Andersen System 3 E-Series User manual
9184660 BA-00 04/28/2020
Product Series: E-Series
Product Type: Casement and Awning Windows
System 3 Blinds Installation
Parts Included:
Read these instructions before starting procedure.
For additional information visit www.andersenwindows.com.
For questions call 1-888-888-7020.
Tools and Supplies Needed:
Safety
Glasses
Drill / DriverPhillips
Screwdriver
“Andersen” and all other marks where denoted are trademarks of Andersen Corporation. ©2019 Andersen Corporation. All rights reserved.
(2) Bottom Rail
Support Clips
(1) Lift Cord
Retainer Cleat
(7) #6 x 3/4”
Pan Head Screws
1
Insert bottom rail support clips between bottom glass stop
and glass, 4" from each corner.
4"
· Follow manufacturers’ instructions for hand and power
tools. Always wear safety glasses. Failure to do so could
result in injury, product or property damage.
· Use caution when working at elevated heights and
around window and door openings. Follow the
manufacturers’ instructions for ladders and scaffolding.
Failure to do so could result in injury or death.
· Windows, doors, and installation components can
have sharp edges. Wear protective equipment when
handling. Failure to do so could result in injury.
· Support blind panel at all times until fastened. Failure
to do so could result in blind panel falling out causing
injury, property or product damage.
Blinds must be lowered at least 6” from fully raised
position when opening window. Failure to do so may
result in damage to blinds.
6"Minimum
Children can climb furniture to
reach cords.
Move crib and furniture away.
Shorten cords to prevent reach.
Keep cords separate. Twisted or
knotted cords can create a loop.
Keep all cords out of children’s reach.
Window Blind Cord Can
STRANGLE Your Child
4
2 3
Verify orientation of blind panel. Blind panel tilt control knob will be
located on the lower lock side of window. Set bottom of blind panel
on bottom rail support clips.
Predrill holes, 3/4” deep, through blind panel mounting clips. Fasten
with #6 x 3/4” pan head screws using a Phillips screwdriver.
Center blind panel in window sash.
2
9184660
Lock
Side of
Window
Tilt
Control
Knob
Venting awning and xed
windows will have tilt control
knob located in lower right
hand corner.
Equal distance at each side.
Windows with a unit height less than
or equal to 4’ will have two mounting
clips per side. Windows with a unit
height greater than 4’ will have three
mounting clips per side.
Blind Panel Mounting Clip
▶Proceed to step 5 for windows with insect screens.
▶Proceed to step 8 for windows without insect screens.
Interior
View
5
Unlock and open window. Position insect screen near window opening
7
9
6
Feed plastic tassels of blind cords one at a time through grommet in
insect screen frame.
3
9184660
Position top of insect screen into head stop route. Lift up on lift bar
at bottom of insect screen and position bottom of insect screen into
sill stop route.
Close and lock sash. Check for proper operation. Secure blind cords
to lift cord retainer cleat.
Turn tilt control knob
clockwise to close
blinds. Turn counter-
clockwise to open
blinds.
Apply downward
tension on cords to
raise blinds. Hold
blinds in raised
position by wrapping
cords around the lift
cord retainer cleat.
Unwrap cords from
lift cord retainer cleat
and release tension to
lower blinds.
▶Procedure is complete.
8
Lift cord retainer cleat must be located within 4” of cord inlet to blind
panel and not impede blind panel removal. Predrill hole in extension
jamb or appropriate surface and fasten lift cord retainer cleat using
#6 x 3/4” pan head screw.
4"
Maximum
This page has been intentionally left blank.
Other Andersen Window Blind manuals
Popular Window Blind manuals by other brands
Current
Current E-WAND Installation manual and user's guide
weinor
weinor VertiTex ZipR Maintenance Instructions and Directions for use for the end user
Roto
Roto ZAR M R4/R7 Mounting instructions
SOMFY
SOMFY Movelite WT Series instructions
Acmeda
Acmeda RF400 Series instructions
Motura
Motura Pli_353/3 manual