Astria Tuscan42P2 User manual

P/N 127051-01 Rev. D 10/2015

REPORT NO. 10-078

PFS

USC

P127051-01

Installation and Operation Instructions

Astria®Residential and Outdoor Wood-Burning

Fireplace

Models

Tuscan42P2

Tuscan42P3

SAVE THIS BOOK

This book is valuable. In addition to instructing you on how to install and maintain your appliance, it also contains

information that will enable you to obtain replacement parts or accessory items when needed. Keep it with your other

important papers.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Installateur : Laissez cette notice avec l’appareil.

Consommateur : Conservez cette notice pour consultation ultérieure.

This wood burning ﬁreplace complies with

UL127 CAN/ULC-S610-M87 standard as a

FACTORY BUILT FIREPLACE.

Ce foyer au bois est conforme aux UL 127 CAN/ULC-

S610-M87 norme comme une USINE CONSTRUITE

CHEMINÉE.

This ﬁreplace is approved for use as a wood burning ﬁreplace or for use with a vented gas log approved to ANSI

Z21.60 or Z21.84 standards or for use with a vent-free gas log heater approved to ANSI Z21.11.2 standard.

IHP hood must be installed when using a vent-free log heater (see Accessories, page 19).

FOR CANADA: The authority having jurisdiction

(such as the municipal building department, ﬁre

department, etc.) should be contacted before

installation to determine the need to obtain a permit.

POUR LE CANADA: L’autorité compétente (comme le

service municipal du bâtiment, les pompiers, etc.) doit

être contacté avant l’installation aﬁn de déterminer la

nécessité d’obtenir un permis.

This appliance may be installed in an aftermarket permanently located, manufactured home (USA only)

or mobile home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated

on the rating plate.

This installation manual will enable you to obtain a safe, efﬁcient and dependable installation of your ﬁreplace

system. Please read and understand these instructions before beginning your installation.

Do not alter or modify the ﬁreplace or its components under any circumstances. Any modiﬁcation or alteration

of the ﬁreplace system, including but not limited to the ﬁreplace, chimney components and accessories, may

void the warranty, listings and approvals of this system and could result in an unsafe and potentially dangerous

installation.

IMPORTANT! TO ASSURE PROPER ALIGNMENT OF GLASS DOORS: INSTALL THIS FIREPLACE IN A SQUARE

AND PLUMB CONDITION, USING SHIMS AS NECESSARY AT SIDES AND/OR BOTTOM.

Astria.US.com 127051-01D

Safety.............................................................................................2

Speciﬁcations.................................................................................4

Fireplace Installation ......................................................................5

Venting Installation ........................................................................7

Optional Gas Line Installation ......................................................12

Operation and Maintenance .........................................................13

Replacement Parts.......................................................................14

Technical Service .........................................................................14

Parts ............................................................................................15

Accessories..................................................................................18

Warranty ......................................................................................23

Thank you for your purchase. We appreciate your

business!

Please carefully read and follow all instructions in this manual. Pay

special attention to all warnings and safety information.

Following these safety, care, and operation instructions will help

ensure many years of dependable and enjoyable service from your

ﬁreplace.

To help us keep you up-to-date on product information and of-

fers, please take a few moments to register your product online

at Astria.US.com

Please read and understand these instructions before installing

or operating.

SAFETY

WARNING: Improper installation, adjustment,

alteration, service or maintenance can cause injury,

property damage or loss of life. Refer to this manual

for assistance or additional information. Consult a

qualiﬁed installer or local distributor.

IMPORTANT: Check local codes before installing this

ﬁreplace.

Before beginning installation of this ﬁreplace, read these instructions

through completely.

• ThisINNOVATIVEHEARTHPRODUCTS,LLC(IHP)replaceand

its components are safe when installed according to this installa-

tionmanual.UnlessyouuseIHPcomponents,whichhavebeen

designed and tested for the ﬁreplace system, you may cause a ﬁre

hazard.

