AOC 46D9115 User manual
www.aoc.com
©2019 AOC. All Rights Reserved.
User Manual
46D9115
55D9115
Please read this manual before use and retain it for future reference.
ii
Safety Instructions
Safety precautions and maintenance
WARNING: Use of controls, adjustments or procedures other than those specied in this documentation
may result in exposure to shock, electrical hazards and/or mechanical hazards.
Read and follow these instructions when connecting and using your display:
Operation:
• Keep the display out of direct sunlight and away from stoves or any other heat sources.
• Remove any object that could fall into ventilation holes or prevent proper cooling of the display’s electronics.
• Do not block the ventilation holes on the body ofVibe.
• When positioning the display, make sure the power plug and outlet are easily accessible.
• When turning off the display by detaching the power cord, wait 6 seconds before re-attaching the power cord for
normal operation.
• Ensure the use of an approved power cord at all times. If your power cord is missing, please contact your local
service center.
• Do not subject the display to strong vibration or high impact during operation.
• Avoid Dropping the display during operation or transportation.
Maintenance:
• To protect your display from possible damage, do not put excessive pressure on the LCD panel.When moving your
display, hold the frame to lift; do not lift the display by placing your hand or ngers on the LCD panel.
• Unplug the display if you are not going to use it for an extensive period of time.
• Unplug the display if you need to clean it with a slightly damp cloth.The screen may be wiped with a dry cloth
when the power is off. However, never use organic solvent, such as, alcohol, or ammonia-based liquids to clean your
display.
• To avoid the risk of shock or permanent damage to the hardware, do not expose the display to dust, rain, water or
an excessively moist environment.
• If your display becomes wet, wipe it with dry cloth as soon as possible.
• If a foreign substance or water gets in your display, turn the power off immediately and disconnect the power cord.
Then remove the foreign substance or water, and send the unit to the maintenance center.
• Do not store or use the display in locations exposed to heat, direct sunlight or extreme cold.
• In order to maintain the best performance of your display and ensure a longer lifetime, we strongly recommend
using the display in a location within the following temperature and humidity ranges.
-Temperature: 0-40°C 32-104°F
-Humidity: 20-80% RH
IMPORTANT: Always activate a moving screen saver program when you leave your display unattended. Always activate
a periodic screen refresh application if the unit will display unchanging static content. Uninterrupted display of still or
static images over an extended period may cause “burn in”, also known as “after-imaging” or “ghost imaging”, on your
screen.This is a well-known phenomenon in LCD panel technology. In most cases, the “burned in” or “after-imaging” or
“ghost imaging” will disappear gradually over a period of time after the power has been switched off.
WARNING: Severe “burn-in” or “after-image” or “ghost image” symptoms will not disappear and cannot be repaired.
This is also not covered under the terms of your warranty.
iii
Service:
• The casing cover should be opened only by qualied service personnel.
• If there is any need for repair or integration, please contact your local service center.
If your display does not operate normally, having followed the instructions in this document, please
contact a technician or your local service center.
Read and follow these instructions when connecting and using your display:
• Consult a service technician if the display does not operate normally when you have followed the
instructions in this manual.
• The back cover should be opened only by qualied service personnel.
• Keep the display out of direct sunlight and away from stoves or any other heat sources.
• Remove any object that could fall into the vents or prevent proper cooling of the display’s electronics.
• Do not block the ventilation holes on the cabinet.
• Keep the display dry.To avoid electric shock, do not expose it to rain or excessive moisture.
• When turning off the display by detaching the power cable or DC power cord, wait for 6 seconds
before re-attaching the power cable or DC power cord for normal operation.
• To avoid the risk of shock or permanent damage to the set do not expose the display to rain or
excessive moisture.
• When positioning the display, make sure the power plug and outlet are easily accessible.
• This product’s power cord is equipped with a three-wire grounded plug. The plug only ts in a
grounded power outlet. Make sure the power outlet is properly grounded before inserting the power
cord plug. Do not insert the plug into a non-grounded power outlet. Contact your electrician for
details.
• IMPORTANT: Always activate a screen saver program during your application. If a still image in
high contrast remains on the screen for an extended period of time, it may leave an ‘after-image’ or
‘ghost image’ on the front of the screen.This is a well-known phenomenon that is caused by the
shortcomings inherent in LCD technology. In most cases the afterimage will disappear gradually over a
period of time after the power has been switched off. Be aware that the after-image symptom cannot
be repaired and is not covered under warranty.
iv
Federal Communications Commission (FCC) Notice (U.S. Only)
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
Changes or modications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Use only an RF shielded cable that was supplied with the display when connecting this display to a computer device.
To prevent damage which may result in re or shock hazard, do not expose this appliance to rain or excessive moisture.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
End-of-Life Disposal
Your new Public Information Display contains materials that can be recycled and reused. Specialized companies can
recycle your product to increase the amount of reusable materials and to minimize the amount to be disposed of.
Please nd out about the local regulations on how to dispose of your old display from your local dealer.
(For customers in Canada and U.S.A.)
This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations. For
additional information on recycling contact www.eia.org (Consumer Education Initiative)
Waste Electrical and Electronic Equipment-WEEE
Attention users in United States:
Please dispose of according to all Local, State and Federal Laws. For the disposal or recycling information, contact: www.
mygreenelectronics.com or www.eiae.org.
End of Life Directives-Recycling
Your new Public Information Display contains several materials that can be recycled for new users.
