AngelTrax CATV2400 User manual
CATV2400 Wireless Cable
TV System
Set-Up
and
User Manual
Patent Pending (Utility and Design)
Patent Pending
Page:
1. Powering the Transmitter
2. Powering the Receiver
3. Transmitter Setup
4. Receiver Setup / Installing the Remote Batteries
5. Setting up the Remote
6. Connecting You Digital Box
7. Watching Your Digital Channels (Or DVD, etc...)
8. Using Multiple CATV2400 systems
9. Remote Control Setup fro Multiple Systems
1. Watch Cable TV on a remote TV, Computer or other CRT device in
any room or even outside your home within 300’
2. Transmits CATV (Cable TV) signals or signals from other video
devices such as Cameras, DVD Player, VCD, VCR, Satellite Receiver.
3. Transmit range is about 250’ indoors (Estimate)
4. Built-in 433MHz and IR remote gives commands over the transmitter
and receiver separately.
5. Encoded 433MHz remote avoids interference caused by other 433
products.
6. Memory functions enables the devices to remain on the last used TV
channel.
NOTE: Monitor should have RCA input (Composite)
7. FCC/CE Approval
FEATURES:
SPECIFICATIONS:
Transmitter:
Frequency: 2400~2483MHz
Transmitting Power 0dBm(FCC) 10dBm(CE)
No. of Channels 4 (2410,2430,2450,2470)
Video In/Out Cable, Air TV, Composite
Video System NTSC or PAL or SECAM
Remote 433MHz
Power Consumption DC9V, 500mA
Operating Temperature -10C~50C
Weight 260g
Dimensions (WHD) 152x125x35 (mm)
RECEIVER:
Frequency 2400~2483MHz
No. of Channels 4 (2410,2430,2450,2470)
Video Out Composite
Remote 433MHz
Video Output Level 1 Vp-p
Power Consumption DC9V, 500mA
Operating Temperature -10C~50C
Weight 140g
Dimensions (WHD) 117x85x42 (mm)
CONTENTS:
Powering the Transmitter
Connecting Your Cable to the Transmitter
The cable provided by your service provider
Incoming Cable from
Cable Provider
To Main TV Set
or Digital Box
Cable Splitter Transmitter
Attach Antenna
9V DC Input
9V DC Input
START HERE Section 1
1
2
Plug one of the power adapters into your Transmitter and into an
outlet. DO NOT TURN POWER ON YET
Connect the transmitter to your incoming cable outlet supplied by
your cable tv provider. (Use the Cable Splitter if needed)
Press the power button on top of the transmitter. You should see a red
light on the transmitter will iulluminate.
1
3
4
Installation & Setup
Connecting Power to the Receiver
Connecting the receiver to Your TV
Plug one of the power adapters into your
Receiver and into an outlet as shown
below. You will see an LED indicating
the channel the receiver is utilizing.
(This is NOT a TV Channel)
Connect the RCA plugs from your AngelTrax receiver to your remote
TV. Please use special care to match colors from the receiver to the
TV. (Red to Red, Yellow to Yellow, White to White)
9V DC Input
9V DC Input
Rear of
Remote
TV
2
5
Installation & Setup
If you have followed steps 1-4 completely, you have completed the basic
setup and you are ready to start enjoying wireless cable TV provided the
transmitter and receiver are on the same RF channel. If you are NOT
receiving a picture, please perform the following steps, 5 & 6.
Transmitter Setup
Go to the location of the Transmitter. Make
sure the power is on and then select the
desired AngelTrax channel by pushing the
CH button on top of the transmitter. (Any
channel is OK) As long as we select the
same AngelTrax channel on the receiver. (If
you experience interference, try a different
channel) Change the channel on both the
transmitter and receiver. They must always
match to communicate.
Press the power button on top of the
Transmitter. A red light will appear indicat-
ing the channel.
Select the desired channel by pressing the
CH button on top of the transmitter.