• TheIHPwarrantywillbevoidedbyandIHPdisclaimsanyrespon-

sibility for the following actions.

a. Modiﬁcation of the ﬁreplace, components, doors, air inlet

system and damper control.

b. Use of any component part not manufactured or approved by

IHPincombinationwithanIHPreplacesystem.

Proper installation is the most important step in ensuring safe and

continuousoperationofthereplace.Consultthelocalbuildingcodes

as to the particular requirements concerned with the installation of

all factory built ﬁreplaces.

NOTICE: The ﬁrebox canopy (hood) must not be modi-

ﬁed or replaced with a canopy that may be provided

with the unvented decorative room heater.

WARNING: Do not install a ﬁreplace insert in this

box unless the manufacturer's instructions with the

insert speciﬁcally state this ﬁreplace has been tested

for use with this insert.

TABLE OF CONTENTS

FOR YOUR SAFETY

•Donotstoreorusegasolineoranyotherammable

vapors or liquids in the vicinity of this or any other

appliance.

•Duetohightemperatures,theapplianceshouldbe

located out of trafﬁc and away from furniture and

draperies.

•Donotplaceclothingorotherammablematerials

on or near the appliance.

•Never leave children unattended when a re is

burning in the ﬁreplace.

WARNING: Use solid wood or processed solid

fuel ﬁre logs only. "Do not poke or stir the logs while

they are burning. Use only ﬁrelogs that have been

evaluated for the application in ﬁreplace and refer to

ﬁrelog warnings and caution markings on packaging

prior to use."

This ﬁreplace is not intended to be used as a sub-

stitute for a furnace to heat an entire home. Use for

supplemental heat only.

Overﬁring of a ﬁreplace is a condition where exces-

sive temperatures are reached, beyond the design

capabilitiesoftheappliance.Thedamagethatoccurs

fromoverﬁringisnotcoveredunderthemanufacturer’s

limited warranty.

Astria.US.com

127051-01D 3

SAFETY Continued

WARNING: CONTINUED OVERFIRING CAN PER-

MANENTLY DAMAGE YOUR FIREPLACE SYSTEM.

SOME EXAMPLES OF CONDITIONS THAT COULD

CAUSE OVERFIRING ARE:

• BURNINGQUANTITIESOFSCRAPLUMBER,PINE

BRANCHES, PAPER OR CARDBOARD BOXES

WHICHEXCEEDTHEVOLUMEOFTHENORMAL

LOGFIRE.

• BURNINGTRASH,CHEMICALSORCHEMICALLY

TREATEDCOMBUSTIBLES.

Disposal of Ashes

Ashes should be placed in a metal container with a

tight-ﬁtting lid. The closed container of ashes should

beplacedonanoncombustibleoororontheground,

well away from all combustible materials, pending

ﬁnal disposal. If the ashes are disposed of by burial

in soil or otherwise locally dispersed, they should be

retained in the closed container until all cinders have

thoroughly cooled.

WHEN USING THE DECORATIVE APPLIANCE, THE

FIREPLACE DAMPER MUST BE SET IN THE FULLY

OPEN POSITION.

Never use gasoline, gasoline-type lantern fuel, kero-

sene,charcoallighteruid,orsimilarliquidstostart

or ’freshen up’ a ﬁre in this ﬁreplace. Keep all such

liquids well away from the ﬁreplace while it is in use.

Use SOLID WOOD only for fuel. It is best to use dry

and well seasoned hardwood. Softwoods tend to burn

veryquickly.DONOTusetreatedwood,charcoal,coal,

trash,driftwoodorwoodsthathavebeendippedintar,

pitch, pine tar, creosote, etc. Wood products made

with synthetic binders, such as plywood, produce ab-

normally high temperatures and sputtering, smoking

ﬁres. When burning artiﬁcial logs, please read and

follow the instructions provided by the manufacturer.

