APsystems YC600 User manual
How To Troubleshoot an Inoperable APsystems
Microinverter
A flashing red LED indicates the AC grid is either not present or not within specification.
The microinverter does not sense that the utility grid is within voltage/frequency
specifications, and cannot produce power until this is resolved. To troubleshoot an
inoperable APsystems microinverter, follow the steps in the order shown to diagnose
your solar system.
* WARNING: Risk of electric shock. Always de-energize the AC branch circuit before
servicing. Never disconnect the DC connectors under load.
* WARNING: The APsystems Microinverters are powered by DC power from the PV
modules. Make sure you disconnect the DC connections and reconnect DC power and
then watch for three green blinks after connection to DC power.
Troubleshooting an APsystems System - 15 Steps:
1. Make sure AC breakers and disconnects are closed (off).
2. Check the connection to the utility grid and verify that the utility voltage is within
allowable ranges.
3. Verify that AC line voltages at all solar power circuit breakers at the load center and
sub-panels are within the ranges shown in the following table.
4. Verify that AC line voltage at the junction box for each AC branch circuit is within the
ranges shown in the following table:
240 Volt AC, Single Phase or
Three Phase
208 Volt AC, Three Phase
L1 to L2
211 to 264 VAC
L1 to L2 to L3
183 to 229 VAC
L1, L2 to
neutral
106 to 132 VAC
L1, L2, L3 to
neutral
106 to 132 VAC
5. Using an APsystems disconnect tool, disconnect the AC cable for the microinverter in
question from the trunk cable.
6. Verify that utility power is present at the microinverter by measuring line to line and
line to neutral at the trunk cable connector.
7. Visually check that the AC branch circuit connections (trunk cable and AC
connections) are properly seated. Reseat if necessary. Check also for damage, such as
rodent damage.
8. Make sure that any upstream AC disconnects, as well as the dedicated circuit
breakers for each AC branch circuit, are functioning properly and are closed.
9. Disconnect and reconnect the DC PV module connectors. The Status LED of each
microinverter will light solid green three times in a few seconds after connection to DC
power and then blink green every ten seconds indicate normal start-up operation about
five minutes after connecting to DC power. The LED subsequently resumes normal
operation if the grid is present. See page 15 of the Installation and Operation Manual
for normal LED operation. (YC600/QS1)
10. Clamp onto one of the DC cables with a multimeter from the PV module to measure
micro inverter current. This will be under one Amp if AC is disconnected.
11. Verify the PV module DC voltage and current is within the allowable range shown in
“Specifications” on page 20 of the manual. (YC600/QS1)
12. Swap DC leads with a known good, adjacent PV module. If after checking the EMA
periodically (this may take up to 30 minutes), the problem moves to the adjacent
module, this indicates that the PV module isn’t functioning correctly. If it stays in place,
the problem is with the microinverter. Call APsystems Technical Support for help in
reading the microinverter data and for help in obtaining a replacement microinverter, if
needed.
13. Check the DC connections between the microinverter and the PV module. The
connection may need to be tightened or reseated. If the connection is worn or damaged,
it may need replacement.
14. Verify with your utility that line frequency is within range (some multimeters have a
frequency function to check this easily)
15. If the problem persists, please email directly to this response. Please do not reply to
auto-generated emails or emailing [email protected]; not emailing this
email directly can cause your request to take longer to resolve with the possibility of lost
information. Thank you.
Other manuals for YC600
4
This manual suits for next models
1
Table of contents
Other APsystems Inverter manuals
APsystems
APsystems YC1000-3-208 Instruction Manual
APsystems
APsystems YC500 Guide
APsystems
APsystems QT2 User manual
APsystems
APsystems YC600 User manual
APsystems
APsystems YC1000-3-NA User manual
APsystems
APsystems YC500i Series Instruction Manual
APsystems
APsystems DS3-M User manual
APsystems
APsystems DS3 Series User manual
APsystems
APsystems YC1000-3 3-Phase Instruction Manual
APsystems
APsystems DS3D User manual
APsystems
APsystems QT2 User manual
APsystems
APsystems QS1 User manual
APsystems
APsystems QT2-220 User manual
APsystems
APsystems QS1-LK User manual
APsystems
APsystems EZ1 Series User manual
APsystems
APsystems QT2-AU User manual
APsystems
APsystems QT2D User manual
APsystems
APsystems YC1000-3-220 User manual
APsystems
APsystems YC600 Instruction Manual
APsystems
APsystems QT2 User manual
