Artis BE810M User manual
U S E R M A N U A L
BE810M
BT Earbuds
Music & Calls Wirefree!
• Please properly control the volume and time when using the headset.
• To ensure the safety, please do not use the headset in a potentially
dangerous environment.
• Try to avoid listening to music, making or answering a call while driving,
because the distraction may lead to danger.
• Please keep the headset away from children, to avoid danger due to
improper use by them.
• Avoid water from entering the headset during grooming, to avoid damage
of the headset or sound quality.
• Try to avoid turning the volume so high that you cannot hear anything
around you. please adjust to an appropriate volume if you have tinnitus or
the volume is too high.
• Please immediately stop using the headset when feeling obvious
discomfort, irritation or other adverse reactions during using it.
• Avoid storing or using the headset in an environment with temperature
lower than -15°C (5°F ) or higher than 55°C (131°F); otherwise, this may
shorten the life of headset or battery.
Attention Notice :
Earphone Overview:
Headset use :
Insert the headset into
the ear as shown
Rotate the headset to apply
it to the ear canal.
Charging and Battery:
1. Please turn off the headset before charging.
2. Insert the USB charging cable into the Micro USB charging interface of the
charging case, with the other USB end into a USB charger or other charging
device. And the charging case will start to be charged, with the red light
normally on during the charging. The red light will disappear when the case is
fully charged.
3. Put the left and right headsets into the charging case, close the upper cover of
the charging case, press the switch at the bottom of the charging case, and the
headsets in the charging case will show red light. About 2h later, at full charge,
the red light will be off and blue light will be normally on.
Warning:
These headsets and charging case use the built-in rechargeable battery that is
non-removable. Do not attempt to remove the battery from the headset and
charging case, otherwise, it may damage them.
• BT transmission range can reach above 10m when there is no barrier or
interference (the range may be slightly varied for different mobile phones)
• Receiving sensitivity: -85dBm
• Battery capacity: 50mAh for both left and right headsets
• Charging: the special charging case is equipped, which has 300mAh battery
capacity.
• After the headsets are fully charged, the time for listening to music or making
calls with single headset is 5h and with both headsets is 2.5h (the use time
may be slightly varied depending on the volume and device).
• Standby time: when using single headset: 120h, when using both headsets: 60h
• The headsets will show red light when being charged in the charging case, and
will show blue light at full charge. The headsets are neither being charged nor
discharging at full charge.
• Charging time: About 1-2h for both headsets to be fully charged
• It takes about 2h for the charging case to be fully charged, with red light as
charging indicator
• The mobile phone will display the headset battery status and the headset will
show the blue discharging indicator light, after the headset is successfully
connected to the mobile phone
• Using CVC6.0 noise cancelling technology
• Caller ID reporting and voice prompt supported
• Support: a2dp\avctp\avdtp\avrcp\hfp\spp\smp\
att\gap\gatt\rfcomm\sdp\12cap profile
1. Separately Using the Left and Right Headsets Turning On:
• Long press the Multifunction key until the blue light is on and the headset
makes an audio prompt.
How To Pair The Earphone:
Website: www.artis.in | www.artisstore.com
Customer care: +91-20-26113250/60
Email: supportpune@artis.in
Headset
charging pin
Headset charging indicator
USB charging
interface
Headset charging switch
Microphone
Indicator
Multi functional Key
charging indicator
Headset charging
contact point
• Long press the Multifunction key until the red light and blue light blink in turn,
and the headset will make an audio prompt.
• Please keep the distance between the BT headset and a mobile
phone (or other devices to connect) within 1m, the closer, the better.
• Turn on the headset, and confirm that it has entered the pairing mode with the
red light and blue light blinking in turn.
• Enable the BT search function of the mobile phone or other devices to
connect, and the mobile phone will display "TWS Ear buds" Found.
• Select "TWS Ear buds" (For some mobile phones, you need entering "0000" as
the pairing password), and the BT headset will automatically connect
with the mobile phone, with the blue light blinking.
Pairing Mode:
• Long press the Multifunction key until the red light is on and then off, and the
headset will make an audio prompt.
2. Using the Left and Right Headsets at the Same Time.
Turning Off:
• Long press the right headset key to turn it on, until the LED red light changes to
red and blue light blinking at the same time (now, the right headset will be the
main headset as it was first turned on, and the left headset will be the auxiliary
headset as it was turned on later than the right headset, and vice versa).