Never burn treated construction lumber or scraps.

These woods burn excessively hot and may contain

chemicals used to treat insects and fungus. When

burned,thesechemicalscanposeasigniﬁcanthazard.

WARNING: BURNING IMPROPER FUEL (I.E.

CHARCOAL) CAN RESULT IN CARBON MONOXIDE

POISONING, WHICH MAY LEAD TO DEATH!

Carbon Monoxide Poisoning – Early signs of carbon

monoxidepoisoningresembletheuwithheadaches,

dizziness, or nausea. If you have these signs, get

fresh air at once! Have the appliance inspected by a

qualiﬁed service technician. Some people are more

affected by carbon monoxide than others. These

include pregnant women, people with heart or lung

diseaseoranemia,thoseundertheinuenceofal-

cohol, and those at high altitudes.

Ventilation Requirements - Provide adequate air for

combustion. The fresh air requirements of this ap-

pliance must be met within the space where it will

be installed.

Smoke Detectors - Since there are always several

potential sources of ﬁre in any home, we recommend

installing smoke detectors. If possible, install the

smoke detector in a hallway adjacent to the room (to

reduce the possibility of occasional false activation

fromtheheatproducedbytheappliance). Ifyourlocal

coderequiresasmokedetectorbeinstalledwithinthe

same room, you must follow the requirements of your

localcode. Checkwithyour localbuildingdepartment

for requirements in your area.

Creosote – Formation and Need for Removal

Whenwood is burnedslowly,itproducestar andother

organicvapors,whichcombinewithexpelledmoisture

to form creosote. The creosote vapors condense in

the relatively cool chimney ue of a slow-burning

ﬁre. As a result, creosote residue accumulates on

theuelining.Whenignitedthiscreosotemakesan

extremely hot ﬁre.

The chimney shall be inspected at least twice a

year during the heating season to determine when a

creosotebuilduphasoccurred.Whencreosotehasac-

cumulated (1/8" [3 mm] or more) it shall be removed

to reduce the risk of a chimney ﬁre.

Astria.US.com 127051-01D

SPECIFICATIONS

WARNING: DO NOT INSTALL IN SLEEPING

ROOM OF MOBILE HOMES

CAUTION: THE STRUCTURAL INTEGRITY OF THE MANU-

FACTURED HOME FLOOR, WALL, AND CEILING/ROOF

MUST BE MAINTAINED

0" TO

BOTTOM

(LEFT SIDE ONLY)

OUTSIDE AIR

BACK AND

SIDES

3/4" AIR

SPACE

HEARTH EXTENSION

66" X 20" MINIMUM

12"

EACH SIDE

COMBUSTIBLE

WALL BOARD

TOP SPACERS

0" TO

1" AIRSPACE

TO COMBUSTIBLE

MATERIAL

NO COMBUSTIBLE

MATERIAL ON FACE

NO COMBUSTIBLE

MATERIAL BELOW

TOP SPACERS

GAS LINE

KNOCK OUT

AIR KIT

KNOCK OUTS

GAS LINE

STARTER

SECTION

8DM

PIPE

INNER DIA.

OUTER

DIA. 15"

KNOCK OUTS

ELECTRICAL

OUTLET

LEFT SIDE

RIGHT SIDE

PERPENDICULAR

NOT LESS

THAN 12" TO

SIDEWALL

41"

48"

42"

39"

12"

48"

36"

24"

81/8"

10 5/8"

12 5/8"

10 5/8"

63/4"

14 1/4"

21/2"

29 1/2"

22 1/2"

11 3/4"

46 3/4"

11/2"

12 3/8"

5/8"

16 1/4"

81/8"

21/2"

SQUARE CHASE-TOP

TERMINATION

ROUND TOP TERMINATION

Astria.US.com

127051-01D 5

FIREPLACE INSTALLATION

SELECTING LOCATION

To determine safest and most efﬁcient location for ﬁreplace, you

must take into consideration the following guidelines:

1. Locationmustallowforproperclearances(seeFigures1and2).

2. Consideralocationwherereplacewillnotbeaffectedbydrafts,

air conditioning ducts, windows or doors.

