Ametek 420VA User manual
Security II Series
Uninterruptible Power Manager
For use with 420VA, 600VA, 800VA, 1100VA and 1440VA
RoHS Compliant Uninterruptible Power Manager
2A01-00055 Rev G
1.0 - Introduction .................................................................... 5
2.0 - Safety Instructions ......................................................... 6
3.0 - Installation ..................................................................... 10
4.0 - Operation ....................................................................... 16
5.0 - Maintenance .................................................................. 20
6.0 - Specications ................................................................ 25
7.0 - Troubleshooting ............................................................. 45
8.0 - Warranty ........................................................................ 47
TABLE OF CONTENTS
3
A01-00055 Rev G
IMPORTANT NOTICE ON BATTERY WARRANTY
The warranty policy stated in Section 8 is not valid for applications
in which the UPM is regularly and intentionally disconnected from
AC mains power. AMETEK-Powervar’s two year battery warranty
applies only to products that are properly installed and consistently
connected to AC mains power, except during utility outages.
Products regularly and intentionally disconnected from AC mains
power will experience substantially reduced battery life. AMETEK-
Powervar’s standard warranty term does not apply in these cases
and is supplanted by a 90-day warranty from time of shipment from
AMETEK-Powervar. The warranty provided by AMETEK-Powervar
provides for the replacement of the battery or battery systems in
the event that the batteries do not meet performance specications
as determined by AMETEK-Powervar exclusively.
4A01-00055 Rev G
Danger- The danger symbol is used to indicate imminently
hazardous situations, locations, and conditions which, if
not avoided, WILL result in death, serious injury, and/or
severe property damage.
Caution- The caution symbol is used to indicate potentially
hazardous situations and conditions which, if not avoided,
may result in injury. Equipment damage may also occur.
Warning- The warning symbol is used to indicate
potentially hazardous situations and conditions which,
if not avoided, COULD result in serious injury or death.
Severe property damage COULD also occur.
Attention- The attention warning symbol is used to
indicate situations and conditions that can cause operator
injury and/or equipment damage.
Other warning symbols may appear along with the Danger
and Caution symbol and are used to specify special
hazards. These warnings describe particular areas where
special care and/or procedures are required in order to
prevent serious injury and possible death
Electrical warnings- The electrical warning symbol is a
lightning bolt mark enclosed in a triangle. The electrical
warning symbol is used to indicate high voltage locations
and conditions may cause serious injury or death.
Explosion warnings- The explosion warning symbol is
an explosion mark enclosed in a triangle. The explosion
warning symbol is used to indicate locations and conditions
where molten, exploding parts may cause serious injury or
death if the proper precautions are not observed.
Alternating Current
Refer to instruction manual/booklet.
DANGER
CAUTION
WARNING
ATTENTION
5
A01-00055 Rev G
1.0 INTRODUCTION
Thank you for your purchase of the AMETEK-Powervar Security II Series
UPM ( hereafter referred to as “UPM”). AMETEK-Powervar manufactures
two versions of the UPM – a standard version, a medical version listed
to UL60601-1 and cUL C22.2 No. 60601.1. In addition, all models are
compatible with International electrical distribution systems. International
versions are UL listed (Medical listed to IEC60601-1 and EN60601) and
carry the CE Mark. We’ve prepared this document to help familiarize
you with the functions and controls of this product. If, after reviewing
this manual, you have any questions at all, please feel free to contact
our technical support team by phone (1-800-369-7179) or email us at
servicerma@powervar.com
AMETEK-Powervar is a global provider of power management solutions,
headquartered in Waukugan, Illinois, with international sales and
distribution ofces in Swindon, United Kingdom, Toronto Canada,
Mexico City, Mexico and Germany. All AMETEK-Powervar solutions
incorporate a high energy surge diverter, a noise lter and a low
impedance isolation transformer. Together these components prevent
power disturbances from destroying, degrading or disrupting system
operations.
Registering your AMETEK-Powervar Product
Please take a few moments to register your product purchase.
Registration is easy and quick via the product registration page found on
our website at www.powervar.com.
6A01-00055 Rev G
2.0 SAFETY INSTRUCTIONS
IMPORTANT - SAVE THESE INSTRUCTIONS
THIS MANUAL CONTAINS IMPORTANT SAFETY INSTRUCTIONS.
KEEP THIS MANUAL HANDY FOR REFERENCE.
CAUTION
A battery can present a risk of electrical shock. Short-circuit currents
can be extremely high and can create severe burns as well as the risk of
re or explosion from vented gases. Always observe proper precautions.
When replacing batteries, use the same quantity, rating and type of
batteries used by AMETEK-Powervar. The batteries used in this UPM
are sealed lead-acid and are maintenance free. Proper disposal of
batteries is required. Refer to your local codes for disposal of batteries.
