Astria Alpha32ZEN User manual

Installation and Operation Instructions

Unvented (Vent-Free) Radiant Faced and Louvered

Fireplace System with Logs and Thermostat Blower

P/N 126878-01 REV. B 05/2017

Models

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

This appliance may be installed in an aftermarket permanently located, manufactured (mobile) home,

where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the

rating plate. This appliance is not convertible for use with other gases.

This is an unvented gas-ﬁred heater. It uses air (oxygen) from the room in which it is installed. Provisions

for adequate combustion and ventilation air must be provided. Refer to Air for Combustion and Ventilation

section on Page 7 of this manual.

PFS

Report No. F12-047

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death, or property damage.

- Do not store or use gasoline or other ﬂammable vapors and liquids in the vicinity of this or any other

appliance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁre department.

- Installation and service must be performed by a qualiﬁed installer, service agency or the gas supplier.

Alpha32ZEN

Alpha32ZEP

Alpha36ZEN

Alpha36ZEP

BisonMtn18

For use with log set (required option)

P126878-01

Astria.us.com 126878-01B2

TABLE OF CONTENTS

Safety .................................................................. 2

Product Identiﬁcation........................................... 4

Local Codes......................................................... 5

Unpacking............................................................ 5

Product Features................................................. 6

Air For Combustion and Ventilation..................... 7

Installation ........................................................... 9

Operation........................................................... 23

Inspecting Burners............................................. 30

Cleaning and Maintenance................................ 31

Wiring Diagram.................................................. 32

Speciﬁcations .................................................... 33

Troubleshooting................................................. 34

Replacement Parts............................................ 41

Service Hints ..................................................... 41

Technical Service............................................... 41

Accessories....................................................... 41

Parts.................................................................. 42

Warranty............................................................ 47

SAFETY

Carbon Monoxide Poisoning: Early signs

of carbon monoxide poisoning resemble the

ﬂu, with headaches, dizziness, or nausea. If

you have these signs, the heater may not be

workingproperly.Getfreshair at once!Have

heater serviced. Some people are more af-

fectedby carbonmonoxide thanothers.These

include pregnant women, people with heart or

lung disease or anemia, those under the inﬂu-

ence of alcohol, and those at high altitudes.

Natural and Propane/LP Gas: Natural and

propane/LP gases are odorless. An odor-

making agent is added to the gas. The odor

helps you detect a gas leak. However, the

odor added to the gas can fade. Gas may be

present even though no odor exists.

Make certain you read and understand all

warnings. Keep this manual for reference.

It is your guide to safe and proper operation

of this heater.

WARNING: FIRE, EXPLOSION, AND ASPHYXIATION HAZARD

Improperadjustment,alteration,service,maintenance,orinstallationofthis

heater or its controls can cause death or serious injury.

Read and follow instructions and precautions in User’s Information Manual

provided with this heater.

WARNING: This is an unvented

gas-ﬁredheater.Itusesair(oxygen)

fromtheroominwhichitisinstalled.

Provisionsforadequatecombustion

andventilationairmustbeprovided.

Refer to Air for Combustion and

Ventilation section on Page 7 of

this manual.

Thisappliancemaybeinstalledinan

aftermarket,* permanently located,

manufactured(mobile)home,where

not prohibited by local codes.

This appliance is only for use with

the type of gas indicated on the

rating plate. This appliance is not

convertibleforusewithothergases.

* Aftermarket: Completion of sale, not for

purpose of resale, from the manufacturer

WARNING:Thisproductcontains

and/or generates chemicals known

to the state of California to cause

cancer or birth defects or other re-

productive harm.

DANGER: Carbon monoxide

poisoning may lead to death!

WARNING:Vent-freeproductsare

prohibitedforbedroomandbathroom

installation in the Commonwealth of

Massachusetts.