3. A location that avoids cutting of joists or roof rafters will make

installation easier.

4. Anoutsideairkitisavailablewiththisreplace(seeOptional

Outside Air Kitonpage7).

MINIMUM CLEARANCE TO COMBUSTIBLES

Back and sides of ﬁreplace 3/4" minimum*

Floor** 0" minimum

Perpendicular wall to opening 12" minimum

Top spacers 0" minimum

Mantel clearances see Mantels, page 6

Chimneyouterpipesurface1"minimum

*Notrequiredatnailinganges

** See step 2 of Framing

WARNING: DO NOT PACK REQUIRED AIR SPACES

WITH INSULATION OR OTHER MATERIALS.

Minimum/Maximum Chimney Height

The minimum height of the chimney, measured from the base of

thereplacetotheuegasoutletofthetermination,is14.5feetfor

straightueorauewithoneelbowset.Themaximumdistance

between elbows is 6 feet. For systems with two elbow sets, the

minimumheightis22feet.Themaximumheightofanysystemis

50 feet. This measurement includes the ﬁreplace, chimney sections

andtheheightoftheterminationassemblyattheleveloftheue

gasoutlet(seeFigure18,page11).

Minimum/Maximum Chimney Height for Outdoor Installation

The minimum height of the chimney, measured from the base of the

replacetotheuegasoutletofthetermination,is8feet(minimum

of4feetofchimneypipesectionsrequiredforoutdoorinstallation).

Figure 1 - Framing Dimensions

Figure 2 - Corner Installation

FRAMING

1. Frame opening for ﬁreplace using dimensions shown in Figures

1 and 2.

Note: When the ﬁreplace is framed, the header has to be turned

ontheattomaintainproperclearance.

2. If ﬁreplace is to be installed directly on carpeting, tile or any

combustiblematerialotherthanwoodooring,replacemust

beinstalleduponametalorwoodpanelextendingfullwidthand

depth of ﬁreplace.

3. Set ﬁreplace directly in front of this opening and slide unit back

untilnailingangestouchsideframing.

4. Checklevelofreplaceandshimwithsheetmetalifnecessary.

5. Before securing ﬁreplace to prepared framing, ember protector

must be placed between hearth extension (not included) and

under bottom front edge of ﬁreplace to protect against glowing

embers falling through. If ﬁreplace is to be installed on a raised

platform,aZ-typeemberprotector(notincluded)mustbefabri-

catedtotyourrequiredplatformheight.Emberprotectorshould

extend under replace a minimum of 1 1/2". Ember protector

shouldbemadeofgalvanizedsheetmetal(28gaugeminimum)

to prevent corrosion.

6. Usingscrewsornails,securereplacetoframingthroughanges

located on sides of ﬁreplace.

28"

Maintain 3/4"

Clearance at

Sides and

Back of

Fireplace

59 3/8"

19 1/2"

83 7/8"

23 1/2"

49 3/4"

47 1/4"

2x4

Header

Turned

Flat

Astria.US.com 127051-01D

FIREPLACE INSTALLATION Continued

FIREBOX

SAFE ZONE

Top View of Fireplace

Min. 12" from

Perpendicular Side Wall

2" Max.

33°

MANTELS

Amantelmaybeinstalledifdesired(seeFigures4and5).Woodwork

such as wood trims, mantels or any other combustible material

projecting from front face, must not be placed within 12" of ﬁreplace

openingandwithin9"oftoplouveropening.Combustiblematerials

above 12" and projecting more than 1 1/2" from ﬁreplace must not

beplacedlessthan12"fromtopopeningofreplace(NFPA211,

Section-ClearancefromCombustibleMaterial).

