Audiovox LCM5043NP Installation instructions
LCM5043NP & LCM5643NP
Remote Controlled Color Display Monitor
with Headphone Jack
Installation and Owner's Manual
ELECTRONICS COR
P.
®
1
EXPLANATION OF GRAPHIC SYMBOLS
WARNING:
TOPREVENTFIRE ORELECTRICSHOCK HAZARD,DONOTEXPOSE
THISPRODUCT TORAIN ORMOISTURE.
CAUTION:
1. This product is designed to operate with a 12 volt, negative ground bat-
tery system.
2. Disconnect the ground wire from the battery terminal before connecting
the electrical system. Refer to the electrical connection diagram to avoid
wrong connection of the electrical system.
Always use authorized service center for service assistance.
3. Do not operate the monitor at temperatures below 32°F (0°C) or above
104°F (40°C).
4. Keep the monitor clean and dry.
5. Never attempt your own repairs. This unit should be installed and re-
paired by qualified technicians or service personnel..
6. Do not drop the monitor or expose to strong impacts.
7. Do not expose to direct sunlight for extended periods of time.
8. Use proper insulation material to prevent short-circuiting of the supply
system.
9. Tighten all loose wires after installation.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO
NOT REMOVE COVER (OR BACK) NO SERVICEABLE PARTS
INSIDE REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with the arrowhead within a triangle is in-
tended to alert tell the user that parts inside the product are
capable of producing an electric shock .
The exclamation point within a triangle is intended to alert the
user that important operating and servicing instructions are
being provided.
2
SYSTEM OVERVIEW
TheLCM5043NPiscomprisedofa 5"ThinFilmTransistor(TFT)Liq-
uidCrystalDisplay(LCD)Monitor. TheLCM5643NPiscomprisedofa
5.6"ThinFilm Transistor(TFT)LiquidCrystalDisplay ( LCD)Monitor.
TheMonitorforbothofthesesystemshavea4:3AspectRatiodisplay
that allows the user to select between two video sources (Not Sup-
plied). TheMonitorsdisplays allfunctionswiththecomprehensive On
Screen Display (OSD). Can be used with an optional Wired Head-
phone.
OPTIONAL AUDIO CONNECTION
1) WiredHeadphones......................................... P/N=HP275
Wired Headphones
MATERIALS LIST
1. System Monitor (LCM5043NP=136C2187) or (LCM5643NP=136C2186) (1pc.)
2. Remote Control Unit (136B2156) with Lithium Battery, 3V,CR 2025 (1pc.)
3. Interconnect Box (136B2183) (1pc.)
4. Monitor Cable, 8' (112B3152) (1pc.)
5. Headrest Mounting Tray (LCM5043NP=102C3740)
or(LCM5643NP=102C3742) (1pc.)
6. Trim Ring for Mounting Tray (LCM5043NP=102B3741)
or(LCM5643NP=102B3743) (1pc.)
7. Power Cable, 2.46' (112B3127) (1pc.)
8. Removal Tool (108B3632) (1pc.)
!
"
#$
%&'
4
VEHICLE PREPARATION
1) Decide on the system configuration and the options that will be in-
stalled (i.e.whatcomponents, VCP,DVD, TV Tuner,VideoGame,
Monitor,FMModulator,etc.).
2) Read the manuals and get familiar with the electrical requirements
andconnections.
3) Decideonthemountinglocationsandmethodsofmountingtheprod-
ucts.
4) Preparethevehicle by removing anyinteriortrimnecessary to gain
accesstothevehicle'swiringaswellasallareaswhereinterconnect-
ingwireharnesseswillbelocated.Ifanyaccessholesneedtobecut
intothevehicle,headrests,orothertrimcomponents,thisshouldbe
performednow.(RefertotheInstallationProcedure).
5) Runthewiringharnessesandcablingthroughoutthevehicleasnec-
essary.(Refertothewiringinstructionsfortheindividualcomponents
andaccessoryoptionsbeinginstalled).Besure,thatallthewiringis
protectedfromsharpedgesandisroutedinsuchamannerthatitwill
not be pinched, when it is fully installed. Be sure to leave enough
slack in the wiring at each component to allow sufficient working
room.
6) Remove all the A/V system components from their packaging and
thenplacetheminthevehicleattheirrespectivelocations.
7) Locateanaccessorypowersource(RedWire)(+12VDCpresentwhen
theignition keyis in the accessory and run positions. 0VDC should
bepresent,whentheignitionkeyis in the OFF position). Generally,
thesewirescanbefoundattheignitionswitchor fuse box.
8) LocateaConstantPowerSource(YellowWire)(+12VDCpresentat
all times).
NOTE: Ensure that the accessory power is fused at the source.
Failure to do so may result in vehicle wiring damage.) Ground the
blackwire toa chassis ground close to the mounting location of AV
sources.
9) Connectallthecomponentstogether(electrically)andverifythatthe
proper operation of all the system functions. NOTE: This is best
doneBEFOREthecomponentsarepermanentlymounted.
