Anritsu CMA50 User manual

Part No.: 41315I

CMA50

Operation Manual

Eighth Edition

ANRITSU CORPORATION

For safety and warning information, please read this

manual before attempting to use the equipment.

Keep this manual with the equipment.

CMA50 Operation Manual ii

26 June 2006 (First Edition)

6 July 2010 (Eighth Edition)

The contents of this manual may be changed without prior notice.

Composed in the USA, and printed in Japan.

Notice to U.S. Government End Users

The Software and Documentation are “Commercial Items,” as that term is defined at 48 C.F.R. 2.101, consisting of “Commercial Computer Software”

and “Commercial Computer Software Documentation,” as such terms are used in 48 C.F.R. 12.212 or 48 C.F.R. 227.7202, as applicable. Consistent

with 48 C.F.R. 12.212 or 48 C.F.R. 227.7202-1 through 227.7202-4, as applicable, the Commercial Computer Software and Commercial Computer

Software Documentation are being licensed to the U.S. Government end users (a) only as Commercial Items and (b) with only those rights as are

granted to all other end users pursuant to the terms and conditions herein. Unpublished rights reserved under the copyright laws of the United States.

•The contents of this manual may be subject to change without prior notice.

•No part of this manual may be reproduced without the prior written permission of the publisher.

Windows is a registered trademark of Microsoft Corporation in the United States and other countries.

iii

Safety Symbols

To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the following safety symbols to indicate safety-

related information. Ensure that you clearly understand the meanings of the symbols BEFORE using the equipment. Some or all of the following

symbols may be used on all Anritsu equipment. In addition, there may be other labels attached to products that are not shown in the diagrams in this

manual.

Symbols used in manual

DANGER This indicates a very dangerous procedure that could result in serious injury or death if not performed properly.

WARNING This indicates a hazardous procedure that could result in serious injury or death if not performed properly.

CAUTION This indicates a hazardous procedure or danger that could result in light-to-severe injury, or loss related to equipment

malfunction, if proper precautions are not taken.

CMA50 Operation Manual iv

Safety Symbols Used on Equipment and in Manual

The following safety symbols are used inside or on the equipment near operation locations to provide information about safety items and operation

precautions. Ensure that you clearly understand the meanings of the symbols and take the necessary precautions BEFORE using the equipment.

This indicates a prohibited operation. The prohibited operation is indicated symbolically

in or near the barred circle.

This indicates an obligatory safety precaution. The obligatory operation is indicated

symbolically in or near the circle.

This indicates a warning or caution. The contents are indicated symbolically in or near the

triangle.

This indicates a note. The contents are described in the box.

These indicate that the marked part should be recycled.

For Safety

DANGER

NEVER touch parts where the label shown on the left is attached. Such parts have high voltages of at least 1kV and there is a

risk of receiving a fatal electric shock.

WARNING

1. ALWAYS refer to the Operation Manual when working near locations at which the alert mark shown on the left is attached.

If the advice in the Operation Manual is not followed there is a risk of personal injury or reduced equipment performance.

The alert mark shown on the left may also be used with other marks and descriptions to indicate other dangers.

CMA50 Operation Manual vi

2. IEC 61010 Standard

The IEC 61010 standard specifies four categories to ensure that an instrument is used only at locations where it is safe to

make measurements. This instrument is designed for measurement category I (CAT I). DO NOT use this instrument at

locations specified as category II, III, or IV as defined below.

Measurement category I (CAT I):

Secondary circuits of a device that is not directly connected to a power outlet.

Measurement category II (CAT II):

Primary circuits of a device that is directly connected to a power outlet, e.g., portable tools or home appliance.

Measurement category III (CAT III):

Primary circuits of a device (fixed equipment) to which power is supplied directly from the distribution panel, and circuits

running from the distribution panel to power outlet.

Measurement category IV (CAT IV):

Building service-line entrance circuits, and circuits running from the service-line entrance to the meter or primary circuit

breaker (distribution panel).

vii

3. Laser radiation warning

•NEVER look directly into the cable connector on the equipment nor into the end of a cable connected to the

equipment. There is a risk of injury if laser radiation enters the eye.

•The Laser Safety label is attached to the equipment for safety. See the help sets for the individual Test Modules for the

type and location of the Laser Safety label for a given test module.

Electrical

Shock 4. To reduce risk of equipment damage, injury, or death, adhere to the following warnings:

•Do not use the CMA50 or its AC charger/adapter if the case of either is cracked or damaged.

•Use the CMA50 only with the AC charger/adapter provided for the CMA50 by Anritsu. Anritsu does not guarantee

the safety and functionality of other power supplies.

•Do not use the CMA50 AC charger/adapter outdoors or in wet environments.

•Make sure that the AC input to the AC charger/adapter is within the voltages indicated on the AC charger/adapter’s

case.

•Do not attempt to service the product in any way other than routine maintenance as described in this manual.

•If power is supplied without earthing the equipment, there is a risk of receiving a severe or fatal electric shock or

causing damage to the internal components.