Mantels or any other combustible material may come up to side edge

of black metal face of ﬁreplace if projection from front face falls within

limits shown in Figure 4.

Figure 4 - Mantel Clearances to Combustible Material

12 1/4" Ref.

Ref.

15" Min.

12" Min.

11/2" Max.

3" Nom.

33°

Combustible

Material

Safe

Zone for

Projection of

Combustible

Materials

Fireplace Opening

Non-Combustible

Materials Below

Top Spacer

Upper

Section of

Fireplace

DRAIN PAN (DP42)

For outdoor installations, the ﬁreplace enclosure must allow for

adequate drainage and fresh air ventilation. It is recommended that

a sealed, corrosion resistant catch pan with provision for drainage

beinstalledunderthereplacewithinthereplaceenclosure(see

Accessories,page19).

HEARTH EXTENSION

Ahearthextensionprojectingaminimumof20"infrontofanda

minimum of 12" beyond each side of ﬁreplace opening is required

toprotectcombustibleoorconstructioninfrontofreplace.Fab-

ricateahearthextensionusingamaterialwhichmeetsthefollowing

speciﬁcations: a layer of noncombustible, inorganic material having

athermalconductivityofk=.84BTUIN/FT2HR°F(orless)at1"

thick.Forexample,ifmaterialselectedhasakfactorof0.25,such

as glass ﬁber, the following formula would apply:

0.25x1.0"=0.30"thicknessrequired

0.84

Thermal conductivity "k" of materials can be obtained from manu-

facturerorsupplierofnoncombustiblematerial.Ifhearthextension

is to be covered, use noncombustible material such as tile, slate,

brick, concrete, metal, glass, marble, stone, etc. Provide a means to

preventhearthextensionfromshiftingandsealgapbetweenreplace

frameandhearthextensionwithanon-combustiblematerialsuch

assand-cementgrout(seeFigure3).

WARNING: Hearth extension is to be installed

only as shown in Figure 3.

Figure 3 - Hearth Extension

Fireplace Front

Raised Hearth

Fireplace Front

Elevated

Seal Gap

Ember Protector

Hearth

Extension

HearthExtension,NoncirculatingModels

Astria.US.com

127051-01D 7

Figure 5- Outside Air Kit

Secure to Collars with Metal Tape, Screws

or Straps (Min. of 1/4" x 20" in size)

Air Inlet

Location

Must Allow

For Bushes

or Snow

Vent Hood

Required for

Wall Installation

Air Inlet

Eyebrow

Vented Crawl Space

(Check Local Codes

Before Installing in a

Vented Crawl Space)

VENTING INSTALLATION

OPTIONAL OUTSIDE AIR KIT (MODEL AK4/AK4F)

Installation of outside air kit should be performed during rough fram-

ing of ﬁreplace due to the nature of it's location. Outside combustion

airisaccessedthroughaventedcrawlspace(AK4F)orthrougha

sidewall(AK4).SeeFigure22,page14forinstructionofoperating

air kit.

CAUTION: Combustion air inlet ducts shall not

terminate in attic space.

The maximum height for the air vent can not exceed

3feetbelowtheuegasoutletofthetermination.

CHIMNEY PIPE

WARNING: Label part number 900599-01 must

be applied by the installer to all chimney pipe

sections but is not required on sections that will

be visible after the installation is complete. Label

must wrap around the circumference of the pipe.

See accessories, page 19 for Kit F2659.

AnIHPchimneysystemconsistsof12",18",24",36"and48"

snap-lock,double-wallpipesegments,plannedformaximum

adaptability to individual site requirements. Actual lengths gained

afterttingoverlapsmustbetakenintoconsideration(linealgain)

andaregiveninlinealgainchart(seeFigure6).

Lineal gain is actual measurable length of a part after two or more

parts are connected.