• Press the left headset key to turn it on, until the LED shows red light, and now
the left headset will automatically connect to the right headset, and the red
light of the left headset will change to blue light after successful connection.
• Turn on the mobile phone BT, search BT headset named "TWS Ear buds" , and
touch the name to establish connection. The "Connected" word will show
behind the BT headset name and the mobile phone screen will show the
headset battery status if the connection is established. Now, the LED light on
both headsets will blink blue light at the same time, meaning both headsets are
successfully connected to the mobile phone.
BT Pairing Steps:
• You can listen to music in the mobile phone music library after the successful
connection. The headset volume needs to be adjusted via the mobile phone
(the headset blue LED light will blink once every 5s).
Attention:
• The maximum pairing time of the BT headset is 120s. If the light is off, it means
that the BT pairing status has stopped, and if you still fail to pair them, please
repeat the above steps to pair them again, or delete the previous connection
name on your phone (if have), try the other side to be the main headset.
Operation Instructions:
• To disconnect the headset and mobile phone BT, please use any one of the
following methods:
• Turn off the mobile phone BT
• Long press the headset Multifunction key until the red light is off, and the
• headset will automatically power off.
• Move the headset to a place 20m (about 60 feet) or farther away from the
mobile phone.
Reconnect the paired headset and mobile phone:
1. Please keep the distance between the BT headset and the mobile phone (or
other devices to connect) within lm, the closer, the better.
2. Turn on the headset, and it will enter the reconnecting mode with the blue light
blinking.
3. Enable the BT search function of the mobile phone or other devices to connect,
and the BT headset will automatically reconnect to the mobile phone
connected last time.
6. Can the headset be used to control App's on the mobile phone after the
headset and mobile phone are connected?
A: The device APP settings may be varied, which makes functions of some
App's uncontrollable by the headset
Answering a Call:
• Press the Multifunction key to answer it when there is a call and you hear the
sound prompt made by the headset, or answer it with your mobile phone.
• If the above problems happen to the product: delete the paired BT
device on the mobile phone, turn off the left and right headsets, and then turn
on both headsets at the same time by long pressing them for above 8s; both
headsets will search and pair with each other (with red light and blue light
blinking in turn), and LED lights of both headsets will change to blue
after having searched each other, meaning successfully pairing with each
other; then you can pair the BT according to the above steps.
If the headset BT fails to successfully connect to the mobile phone BT, the
reasons may be;
1. The product was not successfully paired in the factory: if one headset shows
red and blue light and the other shows red light after they are normally turned
on, both headsets will not be successfully connected to the mobile phone
BT.
2. In the case that the product was paired successfully in the factory: pairing of
the two headsets may be disconnected due to operation mistake of the user
Both headsets will also not be successfully connected to the mobile phone if
they both show red light.
Special Tips:
Rejecting a Call:
• Continuously press the Multifunction key for twice to reject it when there is a
call and you hear the sound prompt made by the headset or reject it with your
mobile phone.
Hanging Up:
• Press the headset Multifunction key to hang up during a conversation, or hang
up with the mobile phone hang-up button.
Music / Music playback:
• Press the Multifunction key to play or pause the music.
Continuously press the Multifunction key twice to switch to next track.
Prompting Language
• Default: English
FAQ’s:
1. BE810M Headset cannot be turned on.
A: Please check the battery status of the headset.
2. Can the battery of BE810M Headset be replaced?
A: No. The headset uses the lithium polymer battery that is non-removable.
3. Can BE810M Headset be used while driving?
A: The communication Ear Buds can be used while driving, but it is not
recommended to use the headsets while driving.
4. BE810M headset disconnects with the mobile phone within 10m.
A: Please check if there is any metal or other object within the connection
range that affects the connection, as BT is a wireless technology that is
sensitive to the objects between the headset and the connected device.
5. No sound is heard after the headset is connected to a computer or mobile
phone.
A: Please check if the computer output channel has been set to BT audio device
and if the computer BT supports A2DP; also check the volume of the
computer/mobile phone.
• Real wireless stereo, left and right channels separated, HIFI quality
• Both the left and right headsets possess complete BT headset functions, and
can be used alone or in pair.
• Compliant with BT V4.2+BR+EDR+BLE specification
• BT frequency range: 2.4GHZ
Technical Specifications:
Other Artis Headphones manuals
