Assa Abloy 840C-50 User manual

ASSA ABLOY, the global leader

in door opening solutions.

Motor Lock Manual

840C-50, 841C-50, 841C-35, 851C-35, 851C-50, 850C-50

ASSA ABLOY, the global leader in door

opening solutions, dedicated to satisfying

end-user needs for security, safety and

convenience.

ASSA AB

P.O. Box 371

SE-631 05 Eskilstuna

Sweden

phone +46 (0)16 17 70 00

fax +46 (0)16 17 72 10

Customer support:

phone +46 (0)771640640

fax +46 (0)16 17 73 72

e-mail: [email protected]

www.assa.se

För manual på svenska, var god vänd.

Installation .................... 3

Connection ................... 4

Factory reset .................. 4

Latch bolt 840C/850C ............ 5

Technical data.................. 6

Accessories ................... 7

Maintenance of motor locks........ 8

Class 4 och Class 5............... 9

SSF 3522 Mode................. 9

Accessories SSF 3522............. 9

Quick guide .................. 11

Contents

Order information:

Dokument XXXXXX

Artnr XXXXXX

Grafisk form: AB Typoform

©ASSA AB, 2016

Installation

1Mark centerline A (Face plate) when you have decided the position

of the lockcase.

2Mark B and C

3Use a 20 mm drill bit to get the correct depth for the lockcase, 82 mm

for 50 mm backset and 48 mm for 35 backset. Do not use force to push

the lockcase into the mortice.

4Drill the 42 mm hole (B and C) for cylinder and handle through the door.

5Mortice the center faceplate into the edge of the door, this has a depth of 3

mm and radius 11.

6Make the mortise for the striking plate. Drill 5 holes Ø20 with a depth of

26 mm. Use a chisel to fit the strike plate into the mortise. Use a chisel to

make the outer profile (depth 4 mm for 1487-X). Predrill the four holes

(Ø3 mm).

7If the internal door sensor is used. Mount the magnet into the striking

plate. The door sensor position is behind the date mark on the forend.

Assa recommends a clearance of 3 mm between forend of lock case

and strike plate.

Adjust the door seal pressure.

Before fitting the lock to a firesmoke resisting door, the fire certification

should be examined.

Connection

To connect a motor lock to the Hi-O bus a

four wire cable is used; two for power and

two for communication.

Use supplied cable EA226 (10m), with

connector, at installation.

The cable can be connected anywhere on

the Hi-O bus.

Factory reset

1Switch off power to the lock.

2Make sure that the door is open

(no magnet on the lock door sensor).

3Turn on power.

4Within 30 seconds, toggle / switch

group switch 6 times back and forth.

5Switch off the power.

6Turn on the power.

7Verify that the LED next to the group

switch is turned on ( Steady light).

Explanition for LED

• Steady light= Factory mode, not initiated

• LED off= Initiated

• Flashing LED (2Hz)= “Wrong DAC” lock

already initiated against another DAC.

• Flashing LED (10Hz)= Timeout wait 240 sec

(4 min) then initiate DAC or reset the lock.

See the quick guide.

White CAN high

Brown CAN low

Green + 12–24VDC stab

Yellow 0 V

1Unmount the screws (Torx T20).

2Be careful the pin and socket can fall out.

3Unmount the plastic.

4Turn the latchbolt.

5Assembly the plastic.

6Assembly the pin and socket.

7Assembly the forend.

8Assembly the screws (Torx T20).

Door monitor

The placement of the door monitor is under the date mark on the forend.

Latch bolt 840C/850C

1 2

Currency consumption (mA)

Lock Type Idle Running

Assa Motor Lock

841C/840C/850C/851C

50mA Max 445 mA at

24VDC

Cable

Type: EA226, 10 m

Max length Total 50 m

Cable length Cable area 12V

20 m 0,3 mm2

30 m 0,4 mm2

40 m 0,5 mm2

50 m 0,6 mm2

Contents in package

Complete package: Lock case, Drill protection, DAC-500,

Cable EA226, Strike plate, Magnet, Fitting screws, Manual

Half package: Lock case, Drill protection , Cable EA226,

Strike plate, Magnet, Fitting screws, Manual

Lock case: Lock case, Drill protection and Manual

DAC530 package: Lock case, DAC530, cable EA226,

Magnet for striking plate.