Figure 6 - Lineal Gain

Hemmed

End

8" Stainless

Inner Pipe

12 3/8"

Galvanized

Outer Pipe

WARNING: The opening in collar around chimney

at top of ﬁreplace must not be obstructed. Never use

blown insulation to ﬁll chimney enclosure.

LINEALGAIN

PARTNO. DESCRIPTION GAIN

42" Fireplace 45"

SS-8DM Starter Section 19''

12-8DM

12-8HT Pipe Section 10 5/8"

18-8DM

18-8HT Pipe Section 16 5/8"

24-8DM

24-8HT Pipe Section 23 5/8"

36-8DM

36-8HT Pipe Section 34 5/8"

48-8DM

48-8HT Pipe Section 46 5/8"

RT-8DM Round Termination 6 7/8"*

RTL-8DM Round Termination 7 3/4"*

RLT-8DM Round Termination 7 1/2"*

RTT-8DM Round Termination

with Slip Section

6 7/8" to

23 1/8"*

RTTL-8DM Round Termination

with Slip Section

8 1/2" to

21 1/2"*

RLTT-8DM Round Termination

with Slip Section

7 1/2" to

21 1/4"*

ET-8DM Square Chase-Top 12"*

ETO-8DM Square Chase-Top

with Mesh 12"*

ETL-8DM Square Chase-Top

with Slip Section 7" to 15"*

ETLO-8DM

Square Chase-Top

with Mesh & Slip

Section

12" to

25 1/2"*

* The lineal gain for the terminations is

measured to the ue gas outlet height.

Astria.US.com 127051-01D

Figure 7 - Typical Offset Installation

VENTING INSTALLATION Continued

ASSEMBLY AND INSTALLATION OF DOUBLE WALL CHIMNEY

SYSTEM

Eachdoublewallchimneysectionconsistsofagalvanizedouter

pipe,astainlesssteelinneruepipeandawirespacer.Pipesections

must be assembled independently as chimney is installed. When

connectingchimneydirectlytoreplace,inneruepipesection

must be installed ﬁrst with lanced side up. Outer pipe section can

thenbeinstalledoveruepipesectionwithhemmedendup.Press

down on each pipe section until lances securely engage hem on

ﬁreplace starter. Wire will assure proper spacing between inner

and outer pipe sections.

Note:ForCanada,usechimneypartsdesignatedHT.

Opening in collar around chimney at top of

ﬁreplace must not be obstructed. Never use blown

insulation to ﬁll chimney enclosure.

Continuetoassemblechimneysectionsasoutlined,makingsure

that both inner and outer pipe sections are locked together. When

installing double wall snap-lock chimney together, it is important to

assurejointbetweenchimneysectionsislocked.Checkbypulling

chimneyupwardafterlocking.Chimneywillnotcomeapartifproperly

locked. It is not necessary to add screws to keep chimney together

(exception-seeFigure9,page9).

The height of a vertical chimney pipe supported ONLY by the

replace,mustnotexceed20feet.Chimneyheightsabove20feet

must be supported.

USING ELBOW OFFSET 30E-12DMO-8DMR

To clear overhead obstructions, you may offset your chimney system

using 30E-12DMO-8DMR30°Offset/returnelbow.

A section or sections of chimney may be used between offsets and

return elbow. Transition pipe must be used after elbow offset is

attached.

1. To achieve desired offset, you may install combinations of 12",

18",24",36"and48"lengthofdoublewallpipe(seeoffsetchart).

Note: For systems with 2 elbow sets, minimum height is 22 feet.

Maximumheightforanysystemis50feet.

2. Chimneyweightaboveoffsetrestsonreturnelbow.Strapsmust

besecurelynailedtoraftersorjoists(seeFigure8,detailsAand

B,page9).

3. Maximumlengthofpipebetweensupports(returnelbowor12S-

8DM)is6'ofanglerun.Maximumoftwo6'anglerunsections

perchimneysystem(seeFigure7).

4. All pipe connections between offset and return must be secured

withtwoscrewsonouterpipeonly(seeFigure9,page9).Do

not penetrate inner stainless.

