ANTUNER AT-100M Instruction manual
Model Name AT-100M
Support Radio Any Radio
Support Antenna Any Antenna
Frequency Range 1-30Mhz
Power Range ★1-18Mhz or SSB/CW 0.1W-100W
★18-30Mhz or FM/AM/FT8 0.1W-50W
Physical Size 139mm x 74mm x 29mm
Weight 370g
Maximum Power Max 3W
Charging Type-C USB 5v/1A(Support overcharge and overdischarge protection)
Battery Capacity 3300mAh
Shutdown Current About 15μA
Stand-by Current About 13mA,about stand-by 150-200 hours(no tuning status)
Tuning Standby Start 1-3 relays need current 130-330mA,about stand-by 10-25 hours.
Charging Time Fully charge about 4 hours.
The LED indicator light is red when charging,green when fully charged.
Notice
1. Antenna feeder system: A good antenna feeder system can improve the tuning success rate and avoid
abnormalities during normal power transmission after tuning;
2. Power supply instructions: Ensure that the device has sufficient power. It is recommended that the
battery voltage is not lower than 3.6V. If the voltage is too low, the device will restart or shut down;
3. Radio type: The factory default radio type is 100W, in order to bring you good power accuracy and
functional experience, please adjust according to the maximum output power of your radio [FIX RADIO];
4. Equipment calibration: The power and standing wave value algorithm of the tuner has been calibrated
when the tuner leaves the factory. But in order to ensure the accuracy, please recalibrate the [FIX PWR] and
[FIX SWR] parameters after changing the use environment, antenna feeder, and radio. Please refer to the
station.
5. Start tuning: Please fully confirm the transmission power, frequency, and mode of your radio before
starting to tune, so as not to damage the equipment.
6. Communication operation: During the normal communication process, please always pay attention to
the standing wave and power of your radio station. If there is any abnormality, please stop transmitting in
time and check before operating.
ANTUNER
Quick Start Manual
Properties
1.First,please connect the radio and antenna respectively.
2.The radio station is set to the frequency range supported by the device, the minimum output power, and
the working mode is FM, AM, CW or SSB.
3.Long press the [TUNE] button to achieve tuning or give up tuning, or when the swr exceeds the set value
when operating the radio, automatic tuning will also be triggered.
4.Operate the radio station to keep transmitting, at this time, the device will automatically tune to the
lowest standing wave and then stop automatically.
5.When the screen shows [SWR] value is 1.0-2.0, the tuning is successful.
6.Set the radio power to the maximum transmission power, frequency, and mode supported by the device
to make a call.
Tuning
Function Menu Range Suggest Introduce
1
Buzzer ★BEEP ON NO/YES YES Push button or standing wave alarm
2
User Store USER COUNT 0-9 0 User defined memory count
3
★TUNE AUTO NO/YES YES
Automatically tunes when the VSWR is too
high
4
★TUNE COUNT 1-20 8
Number of tuned results automatically
stored
5
★TUNE
AUTOSWR
1.00-2.50 1.80-2.0
The standing VSWR auto-tunes beyond this
value
6
TUNE
STOPSWR
1.00-2.50 1.10
Stop Tuning until the tuning result is lower
than this value
7
TUNE DELAY 10-80 32-40 Wait for operating time of the relay(ms)
8
★TUNE SETP 1-8 2-4 Tuning step depth, swr will be lowe
9
★TUNE MIN
ADC
5-50 30
Start tuning voltage value(15≈0.1W,50≈
5.0W),QRP need attention
10
FIX RADIO 100W/10W 100W
Set max power of your radio,QRP need
attention
11
FIX PWR 60%-150% 100% Calibration power
12
FIX SWR 60%-150% 100% Calibration swr
13
★FIX AVG 1-10 3-6 Average value times of power and swr
14
Relay SWITCH ON NO/YES NO
Relay default switching state and affect
electricity
15
TEST RELAY ENTER Test relay failure
16
TEST ADC ENTER Test radio signal power
17
Reset RESET ENTER Reset System all value
Test
★You'll be tweaking these parameters often and are very useful for tuning.
★[TUNE MIN ADC] is signal efficient acquisition voltage when auto-tuning is started.Too low
will cause the induced voltage to be too sensitive.It is recommended to set more than "30".QRP
users need to adjust this parameter.Refer to [TEST ADC]-[FWD] setting.
Advanced Configuration
Enter Advanced Function
ANTUNER
Turned off, press and hold the [TUNE] button, and then turn on.
Tuning
Parameters
Calibration
Other manuals for AT-100M
1
Other ANTUNER Tuner manuals
Popular Tuner manuals by other brands
MFJ
MFJ MFJ-928 instruction manual
NAD
NAD C 445 owner's manual
Sony
Sony ST-SA5ES operating instructions
Sirius Satellite Radio
Sirius Satellite Radio SC-FM1 user guide
Antique Automobile Radio
Antique Automobile Radio 283501B Installation and operating instructions
Monacor
Monacor PA-1200R instruction manual
