Aruba 2930M Owner's manual
START HERE: Installation, Safety, and Regulatory
Information for the Aruba 2930M Switches
All product documentation
For the latest release of hardware and software documentation for your Aruba 2930M switch, visit the website at the
following link and use the search tool on the resulting destination page to locate the publications you want:
https://www.hpe.com/networking/ResourceFinder
•Aruba 2930M Switches Installation and Getting Started Guide
•START HERE: Installation, Safety, and Regulatory Information for the Aruba 2930M Switches (This document)
•ArubaOS-Switch Power Over Ethernet (PoE/PoE+) Planning and Implementation Guide
•ArubaOS-Switch and ArubaOS-CX Transceiver Guide
•Aruba 2930M and 3810M Switch Power Supply Quick Setup Guide and Safety/Regulatory Information
• All ArubaOS-switch operating system software manuals
See the remaining contents of this guide for important presetup information.
Applicable products
JL319A Aruba 2930M 24G 1-slot Switch JL325A Aruba 2930 2-port Stacking Module
JL320A Aruba 2930M 24G PoE+ 1-slot Switch JL078A Aruba 3810M/2930M 1-Port QSFP+ 40GbE Module
JL321A Aruba 2930M 48G 1-slot Switch JL081A Aruba 3810M/2930M 4 HPE Smart Rate 1G/
2.5G/5G/10G PoE+ Module
JL322A Aruba 2930M 48G PoE+ 1-slot Switch JL083A Aruba 3810M/2930M 4-Port 100M/1G/10G SFP+
MACsec Module
JL323A Aruba 2930M 40G 8 HPE Smart Rate PoE
+ 1-slot Switch
JL085A Aruba X371 12VDC 250W 100-240VAC Power
Supply
JL324A Aruba 2930M 24 HPE Smart Rate PoE+ 1-
slot Switch
JL086A Aruba X372 54VDC 680W 100-240VAC Power
Supply
R0M67A Aruba 2930M 40G 8 HPE Smart Rate PoE
Class 6 1-slot Switch
JL087A Aruba X372 54VDC 1050W 110-240VAC Power
Supply
R0M68A Aruba 2930M 24 HPE Smart Rate PoE Class
6 1-slot Switch
*5200-5204*
© Copyright , Hewlett Packard Enterprise Development LP
Part Number: 5200-5204
Published: June 2018
Edition: 1, Printed in Singapore
Installation precautions and guidelines
To help avoid personal injury or product damage when installing your switch, read the following installation precautions
and guidelines.
This section provides precautions and guidelines to observe when installing your switch. For full installation instructions,
see the Aruba 2930M Switches Installation and Getting Started Guide at http://h17007.www1.hpe.com/us/en/
networking/library/index.aspx?cat=switches&subcat=2930M&type=7. (Scroll to the Installation section and select the
latest version of the above-mentioned guide.)
WARNING:
• Do not mount the switch on a wall or under a table or under another horizontal surface.
• Mount devices installed in a rack or cabinet as low as possible. Put the heaviest devices at the bottom
and progressively lighter devices positioned higher.
• To prevent the rack or cabinet from becoming unstable and/or falling over, ensure that it is adequately
secured.
CAUTION:
• Do not ship any switch in a rack without checking for shipping restrictions in the Installation and Getting
Started Guide for your switch. Otherwise, you may void the switch warranty.
• Ensure that the power source circuits are properly grounded. Then connect the switch to the power
source by using the power cord supplied with the switch. For more information on power cords, see
Power cords on page 3.
• When installing the switch, ensure that the AC outlet is near the switch and easily accessible in case the
switch must be powered off.
• Ensure that the power cord and network cables at the switch mounting location do not create a tripping
hazard.
• Do not install the switch in an environment where the operating ambient temperature exceeds its
specification. (See the environmental operating temperature information in the Installation and Getting
Started Guide for your switch product. Visit http://www.hpe.com/networking/ResourceFinder and
locate the installation guide by using the search tool on the resulting destination page. )
• Ensure that the switch does not overload the power circuits, wiring, and over-current protection. To
determine the possibility of overloading the supply circuits, add the ampere ratings of all devices installed
on the same circuit as the switch. Then compare the total with the rating limit for the circuit. The maximum
ampere ratings for a device are usually printed near the device AC power connectors.
• Avoid blocking any ventilation openings on the sides, rear, or front of the switch.
• Ensure that the air flow around the switch is not restricted. Leave at least 3 inches (7.6 cm) for cooling.
For the air flow direction, see the Installation and Getting Started Guide for your product at http://
www.hpe.com/networking/ResourceFinder. (Locate the installation guide by using the search tool on
the resulting destination page.)