30E-8DM

Return Elbow 30E-8DM

Return Elbow

30E-8DM

Offset Elbow 30E-8DM

Offset Elbow

30E-12DMO-8DMR

Offset Elbow

30E-12DMO-8DMR

Offset Elbow

30E-12DMO-8DMR

Offset Elbow

30E-12DMO-8DMR

Return Elbow

30E-12DMO-8DMR

Return Elbow

30E-12DMO-8DMR

Return Elbow

Starter

Section

Starter

Section

Starter

Section

6' Max.

8 DM Pipe

6' Max.

Ceiling

Support Pipe

12S-8DM

ABC

Astria.US.com

127051-01D 9

2" Min.

Straps Straps

Straps

Detail A

Return Elbow

Detail B

Angle

Firestop

See Detail A

See Detail B

Ceiling Support

Pipe 12S-8DM

VENTING INSTALLATION Continued

Figure 9 - Elbow Offset

Figure 8 - Ceiling Support Pipe 12S-8DM

OFFSETCHARTWITHTRANSITIONPIPE

OFFSET RISE OFFSET/

RETURN

ELBOW

TRANSITION

PIPE

CHIMNEYLENGTH

AB 12" 18" 36" 48"

13 3/4" 32 1/2" 1 1

19" 41" 1 1 1 1

22" 46 3/4" 1 1 1

24 1/2" 50 3/4" 1 1 2

27 1/2" 56 1 1 1 1

30 1/4" 61 1 1 2

31 62 1/2" 1 1 1

32 1/2" 65" 1 1 2 1

35 1/2" 70 1/4" 1 1 1 2

36 1/4" 71 1/2" 1 1 1 1

37 72 3/4" 1 1 1

38 1/2" 75 1/2" 1 1 3

39 1/4" 76 3/4" 1 1 1 1

41 1/2" 80 1/2" 1 1 2 1

42 1/4" 81 3/4" 1 1 1 1

44 1/2" 85 3/4" 1 1 1 1 1

45 1/4" 87" 1 1 1 1

47 1/2" 91" 1 1 2 1

48 1/4" 92 1/4" 1 1 2

49 3/4" 94 3/4" 1 1 2 1 1

52" 98 3/4" 1 1 1 4

53 1/2" 101 1/4" 1 1 1 2

54 1/4" 102 3/4" 1 1 1 1

55 3/4" 105 1/4" 1 1 3 1

56 1/2" 1061/2" 1 1 1 2

58 3/4" 110 1/2" 1 1 2 2

59 1/2"111 3/4" 1 1 1 1 1

60 1/4" 113" 1 1 2

61 3/4" 115 3/4" 1 1 1 1 2

64 3/4" 120 3/4" 1 1 2 2

65 1/2" 122 1/4" 1 1 1 2

67" 124 3/4" 1 1 2 1 2

Screws

Astria.US.com 127051-01D

VENTING INSTALLATION Continued

Pitch Slope Opening

"A"Max.

UsedFlashing

ModelNo.

Flat 0° 15" V6F-8DM

0-6/12 26.6° 16 1/8" V6F-8DM

6/12- 12/12 45.0° 20 3/8" V12F-8DM

Figure 12 - Roof Opening Measurements

FLASHING INSTALLATION (V6F-8DM OR V12F-8DM)

Determineashingtobeusedwithroofopeningchart.Slideashing

overpipeuntilbaseisatagainstroof.Replaceasmanyshinglesas

neededtocoverexposedareaandashingbase.Secureinposition

bynailingthroughshingles(seeFigure13).DONOTNAILTHROUGH

FLASHINGCONE.

Installing Flashing on a Metal Roof

Wheninstallingashingonametalroof,itisrequiredthatputtytape

beusedbetweenashingandroof.Flashingmustbesecuredtoroof

using#8x3/4"screwsandthensealedwithroofcoatingtoprevent

leakage through screw holes. A roof coating must also be applied

aroundperimeterofashingtoprovideaproperseal.

