Assa Abloy Sargent 9700 Instruction Manual

Instructions for installing the 9700/12-9700

Surface Vertical Rod Exit Device

FOR ASSISTANCE, CALL SARGENT AT 1-800-727-5477 o www.sa gentlock.com

Top case

chassis

Center case

chassis

Bottom case

chassis

Bottom case

cover

Cross bar

Center

case cover

Top case

cover

Bracket

cover

Bracket

chassis

*NOTE: 12-9700 shown

CAUTION: CHECK BEFORE STARTING DOOR PREP

Door should be fitted and hung. Check box label for size of exit device, function, hand and design.

Surface of the door must be flush. Clear away

any raised projections to allow exit device to rest

on flat surface of the door.

THIS EXIT DEVICE IS NON-HANDED

Right hand

reverse bevel

eft hand

reverse bevel

OUT



Tools required

1. Measuring tape

2. Power drill

3. Drill bits:

3/32", 1/4", 11/32", 3/8", #25

4. Taps: #10-24

5. Screwdrivers: Phillips #2 and #3

Top rod

Rod guide

Bottom rod

Rod guide

Cross bar plug

A5570G 5-5-09

Reproduction in whole or in part without the expre written permi ion of Sargent Manufacturing Company i prohibited.

All 9700/12-9700 Exit Devices are not handed and can be used on

either hand door.

NOTE: Trim may or may not be handed

9700/12-9700 Vertical Rod Exit Device

ark vertical centerline on inside of door

as follows:

A. Where the lock stile is approx.

4-1/2" wide or wider - “A” = 2-3/4"

B. On single doors where the width of lock

stile is under 4-1/2", make "A" equal to

1/2 the width of the exposed lock stile

(when door is closed against stop)

Finished floor

“A”

Inside

face of

door

Vertical C

of top, bottom & center case

Door

Stop

5/8"

Max

Locate and place templates as follows:

A. With door closed, tape top case template

to inside of door along reference lines

marked in step 1

B. Tape center case template to door in the

same manor (see dimension on template

to obtain correct height from finished floor)

C. Using cross bar hole centers for

measuring, locate vertical center line of

bracket (See dimensions on template to

obtain correct height from finished floor)

Door stop Top case

template

Stop

thickness

Vertical C

top, bottom and

center case

Obtain dimensions

to finished floor

from template

ocate templates between mounting holes on cross bar

Horizontal C

bracket holes

Drill and cut holes as directed on template

Attach outside trim when used

A. Some outside trims are through-bolted to the center

case. Trims of this type must be put on in conjunction

with step 5. Check outside trim used

B. Check for correct spindle or thumb-piece length

C. Install key cylinder (check for correct tail piece length)

1/8" gap min. between

lever and chassis

Reproduction in whole or in part without the expre written permi ion of Sargent Manufacturing Company i prohibited.

A5570G 5-5-09

9700/12-9700

Vertical Rod Exit Device

Remove cover from center case chassis and

mount chassis on door. Using (4) 10-24 flat

head machine screws or (4) # 10 flat head

wood screws

I PORTANT! On (12) 9706, (12) 9762,

(12) 9713 and (12) 9763 functions,

make sure key cylinder hub in

chassis is turned to correct position

before mounting chassis on door.

NOTE: (12) 9713 and (12) 9706 does

not have this hub assembly when

used with ET Trim. For (12) 9763/(12) 9713

long end of pin faces up.

Cylinder turns 360°

to the left or right.

For (12) 9762/(12) 9706

long end of pin faces down.

Cylinder turns 180°

in both directions.

Cylinder

hub

649 Standard strike for both 12- Fire

rated and standard top case

(2) 10-24 round head machine screws

(2) 10-24 oval head machine screws

ount bracket chassis on door using (4) 10-24 flat

head machine screws or (4) #10 flat head wood

screws and attach bracket cover to chassis using

(4) 8-32 oval head machine screws

Cover screws

ount top strike in position prepped in step 2

Tighten screws securely.

ount top case and rod

A. Make sure crossbar arm is not in lockdown position

B. Screw top rod into top case until finger tight

C. Slide top rod into main slide - do not pin in place

D. Attach top case at location prepped in step 2;

Note: Through-bolts required and supplied for

Fire Rated Top Case on wood doors

E. Unscrew top rod until top hole in rod is aligned with

hole in main slide and insert rod adjustment pin

Hub pin

down for 62

function

Hub pin

up for 63

function

Chassis

Through-bolts

standard for

fire rated doors

NOTE: 12 - Top case shown

NOTE: Use two (2) #10 steel screws and mortise nuts (when

provided) in the position illustrated in the top and bottom

chassis. Steel mortise nuts are twin knurled for identification.

Rod

adjustment pin

A5570G 5-5-09

Reproduction in whole or in part without the expre written permi ion of Sargent Manufacturing Company i prohibited.