UPM Rating Quantity and Battery Rating
420 VA 2 X 21W @ 12 VOLT
600 VA 2 X 34W @ 12 VOLT
800 VA 2 X 34W @ 12 VOLT
1100 VA 4 X 34W @ 12 VOLT
1440 VA 4 X 34W @ 12 VOLT
CAUTION
• This UPM contains voltages which are potentially hazardous. All
repairs should be performed by qualied service personnel.
• To reduce the risk of re, connect only to a circuit provided with
20 amperes maximum branch circuit over-current protection in
accordance with the National Electric Code, ANSI/NFPA 70.
• The UPM has its own internal energy source (battery). The output
receptacles of the UPM may be live even when the UPM is not
connected to an AC Supply.
7
A01-00055 Rev G
Statement of Intended use
The medical UPMs are intended to protect medical, non-medical
computer equipment and medical devices that need battery backup,
surge protection, voltage regulation and line noise ltering in and around
patient care areas. Safe and continuous operation of the UPM depends
partially on the care taken by users. Please observe the following
precautions. Not following these could result in warranty being voided.
NOTE:
• The UPM is intended for stationary use.
• UPM is not intended for patient contact or for installation that will
cause accidental contact of patients.
• Do not use this UPM for life support applications in which a
malfunction or failure of the UPM system could cause failure or
signicantly alter the performance of a life-support device.
• Do not use this UPM near or around ammable gases. Do not use
this UPM within oxygen-enriched atmospheres.
• Do not disassemble the UPM.
• UPM is CLASS 1 equipment.
• Do not attempt to power the UPM from any receptacle except a
properly grounded receptacle that matches the input plug provided
with the UPM.
• Do not place the UPM near water or in environments of excessive
humidity.
• Do not allow liquid or any foreign object to get inside the UPM.
• Do not block air vents on the side of the UPM. Keep a minimum of
3 inches on all sides.
• Do not plug appliances such as hair dryers, fans, heaters, etc. into
the UPM.
• Do not place the UPM under direct sunshine or close to heat
emitting sources (excessively warm temperatures will shorten
battery life).
• This UPM is intended for installation in a temperature controlled,
indoor area free of conductive contaminants.
8A01-00055 Rev G
• The AC power source for the UPM should be conveniently near the
UPM and easily accessible – avoid extension cords or temporary
power strips to power the UPM.
• The total leakage current of the UPM and consumer connected
equipment should not exceed 3.5 mA for non-medical units.
• Not for use in a computer room as dened in the Standard for the
Protection of Electronic Computer/Data Processing Equipment,
ANSI/NFPA 75.
• The socket-outlet shall be installed near the equipment and shall
be easily accessible.
• The battery should be disconnected from the UPM by unplugging
at its quick connectors when maintenance or service work inside
the UPM is necessary.
• Do not dispose of batteries in a re – batteries may explode.
• Do not open or mutilate batteries. Doing so may release electrolyte
or other toxic substances, which may be harmful to the skin, eyes,
or the environment.
A battery can present a risk of electric shock and high short circuit
current. The following precautions should be observed when working
with batteries:
• Remove watches, rings, or any other metal jewelry or objects
which may make contact with the battery.
• Use tools with insulated handles.
FCC Issues
Attention
This UPM has been tested and found to comply with the limits for a
Class A digital devices (Class B compliance optional), pursuant to Part
15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in both residential and
commercial environments.
9
A01-00055 Rev G
This equipment generates, uses and can radiate radio frequency energy
and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio and/or television
reception, which can be determined by turning the UPM equipment on
and off, the user is encouraged to try to correct the interference by one
or more of the following measures:
Relocate the UPM
Relocate the load.
This device complies to Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference and (2) this device must accept interference received,
including interference that may cause undesired operation.
10 A01-00055 Rev G
3.0 INSTALLATION
Inspecting the UPM
If any equipment has been damaged during shipment, keep the shipping
cartons and packing materials for the carrier or place of purchase and le
a claim for shipping damage:
1. File with the carrier within 15 days of receipt of the equipment;
2. Send a copy of the damage claim within 15 days to your service
representative.
NOTE:
Check the battery recharge date on the shipping carton label. If the
date has passed and the batteries were never recharged, do not
use the UPM. Contact your service representative.
This manual suits for next models
4
Table of contents
Languages:
Other Ametek UPS manuals
Ametek
Ametek 387 User manual
Ametek
Ametek Surgex UPS-17202-53R User manual
Ametek
Ametek Powervar Security II Series User manual
Ametek
Ametek Powervar Security Plus II User manual
Ametek
Ametek UPS-I000-OL User manual
Ametek
Ametek SURGEX Security Plus II UPS-42100-85R User manual
Ametek
Ametek Powervar Sinergy III 2kVA User manual
Ametek
Ametek SurgeX UPS-1440-Li-ISO User manual
Ametek
Ametek ABCE702-11R User manual
Ametek
Ametek GUPS 2400A-107 User manual