Astria.us.com

126878-01B 3

SAFETY

Continued

IMPORTANT: Read this owner’s

manual carefully and completely

beforetryingtoassemble,operateor

service this ﬁreplace. Improper use

of this ﬁreplace can cause serious

injury or death from burns, ﬁre, ex-

plosion,electricalshockandcarbon

monoxide poisoning.

WARNING: Any change to this

heater or its controls can be dan-

gerous.

WARNING: Do not use a blower

insert,heatexchangerinsertorother

accessorynotapprovedforusewith

this heater.

Due to high temperatures, the ap-

pliance should be located out of

trafﬁc and away from furniture and

draperies.

Do not place clothing or other ﬂam-

mable material on or near the appli-

ance. Never place any objects on

the heater.

Fireplace front and screen become

very hot when running ﬁreplace.

Keep children andadults away from

hotsurfacestoavoidburnsorcloth-

ing ignition. Fireplace will remain

hot for a time after shutdown.Allow

surfaces to cool before touching.

Young children should be carefully

supervisedwhentheyareinthesame

room with the appliance. When us-

ingthehand-heldremoteaccessory,

keepselectorswitchintheOFFposi-

tiontopreventchildrenfromturning

on burners with remote.

Youmustoperatethisheaterwiththe

ﬁreplace screen and hood in place

before running heater. The ﬁreplace

screenshallhaveopeningsforintro-

duction of combustion air.

Keep the appliance area clear and

free from combustible materials,

gasolineandotherﬂammablevapors

and liquids.

WARNING: Do not allow fans

to blow directly into the ﬁreplace.

Avoid any drafts that alter burner

ﬂame patterns. Ceiling fans can

create drafts that alter burner ﬂame

patterns.Alteredburnerpatternscan

cause sooting.

WARNING: Do not place log

scraps or volcanic stone on burner.

Solid-fuels shall not be burned in a

ﬁreplaceinwhichanunventedroom

heater is installed.

2. Do not place propane/LP supply tank(s)

inside any structure. Locate propane/

LP supply tank(s) outdoors (propane/LP

only).

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touchany electrical switch; donot

use any phone in your building

1. WARNING: Thisappliance is onlyfor

use with the type of gas indicated on

the rating plate.This appliance isnot

convertible for use with other gases.

Installation and repair should be

done by a qualiﬁed service person.

The appliance should be inspected

before use and at least annually by

aprofessionalserviceperson.More

frequent cleaning may be required

duetoexcessivelintfromcarpeting,

beddingmaterial,etc.Itisimperative

thatcontrolcompartments,burners,

and circulating air passageways of

the appliance be kept clean.

Astria.us.com 126878-01B4

SAFETY

Continued

• immediately call your gas supplier from

aneighbor’sphone.Followthegassup-

plier’s instructions

• if you cannot reach your gas supplier,

call the ﬁre department

4. This ﬁreplace shall not be installed in a

bedroom or bathroom.

5. Do not use this ﬁreplace as a wood-burn-

ing ﬁreplace. Use only the logs provided

with the ﬁreplace.

6. Do not add extra logs or ornaments such

as pine cones, vermiculite, or glowing

embers. Using these added items can

cause sooting. Do not add volcanic stone

around base. Volcanic Stone and debris

couldfallintothe control area of ﬁreplace.

7. This ﬁreplace is designed to be smoke-

less. If logs ever appear to smoke, turn

off ﬁreplace and call a qualiﬁed service

person.

NOTE: During initial operation, slight

smokingcouldoccur duetolog curing and

ﬁreplaceburning manufacturing residues.

8. To prevent the creation of soot, follow the

instructionsinCleaning andMaintenance,

Page 31.

9. Before using furniture polish, wax, carpet

cleaner, or similar products, turn heater

off.If heated, the vapors from these prod-

ucts may create a white powder residue

within burner box or on adjacent walls or

furniture.

