Amigo DC710 User manual

PRODUCT

LEADER

Developed with

professional truckers

for the highest quality

dash camera!

DC710

amiGO!

dash cam

· DASH CAMERA INSTALL QUICK START GUIDE

· DASHCAM VIEWER SOFTWARE INSTALL

QUICK START GUIDE

· DASH CAMERA USER MANUAL

170° Wide Angle Lens

GPS and G-Sensor

Motion Detection/Always-On

33-hour Loop-Recording*

UP TO

miniTV-Out

UP TO

1296P

REC

Included

in this

Package 32GB

Quick Start Guide/

User Manual

Vehicle Power

Cable

Data/Power

Cable

GPS

Module

Windshield

Plate

Micro Memory

Card Reader

Micro

Memory Card

GPS Viewer

Software (PC/Mac)

Windshield

Suction Cup

Table of Contents

Dash Camera Install Quick Start Guide ..........................................

Dashcam Viewer Software Install Quick Start Guide ....................

Dash Camera User Manual ..............................................................

Micro Memory Card Maintenance ..................................................

Page 4-6

Page 7-8

Page 9-14

Page 15

Questions? Comments? Contact Instant Imaging Corporation (IIC Inc.):

(262) 334-7777 / [email protected]

Product Guarantee and Limitation of Liability

This product is approved by ISO9001:2000 International Quality Standard and certified with FCC, CE and SGS. LIMITATION OF LIABILITY (1-YEAR

WARRANTY): This product will be replaced if defective in assembling or packaging. Except for such replacement this product is sold without

warranty or liability even though defect, damage or loss is caused by negligence or other fault.

Please note this product is for personal use only. The forms of usage should not offend or infringe international or domestic copyright laws and regulations.

All recorded videos should be for personal use only. Please note that using this product for recording of occasions like shows, exhibitions or commercial

activities will infringe others' copyrights or legislation rights.

DASH CAMERA INSTALL QUICK START GUIDE

Windshield plate: Align the camera with the windshield

plate and push into slot; the camera should fit snug in

place. Remove adhesion backer and install the plate and

camera to your vehicle windshield. NOTE: Do not install

camera to your dashboard, the video will record upside

down. Do not place camera blocking driver’s view.

Front of

camera

Windshield plate: Align the camera with the windshield

plate and push into slot; the camera should fit snug in

place. Remove adhesion backer and install the plate and

camera to your vehicle windshield. NOTE: Do not install

camera to your dashboard, the video will record upside

down. Do not place camera blocking driver’s view.

This process can also be replicated with the supplied

Windshield Suction Cup.NOTE: Be sure to remove the

clear, protection backer from the cup before installation.

Do not install suction cup and camera to your dashboard

as the video will record upside down. Do not place camera

blocking driver’s view.

Installation: Camera installation

Windshield

plate

Front of

camera

! IMPORTANT !

TIME ZONE & DATE/TIME SETTINGS

This dash camera is pre-set for -5 Time Zone (Eastern

Standard Time). You must change this setting to your local

Time Zone to accurately record the correct time. If the time

is off, the included Dashcam Viewer software may not work

correctly. To change the Time follow these steps:

Pacific

-8

-7

Mountain

-7

-6

Central

-6

-5

Eastern

-5

-4

US Time Zone

Daylight Saving Time Off

Daylight Saving Time On

Turn the camera on

Press Menu > TimeZone then adjust with the Up and Down

arrows based on the TimeZone table below.

Confirm with the OK button.

Set the date/time: Press Menu > Dash Camera Settings

(gear icon) > Time Setup then adjust the time accordingly.

The GPS module will auto-correct any minor

time errors upon finding a signal.

DC710

amiGO!

dash cam

TV-OUTDATA

Up and Down Rotation: Loosen the bracket nut on the right

side of the bracket then adjust up and down to the appropriate

angle (the maximum is 180). Tighten the bracket nut.

Left and Right Rotation: You can rotate the angle of the

device directly (the maximum angle is 200) without

loosening the bracket nut.

