Asus WL-330GE_M User manual
ASUS WL-330gE Setup
Jason at NSS reserved MAC Addresses for Robots and ASUS Bridges:
1463EB1
oASUS Bridge
MAC: E0-CB-4E-5D-E6-EA
IP: 172.18.63.1
oRobot:
MAC:00-80-2f-11-e0-29
IP: 172.18.63.22
Name: ese-robot-1463eb1.wufi.wustl.edu
1587CFD (14BCCCF/ MAC: 00:80:2f:11:f6:c4 sent in for repairs and was
replaced with this one)
oASUS Bridge
MAC: E0-CB-4E-1B-95-1A
IP: 172.18.63.3
oRobot
MAC: 00:80:2F:12:AE:70
IP: 172.18.63.2
Name: ese-robot-14BCCCF.wufi.wustl.edu
148CCC1
oASUS Bridge
MAC: E0-CB-4E-5D-E2-50
IP: 172.18.63.5
oRobot
MAC: 00:80:2f:11:f6:b6
IP: 172.18.63.4
Name: ese-robot-.wufi.wustl.edu
15BEF64 (1463EAB/ MAC: 00:80:2f:11:e0:21 sent in for repairs and was
replaced with this one)
oASUS Bridge
MAC: E0-CB-4E-5D-E2-EB
IP: 172.18.63.7
oRobot
MAC: 00:80:2f:12:d4:03
IP: 172.18.63.6
Name: ese-robot-15BEF64.wufi.wustl.edu
14BCCC5
oASUS Bridge
MAC: E0-CB-4E-5D-E2-10
IP: 172.18.63.9
oRobot
MAC: 00:80:2f:11:f6:ba
IP: 172.18.63.8
Name: ese-robot-14BCCC5.wufi.wustl.edu
159F58E (15EA4A2 sent for repairs. When the shipped it back it had the same
sbRIO but new serial number.)
oASUS Bridge
MAC: F4-6D-04-94-EB-22
IP: 172.18.63.11
SN: 4739
oRobot
MAC: 00:80:2f:12:B8:67
IP: 172.18.63.12
Name: ese-robot-15EA4A2.wufi.wustl.edu
Configuration Instructions for WUFI
1. Reset device by holding the reset button for 10 seconds. Then turn off for 10
seconds and plug Ethernet cable into PC and turn on.
2. Browse to 192.168.1.220
a. Username: admin
b. Password: admin
3. Select wunoreg and click on Connect. You will lose the connection to the ASUS
at this point. The MAC addresses are in the QIP tables, so the IP will be
automatically assigned according to the table above.
4. To test, change the network settings –Use the IP of the robot you are going to
connect the bridge to. Make sure it is off the network.
5. Now configure the robot to use the IP from the table above. If you do not know
the IP of the robot, then you need to reset the IP. Do this by by turning ON
(Down) DipSwitch -3 and pressing the Reset switch. Then hit refresh in MAX.
Configuration Instructions for WEP Wireless Network
1. Click on the Adapter tab, select the SSID and Click Connect. Enter the WEP
password if prompted. However, this doesn’t seem to work so you have to add it
again on the Advanced Settings page.
2. Click on Advanced -> Wireless -> Interface. Click on AP Scan
3. Click Select for the correct SSID.
4. Enter either passphrase or WEP key directly and click Save to List and Apply.
This manual suits for next models
1
Other Asus Wireless Router manuals
Asus
Asus RT-AC1200HP User manual
Asus
Asus WL-107G User manual
Asus
Asus ZenWiFi AC CT8 User manual
Asus
Asus RT-AC3200 Instruction manual
Asus
Asus RT-AC68P User manual
Asus
Asus RT-AC66U B1 User manual
Asus
Asus RT-AX53U User manual
Asus
Asus DSL-N12U_D1 User manual
Asus
Asus RT-AX55 User manual
Asus
Asus RT-AC66U B1 User manual
Asus
Asus ROG Rapture GT-AC2900 User manual
Asus
Asus DSL-N55U User manual
Asus
Asus RT-N16 User manual
Asus
Asus XC5 User manual
Asus
Asus RT-AC1200G+ User manual
Asus
Asus RT-AC1200 User manual
Asus
Asus RT-AC1900 Dual Band User manual
Asus
Asus RT-N53 User manual
Asus
Asus WL-330N3G User manual
Asus
Asus ZenWiFi XD6 User manual