10. Thisﬁreplaceneedsfreshair ventilationto

runproperly.Thisﬁreplacehasan Oxygen

Depletion Sensing (ODS) safety shutoff

Figure 1 - Log Base Assembly

PRODUCT IDENTIFICATION

Log Set

Base

Assembly

Front

Burner

Remote

Control

Figure 2 - Fireplace

Cont.

SM TW T FS

ROOM

SET

Pilot

ON THERMO OFF

PROGRAM

MODE/SET

Top Outer Casing

Top panel

Assembly

Fireplace

Hood

Bottom Panel

Assembly

Screen

Assembly

Magnet

Left Side

Right

Side

Front

system.TheODSshutsdown theﬁreplace

if not enough fresh air is available.

See Air for Combustion and Ventilation,

Page 7.Ifﬁreplace keepsshuttingoff,see

Troubleshooting, Page 34.

11. Do not run ﬁreplace

• where ﬂammable liquids or vapors are

used or stored.

• under dusty conditions.

12. Do not use this ﬁreplace to cook food or

burn paper or other objects.

13. Do not use ﬁreplace if any part has been

under water. Immediately call a qualiﬁed

service technician to inspect the room

ﬁreplace and to replace any part of the

controlsystem and any gas control which

has been under water.

14. Turn off and unplug fireplace and let

cool before servicing. Only a qualiﬁed

service person should service and repair

ﬁreplace.

15. Operating ﬁreplace above elevations of

4,500 feet could cause pilot outage.

16. Do not operate fireplace if any log is

broken. Do not operate ﬁreplace if a log

is chipped (dime-sized or larger).

17. Toprevent performance problems, do not

usepropane/LPfuel tank of lessthan100

lbs. capacity (propane/LP only).

18. Provide adequate clearances around air

openings.

19. The screen or any other part removed

for servicing must be replaced prior to

operating this heater.

Astria.us.com

126878-01B 5

LOCAL CODES

UNPACKING

2. Locate two screws above top corners of

the ﬁreplace screen. Remove and discard

thesescrews.Push the bottom corners of

thescreeninandrelease.The screenwill

pop out at the bottom. Grasp the bottom

of the screen, lift the screen up and pull

out to remove.

3. Remove protective packaging applied to

logs, log base assembly, and ﬁreplace.

4. Remove fireplace hood from carton

inserts.

5. Checkall items for any shipping damage.

Ifdamaged,promptly inform dealerwhere

you purchased the ﬁreplace.

Install and use ﬁrebox with care. Follow all

local codes. In the absence of local codes,

usethelatest editionofThe NationalFuelGas

Code ANS Z223.1/NFPA 54*. Firebox must

be electrically grounded in accordance with

the National Electrical Code, ANS/NFPA70

(latest edition).

NOTE: Where listed vented decorative logs

are required, thermostat operation is not

permitted.

COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS

These appliances are approved for installation in the US state of Massachusetts if the fol-

lowing additional requirements are met:

• Un-vented Room Heaters shall be installed in accordance with 527 CMR 30.

• Installation and repair must be done by a plumber or gas ﬁtter licensed in the Common-

wealth of Massachusetts.

• Theﬂexiblegasline connector used shall notexceed36inches(92centimeters) in length.

• The individual manual shut-off must be a T-handle type valve.

• Unvented appliances may NOT be installed in bedrooms or bathrooms.

• A working smoke detector must be installed in the area where vent-free appliances are

installed.

Seller of unvented propane or natural gas-ﬁred supplemental room heaters shall provide

to each purchaser a copy of 527 CMR 30 upon sale of the unit.

*Available from:

American National Standards Institute, Inc.

25 West 43rd Street, 4th ﬂoor

New York, NY 10036

National Fire Protection Association, Inc.

1 Batterymarch Park

Quincy, MA 02169-7471

CAUTION:Donotremovethe

dataplatesattachedtotheheater

base assembly. The data plates

contain important warranty and

safety information.

1. With utility knife, cut the carton all the way

around above the staples on the bottom

tray. Lift the carton off the heater. Remove

packing.

