Argox AS-8312 User manual

NOTICE:

This equipment has been tested and it complies with

the limits for a Class a digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to

provide a reasonable protection against harmful

interference when the equipment is operated under a

commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the

instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in

a residential area is likely to cause harmful

interference in which case the user will be required to

correct the interference at his own expenses.

Note: All brands and trademarks shall belong to their

respective owner.

Note: Specification is subject to changes without

notice.

This device complies with Part 15 of the FCC Rules.

Operation shall be subject to the following two

conditions:

(1) This device may not cause harmful interface, and

(2) This device must accept any interface received,

including interface that may cause undesirable

operation.

Introduction

Installation- Keyboard Wedge

1) First of all, you must switch off power for the

terminal/computer.

2) Disconnect the keyboard cable from the back of the

terminal/computer.

3) Connect the appropriate interface cable to the scanner

and to the terminal/computer.

4) Turn the terminal/computer power on.

RS-232

1) Disconnect power to the terminal/computer.

2) Connect the appropriate interface cable and external

power supply (DC adapter) to the scanner.

3) Plug the serial connector into the serial port on the back

of your computer/terminal. Tighten the two screws to

secure the connector to the port.

4) Plug the power pack into power source.

5) Once the scanner has been fully connected, turn the

terminal/computer power back on.

USB (Simulate with keyboard wedge)

1) Connect the USB cable between scanner and PC.

2) Windows will automatically detect the USB device.

Note: If any of the above operation is incorrect, turn off the

power immediately and check any improper

connections. Go through all above steps again.

Default setting

For each barcode shown as below:

Code Type

Read

Enable

Checksum

Verification

Enable

Checksum

Transmission

Enable

Code

8110 / 8120

UPC-A

UPC-E

EAN-13

EAN-8

Code-39

＊

Interleaved

2 of 5

Industrial

2 of 5

Matrix 2 of 5

Codabar

V (8110)

Code-128

Code-93

V two digits

Code-11

VOne digit

MSI/Plessey

UK/Plessey

Telepen

Standard 2 of 5

RSS-14

RSS-Limited

RSS-Expanded

China Post

Italian

Pharmacode.

Code Type

Read

Enable

Checksum

Verification

Enable

Checksum

Transmission

Enable

Code

8150

8250

8310

8312

UPC-A

UPC-E

EAN-13

EAN-8

Code-39

＊

Interleaved

2 of 5

Industrial

2 of 5

Matrix 2 of 5

Codabar

Code-128/

GS1-128

Code-93

V two digits

Code-11

VOne digit

MSI/Plessey

UK/Plessey

Telepen

Standard 2 of 5

China Post

Italian

Pharmacode.

Code-16K

PDF417

EAN UCC

Composite

RSS-14

RSS-Limited

RSS-Expanded

Micro-PDF

8312

only

Weight

155 g

120 g

ArgoScan 8110 / 8120

Specification

Model 8110

Model 8120

Operational

Light Source

660 nm Visible Red LED

Optical System

2048 pixel CCD

(Charge-coupled device)

Depth of Scan Field

0-80 mm

(CODE 39,

PCS=90%, 20mils)

0-150 mm

(code 39,

PCS=90%, 20mils)

Scanning Width

80 mm at contact

75mm at contact

Scan Speed

50 scans/sec

100 scans/sec

Resolution

4mils, Code39, PCS=90%, on contact

5mils, Code39, PCS=45%, on contact

Print Contrast

30% or more

Scanning Angle

Pitch: 60° Skew: 75°

Decode Capability

Auto-discriminates all standard

barcodes; Other symbologies can be

ordered optionally

Beeper Operation

7 tones or no beep

Indicator

Green led

Blue led

Mechanical

Length

182 mm

Width-handle

26 mm

Width-head

90 mm

Depth-handle

51 mm

49mm

Depth-head

35 mm

Cable –K/B wedge

Straight 2.0 m

Cable –universal

type

Straight 2.3 m

Connector type

RJ-45 phone jack connector

Case material

ABS

Cushion material

Rubber

Electrical

Input Voltage

5 VDC ± 0.25V

Power - Operating

380 mW

850mW

Power - Standby

240 mW

250 mW

Current - Operating

76 mA @ 5 VDC

170 mA@5 VDC

Current - Standby

48 mA @ 5 VDC

50 mA@5 VDC

DC Transformers

Class 2; 5VDC @ 450 mA

Agency listing

FCC Class A,CE, BSMI

Environmental

Operating

Temperature

0℃to 45℃(32℉to 113℉)

Storage

-20℃to 60℃

(-4℉to 140℉)

Humidity

5% to 90% relative humidity,

non-condensing

Light Level

Up to 15000 Lux.