Bracket rotation/angle adjustment: If the recording position is not appropriate, it can be adjusted up, down, left and right.

Right side of

camera Right side of

camera

GPS module:

Insert the GPS module into the left side of the

camera bracket (GPS port) to receive GPS signals. Pull out to

remove, if necessary. This module is required for tracking.

GPS Module: installation, removal

Power cable: Insert the mini data cable into the DC IN port

on the right side of the camera bracket. Insert the car

charger plug into the accessory port in your vehicle.

Vehicle Power Cable: installation, removal

Back of

camera Right side of

camera and

vehicle

accessory

port

Acc

TV-OUTDATA

TV-OUT

DATA

By default, this camera is set up to automatically begin recording upon starting the vehicle. Camera will stop

recording a duration after turning off the vehicle unless plugged into an always-on accessory port, in which case it

will continue recording. For full instructions, please refer to the Dash Camera User Manual.

! IMPORTANT !

CHANGING THE MICRO MEMORY CARD

Your camera is pre-loaded with a Micro Memory Card. The card has been pre-formatted to optimize performance on the

dash camera; NO FORMATTING IS NECESSARY WITH THE PRE-INSTALLED CARD. If you choose to replace the

pre-installed Micro Memory Card with a different card, always use a High Speed 10 card and follow these steps:

Installation: Micro Memory Card installation

! IMPORTANT !

If using a new card,

format the Micro Memory

Card before use.*

Back of card faces

back of camera.

Bottom of

camera

Verify that the camera is OFF. Installing a Micro Memory

Card with the power on may damage the card, the dash

camera or both.

The card can only go in one way; the back of the card

faces the back of the camera.

Additional information about

Micro Memory Card maintenance

can be found on Page 15.

Gently push Micro Memory Card into the slot at the

bottom of the camera until it clicks.

Format the card. Turn the camera on, press Menu >

Settings >Format.

Plugging your dash cam into a PC or Mac data port and pressing the Power Button on the camera will open the Removable Disk drive; this is the

dash camera’s memory card. If this box does not automatically appear you may have to go to the Start Menu and then to the PC icon (Windows).

Click the Removable Drive. Choose the HDPlayer folder from the selections and then the setup file that applies to your Operating System

(Viewer32 (Win), Viewer64 (Win) or .dmg (Mac)) If you are unsure of which version of Windows you may have, choose Viewer32.

Your dash camera is pre-loaded with Dashcam Viewer software that allows you to watch video footage, track your route and more on your

computer. See below for full installation instructions (Windows or Mac). Recommended system requirements: Windows 10, 64-bit, i7

processor, Nvidia or AMD video adapter. Windows 7, 8, 10 or Mac OS X 10.8.5 or higher Compatible.

Clicking Setup prompts you with the

Setup Wizard. You may need Admin

privileges to install. Click Next.

The Setup Wizard will automatically

choose the location to install. You may

change this if necessary. Click Next.

Click Install to confirm your program

install location. Click Back to make

changes.

DASHCAM VIEWER SOFTWARE INSTALL QUICK START GUIDE

Dashcam Viewer’s icon should be found

on your desktop. Double-click to Start.

Wait for the program to install to your PC

or Mac. Depending on your setup, this

may take a minute or two.

The Setup Wizard is complete and the

program has been installed. You should not

need to restart your computer. Click Finish.

Wait for the files to Process; this will take a few

minutes based on number/quality of files. A

progress bar will indicate when the files are

ready. When done, the first file will begin to play.

You may add Windows for Data, Graph

and Map and change the size of your

viewscreen boxes. Click the upper-left

icon to Open Movie Folder.

Find the Removable Drive and select the

NORMAL folder. If you have moved the files

from the dash cam to your computer, locate

the folder in which the files are located.

For full Dashcam Viewer instructions, please refer to the e-manual located in the Dashcam Viewer installation folder on your PC/Mac or

go to Help > User Manual in the Dashcam Viewer program. (E-manual reader program is required - not included.) For technical questions

about the amiGO! Dash Cam or Dashcam Viewer software, please contact (262) 334-7777 or email info@instantimagingcorp.com.