NOTE: The hood is located in the packing

on the right hand side of the heater front.

Lift the heater off the bottom tray.

Astria.us.com 126878-01B6

PRODUCT FEATURES

OPERATION

This vent-free ﬁreplace is clean burning. It

requires no outside venting. There is no heat

loss out a vent or up a chimney. Heat is gen-

erated by both realistic ﬂames and glowing

embers. When used without the blower, the

ﬁreplace requires no electricity making it ideal

for emergency backup heat.

SAFETY DEVICE

This ﬁreplace has a pilot with an Oxygen

Depletion Sensing (ODS) safety shutoff

system. The ODS/pilot is a required feature

for vent-free room heaters. The ODS/pilot

system shuts off the ﬁreplace if there is not

enough fresh air.

ELECTRONIC IGNITION SYSTEM

This heater has an electronic igniter to light

the ﬁreplace's fuel supply.

BLOWER ASSEMBLY

Thisﬁreplaceincludesablowerassembly.The

blower operates thermostatically and features

avariablespeedcontrol.Theblowercirculates

heated air from the ﬁreplace into the room.

Astria.us.com

126878-01B 7

Unusually tight construction is deﬁned as

construction where:

a. walls and ceilings exposed to the out-

side atmosphere have a continuous

water vapor retarder with a rating of one

perm (6 x 10-11 kg per pa-sec-m2) or less

with openings gasketed or sealed and

b. weather stripping has been added on

openable windows and doors and

c. caulking or sealants are applied to

areas such as joints around window

and door frames, between sole plates

and ﬂoors, between wall-ceiling joints,

between wall panels, at penetrations for

plumbing, electrical, and gas lines, and

at other openings.

If your home meets all three criteria above,

you must provide additional fresh air. See

Ventilation Air From Outdoors, Page 9.

Ifyourhome doesnotmeet all three criteria

above, proceed to Determining Fresh-Air

Flow For Heater Location.

Conﬁned and Unconﬁned Space

The National Fuel Gas Code, ANSI Z223.1/

NFPA54 allows two methods for determining

whether the space in which the heater is being

installed is conﬁned or unconﬁned space. The

standardmethoddeﬁnesaconﬁnedspaceasa

space whose volume is less than 50 cubic feet

per1,000Btuperhour(4.8m3perkw)oftheag-

gregateinputratingofall appliancesinstalledin

thatspaceandanunconﬁnedspaceasaspace

whose volumeis notless than50 cubic feetper

1,000 Btu per hour (4.8 m3per kw) of the ag-

gregateinputratingofall appliancesinstalledin

thatspace.Roomscommunicatingdirectlywith

thespaceinwhichtheappliancesareinstalled*,

through openings not furnished with doors, are

considered a part of the unconﬁned space.

Where the air inﬁltration rate of a structure is

known,theKnownAir Inﬁltration RateMethod

may be used. Follow The National Fuel Gas

Code, ANSI Z223.1/NFPA 54 to use this

method to determine if the space is conﬁned

or unconﬁned.

* Adjoining rooms are communicating only if

therearedoorless passagewaysorventilation

grills between them.

DETERMINING FRESH-AIR FLOW

FOR FIREPLACE LOCATION

Determining if You Have a Conﬁned or

Unconﬁned Space Using the Standard

Method

AIR FOR COMBUSTION AND VENTILATION

Today’s homes are built more energy efﬁcient

thanever.Newmaterials,increasedinsulation,

and new construction methods help reduce

heat loss in homes. Homeowners apply

weather strip and caulk around windows and

doors to keepthe cold air out andthe warm air

in. During heating months, homeowners want

their homes as airtight as possible.

While it is good to make your home energy

efﬁcient, your home needs to breathe. Fresh

air must enter your home.All fuel-burning ap-

pliancesneedfreshairforproper combustion

and ventilation.