• Apply covers using 8-32 oval under cut hard machine screws

• Attach guides using #10 Oval Head Screws, rods must move freely with guides

Slide crossbar into chassis and bracket arms and attach crossbar plugs

to crossbar using socket head cap screws

Adjustment

A. Fine adjustment is made by turning rod into case to shorten

or out of case to lengthen

B. Rough adjustment is made by changing hole used for

adjustment pin

9700/12-9700

Vertical Rod Exit Device

1/4"

1/8"

ortise applied strikes Surface applied

strike

624 Standard strike

(2) 12-24 flat head machine screws

(2) #12 flat head wood screws

647 14-Standard strike

(2) # 12 flat head wood screws

655 12-Standard

fire rated strike

(2) 1/4- 20 flat head

machine screw

Latch track thresholds

(by others)

Bottom Strikes

Mark and install according to appropriate template

and following notes

For surface applied strikes: 624, 647

1. Transfer vertical centerline to floor or threshold and mark

2. Center strike on line marked

3. Mark mounting holes

4. Drill holes for required fasteners

5. Mount strike with fasteners provided

6. Tighten screws securely

For mortised strike: 655 follow steps in section 9 above. Mark

mounting holes and outline of strike.

ount bottom rod assembly in the same manner as the top rod assembly and fasten bottom case chassis

1. Verify rail is not dogged

2. Screw rod into bottom

case until finger tight

3. Slide bottom rod into

main slide

4. Insert adjustment pin

into middle hole

5. Position bottom case on

door, centered on vertical

reference line. Raise or

lower to achieve gap

indicated for strike application

(see drawings below).

6. Drill and tap mounting holes

7. Mount bottom case

Tighten fasteners securely

A5570G 5-5-09

Rod adjustment pin

Reproduction in whole or in part without the expre written permi ion of Sargent Manufacturing Company i prohibited.

This manual suits for next models

Other Assa Abloy Lock manuals

Assa Abloy

Assa Abloy Corbin Russwin BLSS ML2000 Series User manual

Assa Abloy

Assa Abloy Yale YDM7220 User manual

Assa Abloy

Assa Abloy Corbin Russwin IN100 User manual

Assa Abloy

Assa Abloy G-S Instruction manual

Assa Abloy

Assa Abloy Lockwood Pentagon 3P70 User manual

Assa Abloy

Assa Abloy OneSystem 509N Installation instructions

Assa Abloy

Assa Abloy SARGENT FM7300 Series User manual

Assa Abloy

Assa Abloy IKON VERSO CLIQ V551 User manual

Assa Abloy

Assa Abloy APERIO E100 Scand User manual

Assa Abloy

Assa Abloy Yale YM Series User manual

Assa Abloy

Assa Abloy HES Aperio K100 Manual

Assa Abloy

Assa Abloy Corbin Russwin UT5200 Series Quick start guide

Assa Abloy

Assa Abloy ASSA Coded 1.2 Installation manual

Assa Abloy

Assa Abloy INTERLOCK P84166 User manual

Assa Abloy

Assa Abloy Aperio KS100 User manual

Assa Abloy

Assa Abloy LOCWOOD 001TOUCH User manual

Assa Abloy

Assa Abloy Securitron Magnalock Series User manual

Assa Abloy

Assa Abloy Effeff 519 User manual

Assa Abloy

Assa Abloy EL490 User manual

Assa Abloy

Assa Abloy Yale Real Living YRD210-ZW Technical specifications

Assa Abloy

Assa Abloy Yale Y-LL67AP User manual

Assa Abloy

Assa Abloy Effeff 843G User manual

Assa Abloy

Assa Abloy LSC 001T-1K1CPDP User manual

Assa Abloy

Assa Abloy SARGENT DL Series User manual

Popular Lock manuals by other brands

Magic

Magic 105 manual

Gantner

Gantner GAT NET.Lock 7020 System Installation, configuration & operation

Wittkopp

Wittkopp Insys 7202 manual

Dorma

Dorma Studio Classic Installation instruction

Securam

Securam ECSL-601 quick start guide

Sudhaus

Sudhaus 3003 operating manual

Safety 1st

Safety 1st 48517 user guide

Pado

Pado FDS-10 user manual

Esco

Esco systeQ Series installation instructions

COMPX

COMPX National D8951 instruction sheet

secureo

secureo Key Box instruction manual

Stock Loks

Stock Loks C8713 instruction sheet

COMPX

COMPX 1T-058 Information

Auslock

Auslock T11 user manual

ELCOM

ELCOM 7205 Operating instruction

Stealth SAFES

Stealth SAFES ShadowVault Instructions & Troubleshooting

Knox

Knox KeySecure 5 Admin & user guide

Kwikset

Kwikset 48334/01 Quick installation guide