DASH CAMERA USER MANUAL

Instructions before use

This User Manual will describe the usage of this product in detail and at the same time provide comprehensive information

including operation and specification, etc. Please read the manual carefully and keep it in a safe location for future reference.

PRODUCT DESCRIPTIONS**

1. Menu / Emergency EVENT Button

2. Mode (Video, Photo, Viewing)

3. UP / Mute Microphone

4. DOWN / EV

5. LEFT / LED Light On/Off Button

6. RIGHT / Select

7. Power On/Off

a. Short Press: Power On/Off; press again to turn off the display. (This will NOT power it off.)

b. Long Press (3 sec): Forced Power Off

8. Record / Snapshot / Confirm (OK)

9. GPS Port

10. Red Light Indicator (Charging)

11. Blue Light Indicator (Recording)

12. Green Light Indicator (GPS Signal) - GPS Module required

13. Lens

14. LED Light

15. Data Port/AV Output

16. miniTV-Output

17. Reset Button

18. Micro Memory Card Slot

19. DC IN (Where you connect your Vehicle Power Cable)

** This will be listed in the instructions as PD Icons.

CHECK PRODUCT ACCESSORIES

Please check whether the following accessories are present before use:

32GB Micro Memory Card (High Speed 10) x 1

Micro Memory Card Reader x1

Data/Power Cable x1

GPS Module x1

Vehicle Power Cable (12ft) x1

Windshield Plate x1

Windshield Suction Cup x1

Dash Cam/Dashcam Viewer* Quick Start

Guide/User Manual x1

Dashcam Viewer installed to memory card upon

camera startup

5 6 7 8

Movie Camera Icon: Indicates camera is in Video Recording Mode. Camera Icon: Indicates camera is in Photo Mode.

Battery: Indicates the remaining power for the device. Charge your camera when the power is low. Plug icon shows while

charging and top red LED lights.

Micro Memory Card: Appears on screen when the card is properly inserted. Otherwise, this is represented with an “X”

G-Sensor: The higher the blue color stands, the more sensitive

Motion Detection: This icon shows up only when it is enabled

! Lock: This Icon shows up when collision/vibration occurs and followed by device mandatory file protection (see G-Sensor)

Microphone: Shows up in Video Recording Mode, press the UP/MIC button to turn it On/Off

GPS: External GPS Module required

HDR: When resolution is set to 1920x1080@30P HDR, it appears.

Speed Limit: Preset speed limit (GPS Module required)

ADAS: Only appears when it is enabled

LED: On/Off

EV: Exposure Value, “+” means brighter, “-“ means dimmer

Video Resolution

Loop Recording: 3 Minutes (for the current setting)

Date Stamp

10)

11)

12)

13)

14)

15)

16)

GETTING TO KNOW YOUR DASH CAMERA VIEWSCREEN ICONS:

Back of

camera

15 13

Table of contents

Other Amigo Dashcam manuals

Amigo

Amigo DC711 User manual

Popular Dashcam manuals by other brands

Cansonic

Cansonic UltraDuo Z2 instruction manual

Gazer

Gazer F720 user manual

HP f500g user manual

Xblitz

Xblitz TANGO 4K user manual

Rexing

Rexing M1 user manual

Maka Technologies

Maka Technologies Marbella MXPro user manual

NESA

NESA NRC-80DLM User manual & installation guide

Kaiser Baas

Kaiser Baas R20 user guide

Boyo

Boyo VTM43TC manual

Minolta

Minolta MNCD37 user manual

Thinkware

Thinkware FA10 user manual

Momento

Momento MD-5200 user manual

BlackVue

BlackVue DR590X-1CH manual

HP F300 quick start guide

CammSys

CammSys BlackSys BH-300 manual

Snooper

Snooper DVR-2HD user manual

Lukas

Lukas Q900 user guide

RVS

RVS 450C Product manual installation & instructions