Up to 20000 Lux.

Shock

1.0m

1.2m

Contaminants

Seals to resist airborne particulate

contaminants

Ventilation

None required

Programming

method

Manual (Reading special barcode) DOS

command through RS-232, Windows

configuration program (8110)

Program upgrade

Enabled built-in flash memory (8110)

Programmable

characteristics

Code type selection, check digit

selection Decoding option Decoding

option Transmitted character delay,

Header selection, trailer selection,

message suffix, good read beep tone

and volume, scanner trigger selection

Keyboard emulation type

(intermessage delay, keyboard type

and keyboard language)

Serial interface type (ACK/NAK,

Xon/Xoff, RTS/CTS, good read LED

control, start/stop bits)

ArgoScan 8150 / 8250 / 8310 / 8312

Specification

Model

8150/8250

Model

8310/8312

Operational

Light Source

660 nm Visible Red

LED

630 nm Visible Red

LED

Optical System

2048 pixel CCD

(Charge-coupled device)

Depth of Scan Field

0-250 mm

(CODE 39,

PCS=90%, 20mils)

Up to 600mm

(CODE 39,

PSC=90%, 20mils)

Scanning Width

120 mm

160mm

Scan Speed

200 scans/sec

450 scans/sec

Resolution

0.1mm(4mils);

Code39,PCS=90%,

on contact (8150);

Code39,PCS=45%,

on contact (8250)

0.1mm(4mils)

Code39,PCS=90%

Print Contrast

25% or more

Scanning Angle

Front: 60° Rear: 60° Yaw: 75°

Decode Capability

Auto-discriminates all standard

barcodes; Other symbologies can be

ordered optionally (2D symbologies for

8250 and 8312 only)

Beeper Operation

7 tones or no beep

Indicator

Green led

Green & Red led

Mechanical

Length

182 mm

164 mm

Depth-head

35 mm

Weight

150 g (cable not

included)

176 g (cable not

included)

Cable –K/B wedge

Straight 2.0 m

Coiled 2.5 m

Cable –universal

type

Straight 2.3 m

Coiled 2.5 m

Cable- USB

Straight 2.0 m

Coiled 2.5 m

Connector type

RJ-45 phone jack connector

Case material

ABS plastic

ABS (over molded

at contact pointed)

Cushion material

Rubber

Double injection

Electrical

Input Voltage

5 VDC ± 0.25V

Power - Operating

1275 mW

800 mW

Power - Standby

600 mW

350 mW

Current - Operating

255 mA (8150);

180 mA (8250)

@ 5 VDC

160 mA @ 5 VDC

Current - Standby

120 mA (8150);

100 mA (8250)

@ 5 VDC

70 mA @ 5 VDC

DC Transformers

Class 2; 5VDC @ 450 mA

Agency listing

UL, FCC Class A,

UL, FCC Class B,

Environmental

Width-handle

26 mm

30 mm

Width-head

74 mm

78 mm

Depth-handle

51 mm

56 mm

Operating

Temperature

0℃to 45℃

(32℉to 113℉)

0℃to 45℃

(32℉to 113℉)

Storage

-40℃to 60℃

(-40℉to 140℉)

-20℃to 60℃

(-4℉to 140℉)

Humidity

5% to 90% relative humidity,

non-condensing

Light Level

Up to 60000 (8150);

80000 (8250) Lux.

Up to 70000 Lux.

Shock

1.5m drop onto concrete

Contaminants

Seals to resist airborne particulate

contaminants (IP42)

Ventilation

None required

Programming

method

Manual (Reading special barcode) DOS

command through RS-232, Windows

configuration program

Program upgrade

Enabled by built-in flash memory

Programmable

characteristics

Code type selection, check digit

selection Decoding option Decoding

option Transmitted character delay,

Header selection, trailer selection,

message suffix, good read beep tone

and volume, scanner trigger selection

Keyboard emulation type

(intermessage delay, keyboard type

and keyboard language)

Serial interface type (ACK/NAK,

Xon/Xoff, RTS/CTS, good read LED

control, start/stop bits)

Table of contents

Argox AS-8312 User manual

Popular Barcode Reader manuals by other brands