• If a power supply must be removed, and then reinstalled, wait at least 5 seconds before reinstallation.
Otherwise, damage to the switch may occur. The power supply needs this time to bleed off any retained
power.
• Install cover plates on any slot that is not in use.
Page 2
IMPORTANT:
• Use only supported Aruba SFP transceivers.
• The 2930M switch front panel transceiver slots support only SFP transceivers. To use SFP+ or QSFP+
transceivers with the switch, install an optional uplink module on the rear panel of the switch.
• For more information, visit http://www.hpe.com/networking/ResourceFinder and use the provided
search tool on the resulting destination page to locate the latest versions of these publications:
◦Aruba 2930M Installation and Getting Started Guide
◦ArubaOS-Switch and ArubaOS-CX Transceiver Guide
Power cords
Aruba includes the power cord intended for use with your Aruba switch. Different countries/regions may require different
power cords. For a list of the power cords that apply to your 2930M switch, see the section that lists power cords in the
latest edition of the Aruba 2930M Switch Series Installation and Getting Started Guide. To access this guide online:
1. Click http://h17007.www1.hpe.com/us/en/networking/library/index.aspx?cat=switches&subcat=2930M&type=7.
2. Scroll to the "Installation" section, where you will see a list of hardware installation documents.
3. Select the latest edition of the Aruba 2930M Switch Series Installation and Getting Started Guide.
CAUTION: Only Aruba-approved power cords may be used with Aruba devices. See the power cord
documentation provided in the latest version of the Aruba 2930M Switch Series Installation Guide at http://
h17007.www1.hpe.com/us/en/networking/library/index.aspx?cat=switches&subcat=2930M&type=7.
Lost or damaged power cords must be replaced only with Aruba-approved power cords. If your installation
requires a different power cord than the one supplied with the switch and/or power supply, use a power cord
that displays the mark of the safety agency that defines the regulations for power cords in your country or
region. The mark is your assurance that the power cord can be used safely with the switch and power supply.
WARNING: Do not use a damaged or nonrecommended power cord with your switch. Using such power
cords voids the switch and power supply warranty. It can also cause serious electrical problems, including
injury or death to personnel, and damage to the switch and other property. If you cannot verify that you have
a power cord approved for use with your switch model, contact your authorized Aruba dealer or sales
representative for assistance.
Aruba 2930M Switch Safety and Regulatory Information
NOTE: For important safety, environmental, and regulatory information, see Safety and Compliance
Information for Server, Storage, Power, Networking, and Rack Products, available at http://www.hpe.com/
support/Safety-Compliance-EnterpriseProducts.
Page 3
Table 1: Electrical information for 2930M switch power supplies
PoE+ Switches: JL320A, JL322A,
JL323A, JL324A, R0M67A, R0M68A
Non-PoE+ Switches: JL319A,
JL321A
Electrical
• AC voltage:
• Maximum current:
• Frequency range:
Per JL086A power supply:
• 100V-240V
• 8A- 3.5A
• 50 -60 Hz
Per JL085A power supply:
• 100 - 240 VAC
• 3A -1.2A
• 50 - 60 Hz
Per JL087A power supply:
• 110V-240V
• 12A- 5A
• 50 -60 Hz
Table 2: Safety and regulatory information for Aruba 2930M switch models
Safety-EU EN 60950-1:2006 +A11:2009 +A1:2010 +A12:2011+A2:2013
EN62368-1, Ed. 2
Safety- World Wide IEC60950-1:2005 Ed.2; Am 1:2009+A2:2013
IEC62368-1, Ed. 2
North American UL60950-1, CSA 22.2 No 60950-1
Lasers EN60825-1:2007 / IEC 60825-1: 2007 Class1
Class 1 Laser Products / Laser Klasse 1
EMC EN 55032:2012, Class A
EN 55024:2010
EN 61000-3-2:2014, Class A
EN 61000-3-3:2013
FCC CFR 47 Part 15:2010, Class A
RoHS EN 50581:2012
NOTE: Environmental and other switch specifications, such as acoustics data, are included in the Installation
and Getting Started Guide for your 2930M switch. To access the latest edition of this guide, visit https://
www.hpe.com/networking/ResourceFinder and use the search tool on the resulting destination page.
Table 3: Japan power cord warning
Japan Power Cord
Warning
Page 4
Table 4: China Altitude Warning
China Altitude Warning
Power supply instructions
WARNING: During the installation, ensure that AC power is NOT connected to the Power Supply.
CAUTION: Shock hazard
To completely remove power from the switch, disconnect all
power cords.