(STOP) Now, Make sure you turn your remote TV on
and set it to Video , Input or DVD, Game, etc....) using
the remote control that came with your TV. You should
now see a picture on your TV Screen.
3
Installation & Setup
6
7
Receiver Setup
CATV2400 Remote Control
Go to the location of the Receiver. Make
sure the power is on and then select the
desired RF channel by pushing the CH
button on top of the receiver. (Any chan-
nel is OK)As long as you select the same
RF channel on the transmitter.
Install the batteries in the the rear pocket of the AngelTrax
remote control correctly. Place the battery cover on the
remote.
Press the channel button on top of the
receiver selecting the same RF chan-
nel selected on the transmitter. A red
light will appear indicating the chan-
nel.
Make sure your TV is ON and it is
set to Video, Input 1, AV1, etc...
4
Installation & Setup
Quick Troubleshooting
8Using your Angeltrax Remote to Change TV Channels
After you have installed the batteries, hit the SCAN button on the
AngelTrax remote. This will activate the scan feature on the transmitter.
You should see your TV scanning through 125 channels. Please wait a
few minutes until the system has finished scanning. This may take sev-
eral minutes.
After the system has finished scanning, you
are ready to select the desired channel
using the CH up and down feature.
Hit SCAN on remote
If you receive only channel 5 or channel 6, you are most likely on HRC
cable frequencies. The system comes set to STD. To change to HRC,
hold the FUNC key while pressing the HRC button as shown above.
This will change the system to HRC mode. Now hit the SCAN button
and wait for the system to stop scanning.
If you are still haveing trouble, call us at 1-800-673-1788.
If you experience a high amount of interference, go to http://www.angel-
trax.com/catv2400/interference.asp for a solution or call 1-800-673-1788
for live technical support.
STD
HRC
IRC
5
Advanced Installation & Setup Section 2
1
This section is for customers that would like to use advanced features
of the CATV2400 to transmit their Digital Channels, Cameras, DVD or
VHS movies.
Follow the instruction in
section 1 for basic con-
nection. Then, connect a
set of RCA cables from
the Transmitter to your
Digital Box as shown in
the diagram
Digital Cable Box
Same as Section 1
Digital Cable Box Setup
Note: You can connect any device to the RCA connec-
tors on the back of the transmitter. Such as, Camera,
DVD, VHS, etc...
6
Advanced Installation & Setup Section 2
2Press the AV/TV button on your
remote. This will select the RCA
input that you just connected from
the previous page. To go back to
TV, simply hit the AV/TV button
on your AngelTrax remote again.
Watch Your Digital Channel
Remote Control Function
Power Power On/Off the transmitter
TX. CH Switch 2.4GHz transmitting channels of Tx
RX. CH Switch 2.4GHz receiving channels of Rx
TV/AV Switches TV and Video input on transmitter
FUNC* Sets up an new encoded address of the remote
SCAN Automatically scans all TV channels
CH + - Adds or deletes TV channels
CH+/CH- Switches TV channels in sequence
VOL+/VOL- Turns up or down the output volume
MUTE Silent
DISPLAY Shows OSD status
JUMP Turns back to the previous TV channel
MTS Bilingual system
0~9 Selects a TV channel directly by pressing number keys 7
Advanced Installation & Setup
Use Multiple Systems for 2 or more rooms
Section 3
The CATV2400 is fully capable of operating in multiple
locations in the same home, on the same cable system
and still being completely independent of each other and
all other TVs. Follow the instruction below to connect
multiple systems on the same cable drop.
Transmitter
9V DC Input
Transmitter
9V DC Input
1. Setup the transmitters
on any cable drop as
shown.
2. Set one transmitter to
any channel and set the
other transmitter to a dif-
ferent channel.
3. Setup one of the
remote controls to a dif-
ferent address as
explained on the following
page.
4. Setup the receivers
the same as explained in
section one.
1
8
Other manuals for CATV2400
1
Table of contents