Technical data

ASSA 840C-50

841C-50

850C-50

851C-50

841C-35

851C-35

Cylinder type Round, oval Oval

Strike plate 1487-1, -2*, -3, -4, -5 1487-8*

Cable EA226* EA226*

Cable loop EA280, EA281* EA280, EA281*

Thumb turn Round thumb turn cyl. 13

Oval thumb turn cyl. 03

Cylinder accessories 3212 4559 SCD

Plastic dome accessory 8065, with round thumb

turn cyl.

–

Lever handle Standard / NA NA

Security accessories 4559 SCD

* Supplied in set packages

Accessories

Follow this manual thoroughly to

maintain characteristics of the motor

lock. Do not diverge from this manual

without advice from ASSA.

Warranty fails if product is:

• Wrong installed.

• Opened by unauthorised personnel

(broken seal) or if cables/connec-

tors has been cut.

• Fitted with accessories or parts not

recommended by ASSA.

Maintenance:

• Approximately twice a year, a small

amount of designated grease should

be applied on latches and bolts.

Highly frequented doors may need

maintenance with shorter intervals.

• Electric parts need NO maintenance.

• To maintain desired operation and

security level of installed unit, it is

of great importance to check and

adjust the entire door environment:

– Lock case and strike plate

– Lock accessories (Lever handle,

thumb turn etc.)

– Hinges, framework and door

threshold (sill).

– Door closer.

NB!!

• Never use lubricants containing

graphite or solvent, use designated

grease from ASSA only.

• If any uncertainty regarding instal-

lation, maintenance or warranty

occurs, please contact ASSA or your

local supplier.

• The safety features of this product

are essential to its compliance with

EN 14846. No modification of any

kind, other than those described in

these instructions, is permitted.

• The locks 841C and 851C must

always be combined with a door

closer which is proven by test to

keep a door in closed position in

the event of fire.

• The lock case is intended to sit in

single or double acting wooden,

aluminum or steel door.

Maintenance of motor locks

EN14846 -X8E----- (850C,851C,840C,841C) 0402-CPR-SC0155-14 CE

EN14846 3 X 8 E 0 L 7 1 3 (850C,851C) SC0860-14 Performance

EN14846 3 X 8 E 0 L 5 1 3 (840C,841C) SC0173-15 Performance

EN 50130-4 4P03456-E6 (841C-35,851C-35)

4P03456-E7 (84XC-50,85XC-50)

EMC

EN1634:1 E90 4P01152 Fire

SFF3522-1093 Class 4/Class 5

EN14846 -X8E----- (850C,851C,840C,841C) 0402-CPR-SC0155-14 CE

EN14846 3 X 8 E 0 L 7 1 3 (850C,851C) SC0860-14 Performance

EN14846 3 X 8 E 0 L 5 1 3 (840C,841C) SC0173-15 Performance

EN 50130-4 4P03456-E6 (841C-35,851C-35)

4P03456-E7 (84XC-50,85XC-50)

EMC

EN1634:1 E90 4P01152 Fire

SFF3522-1093 Class 4/Class 5

Class 4 and Class5

To meet the Class 4 and Class 5, the following requirements must be met.

For Class 4 and Class 5 requires that the controller is installed in a protected space

with at least grade 3 locking. DAC564 controller must be installed in the SSF 3522

mode.

SSF 3522 Mode

To install a motor lock SSF 3522 mode you should do this:

1Initiate lock case.

2Turn off the power.

3Dip switch 3,7 & 8 in the On position.

4Turn on the power.

In 3522 the SSF mode will relay then have the following characteristics:

Relay ”Lock” Lock indicator, active for 15 seconds at locked.

Relay ”Alarm” Unlocked indication active for 60 seconds when unlocked.

Relay1 RC64 (Security locked) door closed and deadbolt out.

Relay2 RC64 (Unlocked) deadbolt inside.

Relay3 RC64 (Unlocked, with delay).

Relä4 RC64 (Closed Door).

Relä5 RC64 (Summer, Forced door).

RELAY6 RC64 (Tamper) Relay energized in alarm, the alarm must be installed.

Accessories SSF 3522

All components belonging to the locking device (such as lock cases, striking plates

and Door reinforcement) shall have the same classification according to SSF 3522.