Figure 13 - Flashing Installation

Nail Only Outer

Perimeter of

Flashing

Storm Collar

Underlap Shingles

at Bottom

Flashing

Cone

Overlap

Shingles Top

and Sides Only

FIRESTOP SPACERS (3600FS-8DM-1)

Firestop spacers are required at each point where chimney penetrates

aoorspace.Theirpurposeistoestablishandmaintainrequired

clearance between chimney and combustible materials. When pipe

passes through a framed opening into a living space above, ﬁrestop

must be placed onto ceiling from below as shown in Figure 10.

Theyalsoprovidecompleteseparationfromoneoorspacetoan-

other or attic space as required by most codes. When double wall

pipe passes through a framed opening into an attic space, ﬁrestop

mustbeplacedintoanatticoorasshowninFigure11.

Figure 10 - Firestop Spacer with Living Space Above Ceiling

Figure 11 - Firestop Spacer with Attic Space Above Ceiling

IMPORTANT NOTICE

When penetrating a ceiling into an attic, a ﬁrestop thimble

(38FST or FST30) is required to avoid intrusion by insulation

and recommended to negotiate a joist (see Figure 11a).

30"

(76.2 cm)

Minimum Measurements

Opening "A"

(48.3 cm)

(2.54

cm)

(2.54

cm)

(2.54 cm)

Existing

Ceiling

Frame

Firestop

Spacer

Screws or

Staples

(Min. of 8)

Firestop

Spacer

Screws or Staples

(Min. of 8)

Existing

Ceiling

Frame

Figure 11a - Firestop Thimble

Thimble

38FST or

FST30

Firestop

PENETRATING ROOF

To maintain a 1" clearance to pipe on a roof with a pitch, a rectangular

opening must be cut.

1. Determine center point where pipe will penetrate the roof.

2. Determine center point of the roof. Pitch is the distance the roof drops

over a given span, usually 12". A 6/12 pitch means that the roof drops

6" for each 12" measure horizontally down from roof rafters.

3. Useroofopeningchart(Figure12)todeterminecorrectopening

lengthandashingrequired.

4. Removeshinglesaroundopeningmeasured.Cutoutthissection.

5. Addnextsections of pipeuntilendpenetratesroofline. Check to

seethatproperclearancesaremaintained.Extendchimneybyadd-

ing sections of double wall pipe until pipe is minimum of 30" above

highestpointofroofcutout.Terminationandchimneymustextend

a minimum of 36" above highest point where it passes through roof.

This manual suits for next models

Table of contents

Other Astria Indoor Fireplace manuals

Astria

Astria Gemini33TMN User manual

Astria

Astria Envy35TEN Supplement

Astria

Astria MontebelloDLX40TEN User manual

Astria

Astria Craftsman 36P2 User manual

Astria

Astria london lights User manual

Astria

Astria Wood burning fireplace Assembly instructions

Astria

Astria montecito User manual

Astria

Astria Sentinel36TEN User manual

Astria

Astria MONTECITO MONTE User manual

Astria

Astria MontebelloSTTYN User manual

Astria

Astria VILLA VISTA User manual

Astria

Astria Eros35STDMN User manual

Astria

Astria Envy35xxx series User manual

Astria

Astria Ladera-BK User manual

Astria

Astria Georgian 42 User manual

Astria

Astria MontebelloDLX40TEN User manual

Astria

Astria MONTECITO ESTATE User manual

Astria

Astria MontebelloDLX40TYN User manual

Astria

Astria Paris Lights 43ZMN User manual

Astria

Astria MONTEBELLO ST Parts list manual

Astria

Astria Eros35STDMN User manual

Astria

Astria Marquee36 User manual

Astria

Astria MM33 User manual

Astria

Astria 126730-01 Owner's manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual