Atlas Copco SmartHEAD User manual

smartHEAD Installation Guide

1 (4) 9836 4569 01 Revision 4

smartHEAD INSTALLATION GUIDE

Index:

INSTALLING THE smartHEAD on the STwrench.................................................................................2

INSTALLING THE smartHEAD on the MRTT-C...................................................................................3

GENERAL

The smartHEAD, to be installed on the STwrench and MRTT-C,

defines the wrench capacity. You can install or change the smartHEAD

without the need of any further settings or calibration: the STwrench

and STanalyser loads automatically the transducer data at the power

on.

PACKAGE

Refer to the check list included for the package list.

SAFETY

Warning: Read the STwrench Product Instruction (No. 9836 4489 00) and MRTT-C User Guide (No.

9836 5984 01) before installing and using the product.

HANDLING

The module is electrostatic sensitive device; DO NOT touch any electrical contact to avoid risk of

module damages.

If possible, before handling any STwrench modules, touch with your hand a big metallic object,

in order to avoid electrostatic discharges while handling the modules.

Observe the following precautions to handle the module:

Correct handling: NOT correct handling:

smartHEAD Installation Guide

2 (4) 9836 4569 01 Revision 4

INSTALLING THE smartHEAD on the STwrench

1. SWITCH OFF THE STwrench.

2. INSERT THE smartHEAD IN THE WRENCH CONTROLLER AND TIGHTEN THE LOCKING NUT UNTIL

WHEN THE “CLICK” IS HEARD

NOTE: there is only one way to insert the smartHEAD into the wrench controller. The guide and

the reference pin must be inserted in the relative housings; do not force them in other position.

3. TURN ON THE STwrench

4. IF THE FOLLOWING MESSAGE IS SHOWN, CHECK THE DATE AND SELECT YES TO CONTINUE

AND USE THE smartHEAD (the first use date is set at the date shown):

Guide

Reference PIN

Locking nut

smartHEAD

smartHEAD Capacity Indication

STwrench

smartHEAD Installation Guide

3 (4) 9836 4569 01 Revision 4

Selecting No the first date is not set, but the smartHEAD is blocked. The messsage above is

shown again at the next STwrench power on.

5. IF THE smartHEAD IS NOT PROPERLY INSTALLED THE FOLLOWING MESSAGE IS SHOWN:

NOTE: each smartHEAD is intended to be associated to a single STwrench controller!

The smartHEAD interchangeability assures easy and fast maintenance operations and wrench

upgrade. IMPORTANT NOTE:

Assembling different heads on the same controller during the normal wrench operations is an

improper use of the modularity concept, and will invalidate the warranty on the wrench

components.

The smartHEAD should be left always connected to the controller. For example, do not

disassemble it at the end of the day of for wrench transportation.

INSTALLING THE smartHEAD on the MRTT-C

6. DISCONNECT THE MRTT-C FROM THE STanalyser / STa 6000.

Locking nut

smartHEA

MRTT

Date

smartHEAD Installation Guide

4 (4) 9836 4569 01 Revision 4

7. INSERT THE smartHEAD IN THE MRTT-C AND TIGHTEN THE LOCKING NUT UNTIL WHEN THE

“CLICK” IS HEARD

NOTE: there is only one way to insert the smartHEAD into the MRTT-C. The guide and the

reference pin must be inserted in the relative housings; do not force them in other position.

8. CONNECT THE MRTT-C TO THE STanalyser / STa 6000 AND TURN ON THE STanalyser / STa 6000

9. IF THE FOLLOWING MESSAGE IS SHOWN ON STa 6000, CHECK THE DATE AND SELECT YES TO

CONTINUE AND USE THE smartHEAD (the first use date is set at the STa 6000 date):

Selecting No the first date is not set, but the smartHEAD is blocked. The messsage above is

shown again at the next STa 6000 power on.

10. IF THE smartHEAD IS NOT PROPERLY INSTALLED THE Transducer Error MESSAGE IS SHOWN.

NOTE: each smartHEAD is intended to be associated to a single MRTT-C!

The smartHEAD interchangeability assures easy and fast maintenance operations and system

upgrade. IMPORTANT NOTE:

Assembling different heads on the same MRTT-C during the normal operations is an improper

use of the modularity concept, and will invalidate the warranty on the wrench components.

The smartHEAD should be left always connected to the MRTT-C. For example, do not

disassemble it at the end of the day of for transportation.

Guide

Reference PIN

Date / time

Table of contents

Other Atlas Copco Power Tools manuals

Atlas Copco

Atlas Copco ETC ST81-50-15-LO5 User manual

Atlas Copco

Atlas Copco LTP61 H700-25 Instruction sheet

Atlas Copco

Atlas Copco QST42-50CT-T50-L334-H13 Instruction sheet

Atlas Copco

Atlas Copco QST50-90CT-T50-L137-H13 Instruction sheet

Atlas Copco

Atlas Copco EP7PTI55 HR10-MT Original instructions

Atlas Copco

Atlas Copco EP8PTX70 HR10-RE Instruction sheet

Atlas Copco

Atlas Copco PRO W2630 User manual

Atlas Copco

Atlas Copco ETD DS7 User manual

Atlas Copco

Atlas Copco EBL12 Instruction sheet

Atlas Copco

Atlas Copco LG 504 Maintenance and service guide

Atlas Copco

Atlas Copco Cobra mk1 User manual

Atlas Copco

Atlas Copco AME 600 Maintenance and service guide

Atlas Copco

Atlas Copco ETD M 25 AVB Instruction sheet

Atlas Copco

Atlas Copco LMS08 SR42 Instruction sheet

Atlas Copco

Atlas Copco P2505 Instruction sheet

Atlas Copco

Atlas Copco MT41-250-I06 Original instructions

Atlas Copco

Atlas Copco LTV38 R Series User manual

Atlas Copco

Atlas Copco AX28E Maintenance and service guide

Atlas Copco

Atlas Copco RTX-8 User manual

Atlas Copco

Atlas Copco ETC ST81-136-17-LO5 Original instructions

Atlas Copco

Atlas Copco EP8PTI70 HR10-MT Instruction sheet

Atlas Copco

Atlas Copco ITB-A61-30-10 Original instructions

Atlas Copco

Atlas Copco P2535-H Original instructions

Atlas Copco

Atlas Copco PRO W2611 User manual

Popular Power Tools manuals by other brands

AEG

AEG OMNI-JS Original instructions

SIP

SIP 01533 manual

Ribimex

Ribimex PRS499 quick start guide

3M Fiber Optic Connector Crimp Tool instructions

Ryobi

Ryobi P524 Operator's manual

ROJEK

ROJEK FSN 300A manual

Kemper

Kemper 1740PRO manual

WABCO

WABCO OptiTire installation manual

EINHELL

EINHELL TE-MS 18/210 Li Original operating instructions

Orgapack

Orgapack OR-T 85 Operating and safety instructions

TOUGHCUT

TOUGHCUT Diamond 400 instruction manual

Yaros

Yaros PB-3603 user manual

Fein

Fein BSS 2.0 E Repair instructions

Baileigh Industrial

Baileigh Industrial SS-2725 Operator's manual

Milwaukee

Milwaukee 2674-20 Operator's manual

Fein

Fein BLs 1.6 parts list

Princess

Princess Electric Multi Sharpener user manual

FOREDOM

FOREDOM K.1050 Operation & maintenance manual

Atlas Copco smartHEAD User manual

Popular Power Tools manuals by other brands