Please dispose of according to all Local, State, and Federal laws.
v
Table Of Contents
1. Unpacking and Installation.....................................................................................................1
1.1. Unpacking .....................................................................................................................................................1
1.2. Package Contents.....................................................................................................................................1
1.3. Installation Notes......................................................................................................................................1
1.4. Operating Instructions of wall mount brackets ......................................................................2
2. Parts and Functions.................................................................................................................4
2.1. Input/Output...............................................................................................................................................4
2.2. Remote Control........................................................................................................................................5
3. Connecting................................................................................................................................7
3.1. System connection diagram ...............................................................................................................7
4. Introduction of tiling tool....................................................................................................10
4.1. Example of steps.................................................................................................................................... 11
5. OSD Menu..............................................................................................................................12
5.1. Navigating the OSD menu using the remote control...................................................... 12
5.2. OSD Menu Overview........................................................................................................................12
6. Input Mode..............................................................................................................................14
7. Cleaning and Troubleshooting.............................................................................................16
7.1. Cleaning ......................................................................................................................................................16
7.2. Troubleshooting...................................................................................................................................... 17
8. TechnicalSpecications........................................................................................................18
1
The user interface is subject to change, Please refer to the actual machine for user interactions.
1. Unpacking and Installation
1.1. Unpacking
• This product is packed with the standard accessories.
• Any other optional accessories will be packed separately.
• Due to the size and weight of this display, it is recommended for two people to move it.
• After opening the box, please verify that all parts mentioned below are included and in good condition.
1.2. Package Contents
Please verify that you received the following items with your package:
• LCD display
• Quick Start
• Remote Control and AAA
Batteries
• Power cord
• HDMI Cable
• RS232 Cable
• RS232+RJ45
• RJ45 Cable
• Wall mount brackets (4pcs) &
screws (20pcs)
• IR Transducer
Power cord
Quick Start
RS232 CableHDMI Cable
RJ45 Cable Wall mount brackets (4pcs)
& screws (20pcs)
RS232+RJ45
IR Transducer
OK
HDMI
SETTING
VOL
RETURNHELP
INFOOPTIONS
SOURCE
FORMAT
FUNCTION
SPLICE
DIVIDE
Remote Control
and AAA Batteries
NOTES:
• For all other regions, apply a power cord that conforms to the AC voltage of the power outlet that complies with
the safety regulations of the particular country.
1.3. Installation Notes
• Due to the high power consumption, always use the plug exclusively designed for this product. If an extended line is
required, please consult your service agent.
• The product should be installed on a at surface to avoid tipping. The distance between the back of the product
and the wall should be maintained for proper ventilation.Avoid installing the product in the kitchen, bathroom or
any other places with high humidity to avoid shortening the service life of the electronic components.
• The product can normally operate only under 3000m in altitude.
2
1.4. Operating Instructions of wall mount brackets
1.4.1. Operating Instructions of wall mount brackets
1. Clean the table and lay a soft cloth on a table, then beneath the screen surface so as not to scratch the screen face.
2. Refer to below graphic, tighten the screws.
Wall mount bracket
Lock 3 M6 horizontal screws when horizontal
hanging.
Lock 3 M6 vertical screws
when vertical hanging.
3. After tightening the screws, the display can be hung on the wall or spliced on the support.
Mounting in horizontal position Mounting in vertical position
wall mount brackets wall mount brackets
Splicing bracket
Splicing bracket
Splicing bracket
Splicing bracket
3
1.4.2. Mounting in Portrait Position
When using the splicing unit for mounting in portrait position, turn the unit clockwise to move the left side to the top.
This ensures good ventilation and extends the service life of splicing units.
4
2. Parts and Functions
2.1. Input/Output
13 5 6 7 8 9
4
2
1AC IN
AC power input.
2MAIN POWER SWITCH
Switch the main power on/off.
3USB PORT
Used for software update function and multimedia play function.
4RS232 / IR IN / 5RS232 / IR OUT
RS232 / IR network input / output for the loop-through function.
6HDMI IN
HDMI intput.
7DVI IN
DVI-D video input.
8VGA IN (D-Sub)
VGA video input.
9IR IN
IR signal input for the loop-through function.
Note:
• This display’s remote control sensor will stop working if the jack [IR IN] is connected.
5
2.2. Remote Control
2.2.1. General functions
OK
HDMI
SETTING
VOL
RETURNHELP
INFOOPTIONS
SOURC E
FORMAT
FUNCTION
SPLICE
DIVIDE
1
2
9
21
20
3
6
10 11
5
8
7
22
15
14
16 19
12
17
13
4
18
1[ ] POWER button
Turn the display on or put the display to standby.
Long press POWER button until power off.
2[PLAY] buttons
Control playback of media les.
3[USB] button
Go to USB source.
4[CMS] button
Go to Cloud CMS app.
5[HDMI] button
Go to HDMI source.
6[ ] FORMAT button
Reserved.
7[ ] HOME button
Go to Android Launcher rst widgets.
8FUNCTION button
Reserved.
9[ ] [ ] [ ] [ ] COLOR
buttons
Reserved.
10 [ ] Source Button
Choose input source.
11 [ ] Settings Button
Access the OSD menu.
12 [ ] [ ] [ ] [ ]NAVIGATION buttons
Up, down, left and right operation key.
13 [OK] button
Conrm an entry or selection.
14 [ ] INFO button
Show Information OSD.
15 [ ] OPTIONS button
Access currently available options, for Media Input/
PDF Player/Cloud CMS.
16 [ ] [ ] VOLUME button
Adjust volume level.
This manual suits for next models
1
Table of contents
Other AOC Monitor manuals