25 (851-35) 48

Cylinder

∅10

5862,5

228(851-35)

225(841-35)

22 (841-35)

24177

200

17027,6

57 111

27,6

Drill for screw

4,0 x 25mm

225

25,5

20 M5 (2x)

25,5

Drill for screw

4,0 x 25mm

∅42∅42

R5 (4x) R5 (4x)

R5,5 (2x)

25 (851-35) 48

Cylinder

∅10

5862,5

228(851-35)

225(841-35)

22 (841-35)

24177

200

17027,6

57 111

27,6

Drill for screw

4,0 x 25mm

225

25,5

20 M5 (2x)

25,5

Drill for screw

4,0 x 25mm

∅42∅42

R5 (4x) R5 (4x)

R5,5 (2x)

25 (851-35) 48

Cylinder

∅10

5862,5

228(851-35)

225(841-35)

22 (841-35)

24177

200

17027,6

57 111

27,6

Drill for screw

4,0 x 25mm

225

25,5

20 M5 (2x)

25,5

Drill for screw

4,0 x 25mm

∅42∅42

R5 (4x) R5 (4x)

R5,5 (2x)

25 (851-35) 48

Cylinder

∅10

5862,5

228(851-35)

225(841-35)

22 (841-35)

24177

200

17027,6

57 111

27,6

Drill for screw

4,0 x 25mm

225

25,5

20 M5 (2x)

25,5

Drill for screw

4,0 x 25mm

∅42∅42

R5 (4x) R5 (4x)

R5,5 (2x)

Other manuals for 840C-50

This manual suits for next models

Table of contents

Other Assa Abloy Lock manuals

Assa Abloy

Assa Abloy hes RF0010 Owner's manual

Assa Abloy

Assa Abloy Zi IKON CLIQ Go User manual

Assa Abloy

Assa Abloy eCLIQ User manual

Assa Abloy

Assa Abloy Sargent IN100 User manual

Assa Abloy

Assa Abloy Access Control Electric Locking Manual

Assa Abloy

Assa Abloy Corbin Russwin IN100 Series User manual

Assa Abloy

Assa Abloy SARGENT Profile v.G1.5/LK User manual

Assa Abloy

Assa Abloy SECURITRON 32 Series User manual

Assa Abloy

Assa Abloy Corbin Russwin Access 600 CL33600 TCRNE1... User manual

Assa Abloy

Assa Abloy Corbin Russwin IN100 User manual

Assa Abloy

Assa Abloy Arrow AL-500 Series User manual

Assa Abloy

Assa Abloy Sargent 8200 Series User manual

Assa Abloy

Assa Abloy Yale 5300 Series User manual

Assa Abloy

Assa Abloy SARGENT FM7300 Series User manual

Assa Abloy

Assa Abloy OneSystem 509N Installation instructions

Assa Abloy

Assa Abloy Yale Real Living Assure Lock YRC216 Technical specifications

Assa Abloy

Assa Abloy Sargent Profile v.S1 User manual

Assa Abloy

Assa Abloy 3090 User manual

Assa Abloy

Assa Abloy ML53PA User manual

Assa Abloy

Assa Abloy RIXSON FM9930 User manual

Assa Abloy

Assa Abloy LOCKWOOD Sliding Door Latch User manual

Assa Abloy

Assa Abloy Yale Real Living B1L Z-Wave Technical specifications

Assa Abloy

Assa Abloy OneSystem 309N User manual

Assa Abloy

Assa Abloy Securitron Magnalock Series User manual

Popular Lock manuals by other brands

Magic

Magic 105 manual

Gantner

Gantner GAT NET.Lock 7020 System Installation, configuration & operation

Wittkopp

Wittkopp Insys 7202 manual

Dorma

Dorma Studio Classic Installation instruction

Securam

Securam ECSL-601 quick start guide

Sudhaus

Sudhaus 3003 operating manual

Safety 1st

Safety 1st 48517 user guide

Pado

Pado FDS-10 user manual

Esco

Esco systeQ Series installation instructions

COMPX

COMPX National D8951 instruction sheet

secureo

secureo Key Box instruction manual

Stock Loks

Stock Loks C8713 instruction sheet

COMPX

COMPX 1T-058 Information

Auslock

Auslock T11 user manual

ELCOM

ELCOM 7205 Operating instruction

Stealth SAFES

Stealth SAFES ShadowVault Instructions & Troubleshooting

Knox

Knox KeySecure 5 Admin & user guide

Kwikset

Kwikset 48334/01 Quick installation guide