For more information, see the Power over Ethernet (PoE/PoE+) Planning and Implementation Guide. To access this
guide, visit http://www.hpe.com/networking/ResourceFinder and use the search tool on the resulting destination page
to locate the guide.
Interior Wiring
Warning
Brazil Statement Este equipamento deve ser conectado obrigatoriamente em tomada de rede de energia
elétrica que possua aterramento (três pinos), conforme a Norma NBR ABNT 5410, visando a
segurança dos usuários contra choques elétricos.)
Battery Statements:
IMPORTANT: The only indicator of battery failure is the failure of the switch internal clock to keep the correct
time across a reboot or power cycle. If a battery failure occurs, contact your authorized Aruba representative
for assistance. Batteries are not customer-serviceable and battery failures should be referred only to service
personnel authorized by Aruba.
For important safety, environmental, and regulatory information, see Safety and Compliance Information for
Server, Storage, Power, Networking, and Rack Products, available at
http://www.hpe.com/support/Safety-Compliance-EnterpriseProducts
ATTENTION ll y a danger d'explosion s'il y a remplacement incorrect de la batterie.
Remplacer uniquement avec une batterie du même type ou d'un type équivalent recommandé
par le constructeur.Mettre au rebut les batteries usagées conformément aux instructions du
fabricant.
Page 5
ATTENTION The battery supplied with this product may contain perchlorate material. Special handling may
apply in California and certain other states. See http://www.dtsc.ca.gov/hazardouswaste/
perchlorate Web site for more information.
CAUTION: A risk of explosion exists if a battery is replaced by an incorrect type. Dispose of used batteries
according to the instructions.
Japan VCCI Class A
Korea EMC Class A Statement
European Community
The product herewith complies with the requirements of Directive 2014/35/EU relating to electrical equipment designed for
use within certain voltage limits, Directive 2014/30/EU relating to electromagnetic compatibility, Directive 2011/65/EU on
the restriction of the use of certain hazardous substances in electrical and electronic equipment and carries the CE
marking accordingly.
NOTE: For Conducted and Radiated Immunity in accordance with EN55024, the Aruba 2930M switch
products are limited to Performance Criteria A with shielded cable for HPE Smart Rate ports.
Belarus Kazakhstan Russia marking
For manufacturer and local representative information, see Safety and Compliance Information for Server, Storage,
Power, Networking, and Rack Products at http://www.hpe.com/support/Safety-Compliance-EnterpriseProducts.
Preview of installing a 2930M switch
IMPORTANT: This section previews the steps for installing the switch. To find detailed switch installation
steps, information on configuration tools, and other instructions and information, see the Aruba 2930M
Switches Installation and Getting Started Guide. (Visit https://www.hpe.com/networking/ResourceFinder
and use the search tool on the resulting destination page.)
Page 6
1. Prepare the installation site.
2. Unpack the switch and verify that you have received the correct parts.
3. Connect power to the switch and observe the switch self-test. then remove power from the switch.
4. Mount the switch.
WARNING: Do not mount the switch on a wall, under a table, or under another horizontal surface.
5. Connect the switch to a power source.
6. Connect the network cables.
7. (Optional) Install SFP transceivers.
8. Configure the switch for network operation.
For related publications, see All product documentation on page 1.
Documentation feedback
To help improve Aruba documentation, please send documentation suggestions, comments, and notice of any errors to
Documentation Feedback ([email protected]). When submitting your feedback, include the document title, part
number, edition, and publication date located on the front cover of the document. For online help content, include the
product name, product version, help edition, and publication date located on the legal notices page.
Page 7
Other manuals for 2930M
1
Table of contents
Other Aruba Switch manuals
Aruba
Aruba S3500-24P User manual
Aruba
Aruba 3810M User manual
Aruba
Aruba 2530 User manual
Aruba
Aruba S1500 Series User manual
Aruba
Aruba Instant On 1930 Series User manual
Aruba
Aruba 6400 Series User manual
Aruba
Aruba 8400 Series User manual
Aruba
Aruba 6400 Series Owner's manual
Aruba
Aruba JL320A User manual
Aruba
Aruba JL253A User manual
Aruba
Aruba 8325 Series User manual
Aruba
Aruba 8360 Series User manual
Aruba
Aruba 6300F Series User manual
Aruba
Aruba Instant On 1930 Series Owner's manual
Aruba
Aruba Instant On 1430 User manual
Aruba
Aruba 8320 User manual
Aruba
Aruba 2540 User manual
Aruba
Aruba 4100i Series User manual
Aruba
Aruba 8360 Series User manual
Aruba
Aruba 2930F Series Owner's manual