Exhaust fans, some ﬁreplaces, clothes dryers

and some fuel-burning appliances draw air

from the house to operate. You must provide

adequate fresh air for these appliances. This

will ensure proper venting of vented fuel-

burning appliances.

PROVIDING ADEQUATE

VENTILATION

Thefollowingareexcerptsfrom National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Air for

Combustion and Ventilation.

All spaces in homes fall into one of the three

following ventilation classiﬁcations:

1. Unusually Tight Construction

2. Unconﬁned Space

3. Conﬁned Space

The information on Pages 7–9 will help you

classify your space and provide adequate

ventilation.

Unusually Tight Construction

The air that leaks around doors and windows

may provide enough fresh air for combustion

and ventilation. However, in buildings of un-

usually tight construction, you must provide

additional fresh air.

WARNING: This heater shall not

be installed in a room or space un-

less the required volume of indoor

combustion air is provided by the

method described in the National

Fuel Gas Code, ANSI Z223.1/NFPA

54, the International Fuel Gas Code,

or applicable local codes. Read the

following instructions to ensure

properfreshair for this and other fuel-

burning appliances in your home.

Astria.us.com 126878-01B8

Use this work sheet to determine if you have

a conﬁned or unconﬁned space.

Space: Includesthe roomin whichyouwill install

ﬁreplace plus any adjoining rooms with door-

less passageways or ventilation grills between

the rooms.

1. Determine the volume of the space (length

x width x height).

Lengthx Width xHeight =__________cu. ft.

(volume of space)

Example:Space size 20 ft. (length) x 16 ft.

(width) x 8 ft. (ceiling height) = 2,560 cu. ft.

(volume of space)

If additional ventilation to adjoining room

is supplied with grills or openings, add the

volume of these rooms to the total volume

of the space.

2. Multiply the space volume by 20 to determine

the maximum Btu/Hr the space can support.

________ (volume of space) x 20 = (Maxi-

mum Btu/Hr the space can support)

Example:2,560 cu. ft. (volume of space) x

20 = 51,200 (maximum Btu/Hr the space can

support)

3. Add the Btu/Hr of all fuel burning appliances

in the space.

Vent-free ﬁreplace _________Btu/Hr

Gas water heater* _________Btu/Hr

Gas furnace _________Btu/Hr

Vented gas heater _________Btu/Hr

Gas ﬁreplace logs _________Btu/Hr

Other gas appliances* +________ Btu/Hr

Total =________Btu/Hr

* Do not include direct-vent gas appliances.

Direct-vent draws combustion air from the

outdoors and vents to the outdoors.

Example:

Gas water heater _____________Btu/Hr

Vent-free ﬁreplace+ ___________ Btu/Hr

Total =____________Btu/Hr

4. Compare the maximum Btu/Hr the space

can support with the actual amount of Btu/

Hr used.

_______ Btu/Hr (maximum the space can

support)

_______ Btu/Hr (actual amount of Btu/Hr

used)

Example:51,200 Btu/Hr (maximum the

space can support)

73,000 Btu/Hr (actual amount of

Btu/Hr used)

The space in the example is a conﬁned space

because the actual Btu/Hr used is more than the

maximum Btu/Hr the space can support. You

must provide additional fresh air. Your options

are as follows:

AIR FOR COMBUSTION AND VENTILATION

Continued

40,000

33,000

73,000

Figure 3 - Ventilation Air from Inside

Building

Remove

Door into

Adjoining

Room,

Option

Ventilation Grills

Into Adjoining Room,

Option 2

Ventilation

Grills Into

Adjoining

Room,

Option 1

12"

A. Rework worksheet, adding the space of an

adjoiningroom.Iftheextraspaceprovidesan

unconﬁned space, remove door to adjoining

room or addventilation grills betweenrooms.

See Ventilation Air From Inside Building.

B. Vent room directly to the outdoors. See

Ventilation Air From Outdoors Page 9.

