ASTRALVISION AVSN Series User manual


Table of Contents
Warning Notices 3
Ventilation 4
External Connectivity & Characteristics 5
Interface Panel Details 6
Remote Control Functions 7
Basic Operation 8
Start Up & Shut Down 8
Calibration 9
Optional OPS PC 11
Smartbar 11
Home Page 12
Task Manager 14
Whiteboard Mode 15
Gallery 18
File Manager 19
System Settings 21
Set Time/Date 22
Network 23
Input Method 25
Printer 27
Language 28
Clear Screenshots 28
Auto Luminance 29
Restore Default Setting 30
Browser 31
Listen Alone 31
Programs 32
Calculator 33
Clock 33
Music 34
ES File 34
Temperature Measuring 35
Select Signal Channel 35
Menu 36
Image 36
Sound Mode 37
Setting 37
Time 38
Parent Control 38
ECO Mode 39
Serial Port Control 39
Specifications of PC Mode (VGA Input) 41
Formats Supported by USB Mode 42
FAQs & Troubleshooting 42
Instructions in Provisions for Recycling and Disposal of
Waste Electrical and Electronic Products 44
Maintenance Tips 44
- 2 -

- 3 -
WARNING NOTICES
The power supply voltage is 240V AC & is high enough to cause personal injury.
Do not use any types of power cable other than an approved Australian IEC cable
to prevent the product from being damaged.
Do not open the enclosure unless you are an authorised service engineer.
Check if the electrical supply power socket voltage is 240V AC 50 Hz, that complies
with the product’s receiving power supply before use. Disconnect the product from
the power supply if the product is not to be used in a long period of time.
Disconnect the product from power supply and stop using it if you sense any
abnormal sound or smell emitted by the product. Contact your supplier for
advice and/or service.
Do not let any liquid and metal object go into the product. If any liquid or metal object
goes into the product, cut off the power and contact your Dealer or ABI foradvice
and/or service.
Do not place the product on an unstable stand, bracket or table. Otherwise, it may fall
off and cause personal injury. A range of stands & brackets designed for this product
are available from your supplier.
When on a mobile stand, move the product carefully to prevent it from being knocked
or bumped in any way. This may cause damage to the panel and/or injury.
Mount the product as instructed and using only mounting accessories recommended
by the manufacturer.
When wall mounting, the touchscreen should be mounted on a solid wall that can
bear over four times of the weight of the panel. Ensure proper ventilation. You
should assess the bearing capability of the wall before mounting the product on a
special wall such as a steel-structure, plasterboard, glass, etc.

- 4 -
Ventilation:

Outer Appearance
(Front view)
(Lower view)
Left 15W speaker Right 15W speaker
Control & Connectivity panel
Connectivity
Interface
(Left View) (Rear View) (Right View)
Connectivity
Interface
OPS PC slot
Power socket
- 5 -

- 6 -
2 3 4 5 61 87
Control Panel
1]. Home: Open the Android home page.
2]. Back: Go back or return to the parent menu.
3]. HDMI 1: Switch over to HDMI 1 signal source channel.
4]. ECO: Switch over to ECO, Auto or Standard mode.
5]. Signal: Show or exit from the list of signal sources.
6]. VOL+: Increase the volume.
7]. VOL-: Decrease the volume.
8]. PC Power: Turn on/off the OPS module PC.
Connectivity Panels:
Bottom Panel
Left Side Panel

- 7 -
Functions of the Remote Control
1. : On/standby
2. : Mute
3. 0—9: Select TV channel or enter number
4. (Home): Open the Android home page.
5. (Return): Go back or return to the parent menu.
6. (Menu): Show or hide menu.
7. : Show or exit from the list of signal sources.
8. : Enable Audio mode.
9. (Freeze): Freeze the frame.
10. : Up/Down/Left/Right direction buttons
11. (OK): Confirm OK.
12. (Capture): Capture image of current screenshot.
13. (Display): Show the current signal source. You cannot show it in Android.
14. (Auto): Auto adjust screen display.
15. (WIFI): Open WiFi on the computer.
16. (ECO): Change the display back light mode.
17. (Pg Up): Turn to the previous page on white board software and PPT.
18. (Pg Dn): Turn to the next page on white board software and PPT.
19. (Notes): Open white board software.
20. (PC): Switch over to VGA signal source.
21. (HDMI): Switch over to HDMI signal source.
22. (OPS): Switch over to OPS PC signal source.
23. (Zoom): Zoom in and out.

- 8 -
Basic Operation
Start Up
Power the touchscreen with 240V 50Hz AC power supply.
Connect the panel to the power supply. Switch on the rocker switch (on the left of the
rear of the panel, next to the power cable port) to enter the standby status. The
power LED turns red.
Press Power on the control panel or Standby on the remote control to turn on the
touchscreen. The power LED turns green.
Shutdown
Press PC Power to turn off the OPS computer (if OPS connected).
Press Power on the control panel or Standby on the remote control to enter the
standby status. The power LED turns red.
Under the standby status, switch off the rocker switch to turn off the interactive panel.
Important:
1] Turn off the OPS computer before the touchscreen. Otherwise, the computer can be
damaged.
2] Disconnect the interactive panel from power after the panel enters standby status.
Otherwise, the panel can be damaged. A sudden power failure can damage the
touchscreen.
Calibration with Windows or Mac/Linux Driver
To ensure that the handwriting display works properly, you need to make the handwriting
shown on the display coincides with the actual handwriting and ensure accurate
positioning of the cursor on the screen. You need to calibrate under the following
circumstances:
When you first use the interactive LED display.
Re-install the drive program.
When you connect the display to another PC.

- 9 -
Calibration for Windows 7/8:
1. Connect the interactive panel to PC using the USB lead via the USB interface on the
panel;
2. Select Tablet PC Setting on Control Panel.
1. Select on the setting window.

- 10 -
Use the pen to click and hold the center of the cross. Do not release it until the cross
moves to the next positioning point. Complete the positioning process as instructed.
Click Yes after it completes
Hits & Tips
To ensure the handwriting accuracy, use the pen provided with the interactive panel
rather than a finger to perform positioning.
Positioning errors may cause touch functions of the interactive panel to be inaccurate.
In that case, please re-calibrate following above instructions.
If the PC has been previously calibrated to a different device, a “reset” should be done
in the calibration window to allow a full 16-point calibration to prevent conflicts.
Tap ESC on the keyboard during the positioning process to escape from positioning.
The positioning interface varies between different software versions. Please follow
instructions provided on the actual interface.
Table of contents
Other ASTRALVISION Touch Panel manuals
Popular Touch Panel manuals by other brands

IBASE Technology
IBASE Technology ASTUT-152-RE1S user manual

YASKAWA
YASKAWA TP 610C manual

B&R
B&R Power Panel C Series user manual

Beijer Electronics
Beijer Electronics X2 control Hardware and installation manual

AXIOMTEK
AXIOMTEK GOT321W-521 user manual

TRIDONIC.ATCO
TRIDONIC.ATCO x-touchBOX Operation manual












