Audio Technica BP3600 User manual
BP3600
Immersive Audio Microphone
User Manual
English
1
Safety precautions
Although this product was designed to be used safely, failing to use it correctly may result in an accident. To ensure
safety, observe all warnings and cautions while using the product.
Cautions for the product
Do not subject the product to strong impact to avoid malfunction.
Do not disassemble, modify or attempt to repair the product.
Do not handle the product with wet hands to avoid electric shock or injury.
Do not store the product under direct sunlight, near heating devices or in a hot, humid or dusty place.
Do not place the product on an unstable surface to avoid injury or malfunction due to falling or the like.
2
Notes on use
Be sure to read the connected device’s user manual before use.
When the product is used for a long time, the product may become discolored due to ultraviolet light (especially
direct sunlight) and wear.
Make sure to hold the plug when connecting and disconnecting the cable. The cable may become severed or an
accident may occur if you pull on the cable itself.
When using the cable, be careful not to twist it to prevent damage to the cable.
Do not wind the cable at the base of the plug. Doing so may result in disconnection.
When plugging the cable into the microphone and the connected device, check that the connector is facing in the
correct direction before inserting it straight. Inserting the connector or plug diagonally may cause a malfunction.
For important recordings, perform a trial recording beforehand to make sure that the sound is recorded correctly.
Audio-Technica will not be liable in any way for any loss or damage to software or data connected to the product.
Do not apply excessive force to the connector by rotating the microphone module.
When installing the product in a suspended position, be sure to attach a wire to prevent the product from falling.
When installing the product in a suspended position, Audio-Technica will not be liable in any way for accidents such
as falling due to inadequate strength of the installation or equipment.
3
Package contents
1
5
2
6
3 4
1
Microphone module × 8
2
Core body
The AT8476 stand clamp for 5/8”-27 threaded stands and the 5/8”-27 to 3/8”-16 threaded adapter are attached to
the core body in advance. The stand clamp cannot be removed.
3
Case
4
5 m (16') microphone cable (BP3600/CABLE)
5
Windscreen × 8 (AT8172)
6
Caution Guide
4
Accessories (sold separately)
1 2 3
1
20 m (66') microphone cable (BP3600/CABLE20EXT)
Use this accessory to extend the microphone cable.
2
Windshield (× 1) (BP3600/WS)
Use this accessory to reduce wind and other noises when outside, etc.
3
Windjammer (× 1) (BP3600/WJ)
Use this accessory with the windshield to further reduce wind and other noises.
5
Storage in the case
The case contains the microphone modules, core body, and windscreens. Make sure to check the storage direction
indicators on the bottom of the case before storing parts.
2
3
1
1
Windscreen × 8
2
Core body
3
Microphone module × 8
6
Part names and functions
Microphone (BP3600/MIC)
1
8
9
2
3
4
6
5
7
1
Windscreen (AT8172)
2
Microphone module
3
Connector lock
4
Core body
5
Channel ID color ring
6
Grip
7
Output connector
8
Strap for seismic cable
9
AT8476 stand clamp for 5/8”-27 threaded stands
The 5/8”-27 to 3/8”-16 threaded adapter is attached in advance.
7
Using the product
Assembling the microphone
1Attach the windscreen to the microphone module.
Push the windscreen all the way on.
2Attach the microphone module to the core body.
Check the connector orientation before attaching the microphone module.
3Rotate the connector lock clockwise to secure the microphone module to the core body.
If the marking on the microphone module is aligned with the marking on the core body, the lock is
disengaged. Rotate the connector lock to misalign the marking and engage the lock to secure the microphone
module to the core body.
Using the product
8
4Repeat steps 1 to 3 to attach all eight microphone modules to the core body.
5Connect the microphone cable to the core body output connector.
6Connect the microphone cable to a device (mixer or recorder) that has a microphone input (balanced
input) compatible with a phantom power supply.
Before recording, make sure an audio signal is being output from all eight channels.
Using the product
9
1
2
1
Mixer
2
Recorder
Extending the cable
When using the 20 m (66') microphone cable (BP3600/CABLE20EXT) (sold separately) to extend the cable, connect
them as shown in the figure.
1 2
1
20 m (66') microphone cable (BP3600/CABLE20EXT) (sold separately)
2
5 m (16') microphone cable (BP3600/CABLE)
Table of contents
Other Audio Technica Microphone manuals
Audio Technica
Audio Technica U857R Owner's manual
Audio Technica
Audio Technica ATR1300 User manual
Audio Technica
Audio Technica PRO 47T User manual
Audio Technica
Audio Technica ES915SC Owner's manual
Audio Technica
Audio Technica ATR2500x-USB User manual
Audio Technica
Audio Technica AT2020USB-XP User manual
Audio Technica
Audio Technica AT4047 User manual
Audio Technica
Audio Technica unipoint U841R User manual
Audio Technica
Audio Technica ATM710 User manual
Audio Technica
Audio Technica MicroSet BP892 User manual
Audio Technica
Audio Technica UniPoint AT899 User manual
Audio Technica
Audio Technica ES947 Owner's manual
Audio Technica
Audio Technica UniPoint AT857QMa User manual
Audio Technica
Audio Technica M2 Manual instruction
Audio Technica
Audio Technica UniPoint AT853RWx User manual
Audio Technica
Audio Technica ES915SC Owner's manual
Audio Technica
Audio Technica ATR2100x-USB User manual
Audio Technica
Audio Technica AT4033a User manual
Audio Technica
Audio Technica AT2020USB+ User manual
Audio Technica
Audio Technica PRO 25ax User manual