C. Install a lower Btu/Hr ﬁreplace, if lower Btu/

Hr size makes room unconﬁned.

If the actual Btu/Hr used is less than the maxi-

mum Btu/Hr the space can support, thespace is

anunconﬁned space.You willneed noadditional

fresh air ventilation.

WARNING: If the area in which

the heater may be operated does not

meet the required volume for indoor

combustion air, combustion and

ventilation air shall be provided by

one of the methods described in the

NationalFuel Gas Code,ANSIZ223.1/

NFPA 54, the International Fuel Gas

Code, or applicable local codes.

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining

unconﬁned space. When ventilating to an

adjoiningunconﬁnedspace,youmust provide

twopermanent openings:onewithin 12"ofthe

ceiling and one within 12" of the ﬂoor on the

wall connecting the two spaces (see options

1and2,Figure 3).You can alsoremovedoor

into adjoining room (see option 3, Figure 3).

Astria.us.com

126878-01B 9

INSTALLATION

CAUTION:Thisﬁreplacecre-

ates warm air currents. These

currents move heat to wall sur-

facesnexttoﬁreplace.Installing

ﬁreplace next to vinyl or cloth

wall coverings or operating

heater where impurities (such

as, but not limited, to tobacco

smoke,aromaticcandles,clean-

ingﬂuids,oilorkerosenelamps,

etc.)intheairexist,maydiscolor

walls or cause odors.

NOTE: Your fireplace is designed to be

used in zero clearance installations. Wall

or framing material can be placed directly

against any exterior surface on the rear,

sides, or top of your ﬁreplace, except where

standoff spacers are integrally attached.

Where standoff spacers are attached to your

ﬁreplace, combustible material (studs and

wall board) may be place on top and above

the top of the standoffs.

Usethe dimensionsshownforroughopenings

to create the easiest installation. See Built-In

Fireplace Installation, Page 12.

IMPORTANT:Vent-free heatersaddmoisture

totheair.Althoughthis is beneﬁcial, installing

ﬁreplace in rooms without enough ventilation

air may cause mildew to form from too much

moisture.SeeAir forCombustionandVentila-

tion, Page 7.

IMPORTANT:Makesuretheﬁreplaceislevel.If

ﬁreplaceisnotlevel,logsetwillnotworkproperly.

Figure 4 - Ventilation Air from Outdoors

Outlet

Air

Ventilated

Attic

Outlet

Inlet

Air

Inlet Air Ventilated

Crawl Space

Crawl

Space

To Attic

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation

grills or ducts. You must provide two perma-

nent openings: one within 12" of the ceiling

andonewithin12"oftheﬂoor. Connect these

items directly to the outdoors or spaces open

to the outdoors. These spaces include attics

and crawl spaces. Follow the National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Air for

Combustion and Ventilation for required size

of ventilation grills or ducts.

IMPORTANT: Do not provide openings

for inlet or outlet air into attic if attic has a

thermostat-controlled power vent. Heated air

entering the attic will activate the power vent.

NOTICE: This appliance is in-

tended for supplemental heat-

ing. Use this heater along with

yourprimaryheatingsystem.Do

notinstallthisheaterasyourpri-

mary heat source. If you have a

centralheatingsystem,youmay

run system’s circulating blower

whileusingheater.Thiswillhelp

circulatetheheatthroughoutthe

house. In the event of a power

outage, you can use this heater

as your primary heat source.

WARNING: A qualiﬁed ser-

vice person must install ﬁre-

place. Follow all local codes.

