMPORTANT!
The wall mounting instructions are for the qualied wall mounting person only!
! Warning!
Please select the proper screws!
The distance between the back cover surface and the bottom of the screw hole
is 8 mm. Please use four M4 screws diameter with proper length to mount your
monitor.
Please note: the mounting stand must be able to support at least 13.2 lbs (6Kg).
7
(158.7 mm)
317.3 mm +1.0
0.0
(260.7 mm)
521.4 mm +1.0
0.0
4-R7.4
RECOMMENDED CUSTOMER PANEL CUT-OUT
(65.0 mm)
130.0 mm
170.0 mm
(65.0 mm)
130.0 mm
170.0 mm
(158.2 mm)
316.3 mm+1.0
0.0
(260.2 mm)
520.4 mm+1.0
0.0
4-R6.9
546.6 mm
342.5 mm
RECOMMENDED CUSTOMER PANEL CUT-OUT
(Front Mount Recommend gap size 2.0mm)
(Rear Mount Recommend gap size 1.5mm)
Table of contents
Other AURES Monitor manuals