4
5
10) Afterverifyingtheproperoperationofthesystem,proceedtomount
eachcomponent.
11) The mounting method, and the location will vary from vehicle to
vehicle, so this manual will only focus for the installation of the
12) The best location for the system components is:
a)Monitor:Headrestorbracket(optional)mountedontoaflat
surface.
b) System Interconnection Box (AVX-6869): In line with all
the system cabling and in an area were it can be easily ac-
cessed.
c)SystemMain Cable: Undereitherseat where monitors
arelocated.
Tools and Materials Required:
Utility knife or box cutter with sharp blade.
PermanentMarker.
TieWraps.
INSTALLATION
OptionalBracket Mounting:
This procedure describes mounting the system monitor using an op-
tionalSurface MountBracket (sold separately,#FB1)
1) Start by firmly attaching the Surface Mount Bracket onto a flat
surface
IMPORTANTNOTICE
It is unlawful in most jurisdictions to drive a motor vehicle which is
equipped with a television viewer or screen that is located at the point
forward of the back of the driver’s seat, or that is visible directly or indi-
rectly, to the driver while operating the vehicle.
6
3) Adjust viewing angle of monitor by tightening the fastener at the
side.
4) When the system components are mounted, test the system to
verifythatit isfunctioningcorrectly. Makesurethatnowiringwas
pinched,orconnectedimproperly duringthefinalinstallation.
Surface Mount
MountingBracket
FastenerWheel
Monitor
2) Slide monitor onto Surface Mount Bracket and then tighten the
fasten wheel.
SurfaceMountFastener
7
1) Removetheheadrestfromthe
vehicleforeasiestinstallation.
2) Layheadrestonaflatsurface.
3) Center trim collar on headrest
asshown.
NOTE: Depending on the angle of
the headrest the Trim Ring and
housing may be mounted upside
down.
4) Using a Permanent Marker,
mark headrest material along
theinteriorofthe TrimRing.
5) Remove the Trim Ring and
markan“X”fromcornertocor-
nerasshown.
Headrest Mounting:
Monitor Mounting
Tray Trim
Ring Headrest
9) Usingyourfingers,tearthefoam
out of the headrest leaving a re-
cess where the shell will be in-
serted.
NOTE: At this point you will need to
installtheharnessupthroughthearea
into the recess. It may be helpful to
followoneofthepostsandtiewrapit
to the post for restraint.
6) Using the utility knife, cut the
headrest material along the “X”
lines. Do not cut the material
alongthe other lines at this time.
7) Thiswillleaveyouwithan“X”cut
asshown.
8) Pulltheflapsupandcutthefoam
beneaththematerialtotheproper
depth. Cut all four sides of the
foam.
8
11) Guidethecablethroughtheside
openingoftheMountingTrayand
plug it into the Monitor. Make
sure the connector locks into
place. InserttheMonitorintothe
Mounting Tray and secure the
cable using tie wraps or screws
12) Turn the Monitor around and in-
sert it into the Mounting Tray
housing. Snap into place.
10) Lay the flaps of headrest mate-
rialdownintotherecess and in-
sert the Mounting Tray into the
recess. Check for fit. If it does
notfitproperly,you mayneedto
removesomemorefoam.
NOTE:TheMountingTraywill need
tobesecuredtothe headrest,either
by using tie straps, screws, ect..
13) ConnecttheMonitorpowerinput
plugtoaDCpowersource(Red
plug+12 VDC, Yellowplug +12
VDCConstantandBlackplug(-)
toground).
14) Connect the external video
sourceoutputsignal(fromVCP/
DVD, TV Etc.) to the VIDEO IN
jack. Test the system to verify
properinstallation.
9
This manual suits for next models
1
Table of contents
Other Audiovox Monitor manuals
Audiovox
Audiovox ACAM250 Instruction Manual
Audiovox
Audiovox MMD154 User manual
Audiovox
Audiovox LCM58N User manual
Audiovox
Audiovox ACAM350 Instruction Manual
Audiovox
Audiovox LCM-4000 User manual
Audiovox
Audiovox LCM50 User manual
Audiovox
Audiovox AOM562A Instruction Manual
Audiovox
Audiovox ACAM350 Installation guide
Audiovox
Audiovox LCM-0565 User manual
Audiovox
Audiovox LCM-0565 User manual
Audiovox
Audiovox LCM-5600 User manual
Audiovox
Audiovox AVXMTG10U User manual
Audiovox
Audiovox MZ7TFT User manual
Audiovox
Audiovox Movies2Go AVXMTGHR1D User manual
Audiovox
Audiovox LCM45NB - LCM 45NB - LCD Monitor User manual
Audiovox
Audiovox LCM45NB User manual
Audiovox
Audiovox D1909 - DVD Player - 9 User manual
Audiovox
Audiovox LCM-5600NP User manual
Audiovox
Audiovox VBPEX5 User manual
Audiovox
Audiovox EX50 User manual
