Atlantic Timelis Manual
1
All electrical appliances produced for the Company are guaranteed for one year against faulty material or workmanship. This applies only if the appliance has
been used for purposes in accordance with the instructions provided and has not been connected to an unsuitable electricity supply, or subject to misuse, neglect,
damage or modified or repaired by any person not authorised by the Company. This guarantee is oered to you as an extra benefit and does not aect your legal
rights. The correct electricity supply voltage is shown on the rating label attached to the appliance. Reasonable care has been taken to ensure that this guide is
accurate at the time of printing. In the interest of progress the Company reserve the right to vary specifications from time to time without notice.
ELECTRIC TOWEL WARMER
WITH REMOTE PROGRAMMER
Timelis
2
16
Installation
1/ Preparing to install the heated towel rail
Location of the device
- This device was designed to be installed in residential premises. In any other case, please call your
distributor.
- Installation must comply with the standards currently enforced in the country of use.
- Locate the heater within minimum distances from obstacles.
Do not install the device :
•In a draft likely to affect its control (under
centralised mechanical ventilation, etc…).
•Under a fixed mains outlet.
•Inside zones 0 and 1 in bathrooms.
The device has to be installed so that
switches and other controls cannot be tou-
ched by a person in the bath or shower, ex-
cept in the UK where IEE Regulations
701.512.2 and 701.512.3 apply. These allow
the use of IP24 rated products and their in-
tegral controls in Zone 2 and ouside zones.
OK KO
3
17
2/ Connecting the device
- The device must be supplied with 230V, 50Hz.
- Mains connection must be ensured using the 3-wire cable factory fitte to the heater , through a
connecting box. In damp premises, such as bathrooms and kitchens, install the connecting box at least
25cm from the ground.
- If power cable is damaged or too short, to avoid any danger it must be replaced by a qualified elec-
trician using special tools.
Heated towel rail wiring diagram
Switch the power off and connect the wires as shown in the following diagram:
Live=brown
Neutral=blue
Panel
heater cable
LIVE
NEUTRAL
Electricity
grid
GB
4
18
3/ Fixing the heated towel rail to the wall
1Unfasten the carton’s
flaps and place it
against the wall with
the lower flap folded
back and resting flat on
the floor. Prick out the
four drill holes though
the packaging (without
drilling) and then re-
move the packaging.
2Carefully mark the
drilling points with a
pencil (draw a cross,
4cm wide).
3Drill the four holes. 4Position the
four hooks
and screw
them tight.
Puissance Cote A
300 W 819 mm
500 W 1209 mm
750 W 1599 mm
5
19
1Fit the base with the screw be-
hind the towel-drying radiator
in the wanted position.
2Screw the hanger onto the
frame and tighten gently.
4/ Fitting and removing the hanger
5Screw the sup-
ports onto the
tubes without
blocking them.
Check their posi-
tion by putting
them with the
towel-drying ra-
diator into the
sheaths.
Once you found
the right position,
lock the screws
for each contact.
6Fit the towel-
drying radiator
on the wall in
the sheaths.
Screw down
each of the
locking blocks.
Put the caps
on the end of
the supports.
GB
6
20
5/ Installing the control unit
To correctly control the heating, the thermostat must measure an ambient temperature that is the most re-
presentative of your house.As the temperature probe is in the transmitter's unit, you must place the unit:
- in the bathroom,
- fixed on a wall placed on a shelf or a piece of furniture, that can be accessed by someone measuring
1.50m,
- away from sources of heat (fireplace, direct sunlight) and draughts (window, door),
IMPORTANT: Do not install the thermostat on an outside wall or in an unheated room (e.g. garage, etc.).
fixed
on the wall
about 1.50 m
off the ground
placed on
a piece of furniture
20 cm min.
Location
Fixing
Raise the cover with a screwdriver.
Using the screwdriver, remove the batteries delivered with the device (if fixed to the
wall) or remove the battery protection tab (if fixed on stand).
Fixed to the wall
Fix the thermostat using screws and plugs or onto a wall box (➊, centre-
to-centre distance = 60 mm).