CMA50 Operation Manual viii

Repair 5. This equipment cannot be repaired by the operator. DO NOT attempt to remove the equipment covers or unit covers or

to disassemble internal components. Only qualified service personnel with a knowledge of electrical fire and shock hazards

should service this equipment. There are high-voltage parts in this equipment presenting a risk of severe injury or fatal

electric shock to untrained personnel. In addition, there is a risk of damage to precision components.

Calibration

6. The performance-guarantee seal verifies the integrity of the equipment. To ensure the continued integrity of the

equipment, only Anritsu service personnel, or service personnel of an Anritsu sales representative, should break this seal to

repair or calibrate the equipment. If the performance-guarantee seal is broken by you or a third party, the performance of

the equipment cannot be guaranteed. Be careful not to break the seal by opening the equipment or unit covers.

Falling Over 7. This equipment should always be positioned in the correct manner. If the cabinet is turned on its side, etc., it will be

unstable and may be damaged if it falls over as a result of receiving a slight mechanical shock.

Always set up the equipment in a position where the power switch can be reached without difficulty.

WARNING

Replacing

Battery

8. When replacing the battery, use the specified battery and insert it with the correct polarity. If the wrong battery is used, or

if the battery is inserted with reversed polarity, there is a risk of explosion causing severe injury or death.

CMA50 Operation Manual x

Battery Fluid 9. DO NOT short the battery terminals and never attempt to disassemble the battery or dispose of it in a fire. If the battery

is damaged by any of these actions, the battery fluid may leak. This fluid is poisonous.

DO NOT touch the battery fluid, ingest it, or get in your eyes. If it is accidentally ingested, spit it out immediately, rinse

your mouth with water and seek medical help. If it enters your eyes accidentally, do not rub your eyes, rinse them with

clean running water and seek medical help. If the liquid gets on your skin or clothes, wash it off carefully and thoroughly.

LCD 10. This instrument uses a Liquid Crystal Display (LCD). DO NOT subject the instrument to excessive force or drop it. If

the LCD is subjected to strong mechanical shock, it may break and liquid may leak.

This liquid is very caustic and poisonous.

DO NOT touch it, ingest it, or get in your eyes. If it is ingested accidentally, spit it out immediately, rinse your mouth

with water and seek medical help. If it enters your eyes accidentally, do not rub your eyes, rinse them with clean running

water and seek medical help. If the liquid gets on your skin or clothes, wash it off carefully and thoroughly.

Other manuals for CMA50

This manual suits for next models

Table of contents

Other Anritsu Test Equipment manuals

Anritsu

Anritsu MS8608A User manual

Anritsu

Anritsu MT8860C User manual

Anritsu

Anritsu MP2110A BERTWave User manual

Anritsu

Anritsu 693 B Series User manual

Anritsu

Anritsu MP8931A User manual

Anritsu

Anritsu MT1000A Network Master Pro User manual

Anritsu

Anritsu BERTWave MP2100B User manual

Anritsu

Anritsu MT1000A Network Master Pro User manual

Anritsu

Anritsu MT9812B User manual

Anritsu

Anritsu MT8870A User manual

Anritsu

Anritsu 3656B W1 User manual

Anritsu

Anritsu OSL Series Use and care manual

Anritsu

Anritsu MN469xC Series User manual

Anritsu

Anritsu MX183000A User manual

Anritsu

Anritsu MG3641A User manual

Anritsu

Anritsu MT9810A User manual

Anritsu

Anritsu 3659 User manual

Anritsu

Anritsu MP1590B-30 User manual

Anritsu

Anritsu MD1230B-26 User manual

Anritsu

Anritsu MT8852A User manual

Anritsu

Anritsu VectorStar MN4690B Series User manual

Anritsu

Anritsu MP1590B User manual

Anritsu

Anritsu AutoCal 36581NNF User manual

Anritsu

Anritsu Site Master S113C User manual

Popular Test Equipment manuals by other brands

SMART

SMART KANAAD SBT XTREME 3G Series user manual

Agilent Technologies

Agilent Technologies BERT Serial Getting started

Agilent Technologies

Agilent Technologies N3280A user guide

Vernier

Vernier Go Direct Voltage manual

Lifeloc

Lifeloc R.A.D.A.R. quick start guide

Fluke

Fluke T5-600 Service information

Mercury

Mercury TSL01 user manual

MAHA

MAHA MBT Series Original operating instructions

Fuji Electric

Fuji Electric P-61 instruction manual

ETC

ETC SealerAtor user manual

Skyfine

Skyfine ETHYWAY V2 user manual

Appion

Appion G5 Twin Operation manual

PCB Piezotronics

PCB Piezotronics 8159-0112A Installation and operating manual

BW Technologies

BW Technologies MicroDock II user manual

Sun Nuclear

Sun Nuclear 1027 user guide

Biomark

Biomark HPR LITE READER user manual

Hioki

Hioki 3169-20 instruction manual

Ashcroft

Ashcroft ATE-100 operating manual