WARNING: Never install the

ﬁreplace

• in a bedroom or bathroom

• in a recreational vehicle

• where curtains, furniture,

clothing, or other ﬂammable

objects are less than 36" from

the front and 42" from the top

of ﬁreplace. For side clear-

ances see Figure 8, Page 11

• in high trafﬁc areas

• in windy or drafty areas

AIR FOR COMBUSTION AND VENTILATION

Continued

Astria.us.com 126878-01B10

Figure 5 - Installing Hood

Screw

Hood

Rail

INSTALLATION

Continued

Figure 6 - Assembling Perimeter Trim

Side Trim

Slot

Mitered

Edge

Slot

Shim

Set Screws

Adjusting

Plate

Assembled

Trim

Top

Trim

Figure 7 - Attaching Perimeter Trim to

Fireplace

Trim

Hanging

Screws

Hanging

Notches

on Trim

Mitered

Edge

ASSEMBLING AND ATTACHING

OPTIONAL PERIMETER TRIM

(Included with Mantel Accessory)

IMPORTANT: Ifyouarerecessingtheﬁrebox

in a wall, do not attach trim at this time. See

Built-In Fireplace Installation,Page 12.

NOTE: These instructions show assembling

and attaching trim to ﬁreplace.

CHECK GAS TYPE

Use the correct gas type (natural or propane/

LP)foryourﬁreplace. If your gas supplyisnot

correct, do not install ﬁreplace. Call dealer

where you purchased ﬁreplace for proper

type ﬁreplace.

WARNING:Thisapplianceis

equippedfornaturalorpropane/

LP gas but not both. Gas type is

indicated on rating plate. Field

conversion is not permitted.

ELECTRICAL HOOKUP

This ﬁreplace includes a blower which must

be connected to either a wall receptacle or

theelectricalreceptaclethatisincludedwithin

the ﬁreplace. If the receptacle included with

the ﬁreplace is to be used, it must be wired

to a 120 volt supply by a certiﬁed electrician.

INSTALLING HOOD

Installhoodto railalreadyinstalledin ﬁreplace

as shown in Figure 5. Use 3 Phillips screws

provided.

1. Remove packaging from three pieces

of trim.

2. Locate four screws, two adjusting plates

with set screws, and two shims in the

hardware packet.

3. Alignshimunderadjusting plateasshown

in Figure 6.

4. Slide one end of adjusting plate/shim

in slot on mitered edge of top trim (see

Figure 6).

5. Slide other end of adjusting plate/shim

in slot on mitered edge of side trim (see

Figure 6).

6. While firmly holding edges of trim to-

gether, tighten both set screws on the

adjusting plate with slotted screwdriver.

7. Repeat steps 1 through 6 for other side.

8. Tighten trim hanging screws (#10 x 6.25

shoulder) into holes in cabinets. Place

the assembled trim onto ﬁreplace cabi-

net. Align hanging notches on trim with

hanging screws on side of ﬁreplace (see

Figure 7).Pushtrim ﬁrmly intoplace,slid-

inghanging notchesoverhanging screws.

This manual suits for next models

Table of contents

Other Astria Indoor Fireplace manuals

Astria

Astria StarLite36WS User manual

Astria

Astria Eros35STDMN User manual

Astria

Astria Zeta21ZMN F1241 User manual

Astria

Astria TaurusPFZ Owner's manual

Astria

Astria Craftsman STP2 User manual

Astria

Astria Eros35STDMN User manual

Astria

Astria MontebelloDLX40TEN User manual

Astria

Astria MontebelloSTTEP User manual

Astria

Astria Gamma26ZTN User manual

Astria

Astria Georgian 42 User manual

Astria

Astria CraftsmanCat 36P2 User manual

Astria

Astria MONTECITO ESTATE User manual

Astria

Astria MONTECITO MONTE User manual

Astria

Astria Envy35xxx series User manual

Astria

Astria Ladera CAT User manual

Astria

Astria MONTEBELLO ST Parts list manual

Astria

Astria Devonshire36TEN User manual

Astria

Astria MM33 User manual

Astria

Astria 126730-01 Owner's manual

Astria

Astria VILLA VISTA User manual

Astria

Astria MMST43 User manual

Astria

Astria BerlinLights43ZEP User manual

Astria

Astria MontebelloSTTEN User manual

Astria

Astria Rhapsody42TEN User manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual