Frameless Fixing Kit
Frameless Fixing KitFrameless Fixing Kit
Frameless Fixing Kit
Installation Guide
Installation GuideInstallation Guide
Installation Guide
Thank you for purchasing an AQUAVISION
Thank you for purchasing an AQUAVISIONThank you for purchasing an AQUAVISION
Thank you for purchasing an AQUAVISION
®
®®
®
Television
TelevisionTelevision
Television
.
..
.
Safety
SafetySafety
Safety
AQUAVISION
®
recommends installation to e carried out y a qualified installer. Please ensure that the latest wiring and safety regulations
are adhered. If your AQUAVISION
®
is powered y a low voltage (24v DC) power supply unit. This should e positioned away from any
water source. Please o serve the safety zones in athrooms and other wet areas. IF IN DOUBT REFER TO A QUALIFIED PERSON.
IF IN DOUBT REFER TO A QUALIFIED PERSON. IF IN DOUBT REFER TO A QUALIFIED PERSON.
IF IN DOUBT REFER TO A QUALIFIED PERSON. THE
THE THE
THE
FRONT AND BACK PART
FRONT AND BACK PARTFRONT AND BACK PART
FRONT AND BACK PARTS OF
S OF S OF
S OF THIS APPLIANCE MUST BE EARTHED
THIS APPLIANCE MUST BE EARTHEDTHIS APPLIANCE MUST BE EARTHED
THIS APPLIANCE MUST BE EARTHED
Positioning
PositioningPositioning
Positioning
Each AQUAVISION
®
model has specific viewing angles as shown on the ta le Fig 3. Position the front panel in order to view the picture
clearly from all intended areas. Should there e any dou t, make the area safe and power up the LCD, positioning the screen until satisfied
that the picture does not darken or disappear from view.
Wall
Wall Wall
Wall M
MM
Mounting and
ounting and ounting and
ounting and C
CC
Ca le
a le a le
a le F
FF
Feed
eedeed
eed
When the position has een defined, cut a hole in the wall to the cut-out dimensions specified for your AQUAVISION
®
model (Fig. 2).
Sink the ack ox into this hole to ensure that it fits. Remove the ox until the finish has een applied to the walls. This could e tiles, plaster,
paint, paper etc.
Run the ca les to their positions as shown in Fig. 1, ensuring that there is enough ca le slack to connect to the rear of the AQUAVISION
®
unit. Ensure that the ca les are easily availa le and cannot fall ack into the cavity, etc.
Final
Final Final
Final Fix
FixFix
Fix
Once the wall is finished, apply a ead of silicon all around the ack of the flanges on the ack ox. Carefully sink this ack ox into the hole
that you checked earlier ensuring that the silicone gives a good waterproof seal against the tiles and fasten securely eing careful not to distort
the ox when tightening the fixings.. You must take care not to end or damage the outer flanges of the ox as this could potentially hinder
any water-proofing qualities and thus void any guarantee. Note it is not advisa le to use raised order tiles under the edge of the ezel frame.
and (See Fig. 3 or 4). This prevents moisture from accessing the sides of the front panel. The ack ox is now in position to accommodate
the LCD unit and finally the front glass panel. Instructions on fitting these components are supplied with each item respectively.
CABLING SCHEMATIC
CABLING SCHEMATICCABLING SCHEMATIC
CABLING SCHEMATIC
B
BB
BACK BOX
ACK BOXACK BOX
ACK BOX
SIZES AND CUTOUTS
SIZES AND CUTOUTSSIZES AND CUTOUTS
SIZES AND CUTOUTS
Fig 1
Fig 1Fig 1
Fig 1
Fig 2
Fig 2Fig 2
Fig 2
INSTALLATION
INSTALLATION INSTALLATION
INSTALLATION S
SS
SCHEMATIC
CHEMATICCHEMATIC
CHEMATIC
ASSEMBLY
ASSEMBLYASSEMBLY
ASSEMBLY
S
SS
SCHEMATIC
CHEMATICCHEMATIC
CHEMATIC
Fig 3
Fig 3Fig 3
Fig 3
Fig 4
Fig 4Fig 4
Fig 4
The specifications shown were accurate at time of going to press. AQUAVISION
AQUAVISIONAQUAVISION
AQUAVISION’S
SS
S
®
policy of continuous development means some changes may take place.
Please check with the office for confirmation. All screen pictures simulated. E. & O.E.
REV 4.0.2
Model
ModelModel
Model
Screen
ScreenScreen
Screen
Size
SizeSize
Size