Put the batteries back in place, the right way round.
Fixed on a stand
Using the stand supplied, you can place
the transmitter on a piece of furniture (see Location paragraph).
7
21
Parameters
1/ Setting the thermostat
Turn the knob to Stop and press the right button down for 5 seconds until
H200 vx:xx is displayed (maintenance menu only to be used by the installer).
Press OK.
CF01 appears on the screen.
CF01 - Correction of the ambient temperature measurement
If there is a difference between the actual temperature in the room (thermometer)
and the temperature measured and displayed by the device, this menu can be used
to change the probe's measurement to compensate for this difference (from -4°C to
+4°C in 0.1°C steps).
Adjust the setting with +or -, then press OK to confirm and move onto the next
menu.
CF02 - Temperature display in AUTO mode
Adjust the setting with +or -, then press OK to confirm and move onto the next
menu.
CF03 - Not Used
Press OK to move onto the next menu.
5 sec.
Instruction permanent display
Displayed temperature
Real room
temperature
GB
8
22
CF04 - Not Used
Press OK to move onto the next menu.
CF05 - Not Used
Press OK to move onto the next menu.
CF06 - Associating the receiver(s)
To associate the receiver, hold the magnet on the receiver's de-
tection zone for about 3 seconds, until the red light flashes.
On the transmitter, in the CF06 menu, press the +key.
The transmitter sends a frame to the receiver.The X2D symbol appears briefly.
Check that the light on the receiver has stopped blinbing.
The receiver is associated with the transmitter.
Press OK to move onto the next menu.
CF07 - Radio test
The transmitter sends a frame to the receiver every 3 seconds.The X2D symbol
appears briefly.
Check that the light on the receiver blinks each time.
Light
3 seconds
Detection
zone
9
23
Battery
indicator light
Current mode
(e.g. comfort)
Backlighted screen
Current day
Heating
activated
Program
profile
Time
Temperature
(programmed
or measured)
Setting
buttons
Automatic
mode
Selection
button
Comfort
Set
the time
Programming
Economy
Absence
Stop
Information about the
ambient temperature
Using the device
You can operate your heated towel rail in several modes, whatever the type of controls you have cho-
sen (manual or programmed):
Auto mode :
your heated towel rail will automatically switch between Eco mode and comfort mode, de-
pending on the time slots programmed for each day of the week.
Comfort mode allows you to maintain the correct ambient temperature.
Boost mode : used to start the heated towel rail in override mode for a certain period of time.
Eco mode : used to lower the temperature when you are not in your bathroom and therefore save
energy.
Frost Protection mode : used to set a temperature when you are away for a long time
GB
AUTO
10
24
Use
1/ Setting the time
Turn the knob to
the days blink and press + or – to choose the day of the week
(1. Monday, 2.Tuesday, 3.Wednesday. ......7.Sunday)
Press OK to confirm.
The hour blinks and press + or - to set it and press OK to confirm
Do the same thing for the minutes.
2/ Setting the temperatures
Turn the button on :
- Frost Protection ( ) to set the temperature when you are away (from
5°C to 15°C, 7°C by default),
- Eco ( ) to set the energy-saving temperature (from 10°C to 30°C,
15°C by default),
- Comfort ( ) o set the comfort temperature (from 10°C to 30°C,
19°C by default),
Choose using +or -.
Turn the knob to exit the setting mode.
3/ Programming (PROG)
When the device is first started up, the "Comfort from 6h to 23h" program is applied to every day of the week.
To change the setting,
turn the knob to PROG.
The 1st time slot blinks.
Press Eco or comfort, depending on how you want to program your device.
To apply the same program to the next day, hold the OK button down for about 3 seconds until the next day's
program appears.
Otherwise, press OK once and program the following days as you want.
Turn the knob to exit the programming mode.
Economy
1h
Confort
1h
Move to next
program period
Validation
and move to
next day
1st
hour
Program hour Day
Program
profil
Day
Hour
Minutes
Other manuals for Timelis
1
Table of contents
