American TIM-341 User manual

TIM-341

2-IN-1 WASTE OIL DRAINER AND CHANGER

Superior Technology at an Aﬀordable Price®

WARNING

Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety

rules and other basic safety precautions may result in serious personal injury.

Save these instructions in a safe place and on hand so that they can be read when required. Keep

these instructions to assist in future servicing.

SAFETY PRECAUTIONS

GENERAL SAFETY RULES

WARNING: Read and understand all instructions.

WARNING:

The warnings, cautions, and instructions discussed in this instruction

manual

cannot cover all possible conditions or situations that could occur. It must be understood

the operator that common sense and caution are factors which cannot be built into this

product, but

must be supplied by the operator.

WARNING

• Do not extract caustic or flammable products

• Do not expose the reservoir to any source of heat

• While extracting high temperature oils, keep hands and face protected

• Only use the device for the purpose for which it has been designed

• Do not modify any component of the equipment

• Only use original spare parts

PRODUCT DATA

• Maximum air pressure for suction: 7~8bar/100~115psi

• Maximum air pressure for discharge: 0.5bar/7.5psi

• Suction speed: (oil temperature <90°C, suction tube diameterΦ6mm): 2 lpm/0.5gpm

• Suction tube length: 2000mm/78.7"

• Discharge hose length: 2000mm/78.7"

• Collection bowl capacity: 18L/4.8Gal

• Extension Funnel diameter: 606mm/23.8"

Item No.

Air inlet

Extension funnel

Capacity

TIM-341

1/4" NPT

Yes

90L/24Gal

J (closed)

J(open)

H（closed）

H(open)

I(closed)

I(open)

K(closed)

K(open)

Suction hose

Discharge hose

Air inlet for

discharge

L(open)

L(closed)

ASSEMBLY

P(closed)

P(open)

Air inlet for

suction

Fig.3: Assemble the tube, oil collecting bowl,

filtrating plank and extension funnel.

ASSEMBLY

Fig.1: Assemble the handle(B) and insert the

probe assembly, close the ball valve(H).

Fig.2: Assemble the vacuum gauge(D) and close

the ball valve(J).

(close)

Fig.4: Insert the assembly into the reservoir,

then turn the handwheel(O) clockwise direction

and tighten.

DJ(close)

OPERATION

SUCTION

Fig.5: Close all the valves (K,

J, H, I, L)

. Open the handwheel

(E)

counterclockwise direction

and open the valve(L).

Fig.6: Connect the air supply,

and make the vacuum gauge (F)

index reach the green area.

Fig.7: Connect the probe (S),

then put it into the car engine,

open the ball valve (J) for

evacuating oil.

Fig.8: Close all the valves (K, P, J, H, I, L). Open

the ball valve (P) and the valve (H) .

Fig.9: Place the oil drainer under the car to

collect the waste oil. Open the ball valve(P).

COLLECTING

I (Close)

(Close)

7 bar

AIR

FJ(Open)

P(Open)

H(Open)

(Open)

L (Open)

Problem

The index on vacuum gauge

can’t reach the green area.

The vacuum gauge index reaches

the green area, but oil isn't

evacuated.

The vacuum gauge shows

leakage and can’t suction

the oil.

Cause

1. Air supply pressure is too low.

2. Air flow is not enough.

1. Oil temperature is too low.

2. The suction hose, valve or

fitting is jammed.

1.O-ring of the suction fitting is

broken.

2. The bottom of the suction hose

is higher than the oil level.

Solution

1. Increase the air supply pressure.

2. Enlarge the air inlet diameter,

shorten the hose length.

1. Increase the oil temperature

2. Clean or replace suction hose, valve

or fitting.

1. Change the O-ring.

2. Keep the suction hose straight

and ensure the hose is immersed in

the oil.

TROUBLE SHOOTING GUIDE

CAUTION

• Never fill the reservoir over the maximum level indicated by the gauge that is located on the side

of the reservoir.

• Don’t exceed maximum pressure 0.5bar/7.5psi for draining.

• Air pressure for vacuum is maximum 8bar/115psi.

• Open the bottom nut of the reservoir periodically and clean out any dirt.

DRAINING

Fig.10: Close all the valves (K,

P, J, H, I, L ).

Fig. 11: Close the handwheel

(E) clockwise direction, put the

spout (M) into the waste oil tank,

then open the valve (I).

Fig.12: Connect the air supply,

and open the valve (H) for

draining.

(Close)

I(Open)

(Open)

0.5bar/ 7.5 psi

maximum

0.5bar/ 7.5 psi

maximum

(close)

EXPLODED & PART LIST

Pos. No.

Description

Probe kit

Tool tray

Safety valve 7.5psi

Ball valve 1/4" NPT

Item No.

TIM-340-PRB

TIM-317-24

TIM-340-SFT

TIM-317-43

Item No.

Not available

TIM-317-12

TIM-340-SXN

TIM-340-VAC

Q'ty

Pos. No.

Description

Reservoir

Discharging hose assembly

Suction hose assembly

Vacuum assembly

Q'ty

Tubes:

5mm OD (70cm L) plastic

5mm OD (70cm L) copper

6mm OD (70cm L) plastic

6mm OD (70cm L) copper

7mm OD (100cm L) plastic

8mm OD (70cm L) plastic

Adapters:

BMW Adapter

Mercedes Adapter

Volkswagen Adapter

Q'ty

TIM-340-PRB Probe Assembly

includes the following:

Note: TIM-340-VAC Vacuum Assembly includes: gauge, manifold, valves, muffler, etc.

Note: TIM-340-SXN Suction Assembly includes: hose, valve, coupler, chain, etc.

Mercedes Adapter

BMW Adapter

Volkswagen Adapter

OIL COLLECTING BOWL ASSEMBLY & PART LIST

Pos. No.

1-1

1-2

1-3

1-4

1-5

Description

Tube assembly

Ball valve

Screw

Bowl supporting tube

Oil collecting bowl

Q'ty

Pos. No.

1-6

1-7

1-8

1-9

Description

Filtrating plank

Funnel extender

Rotor

O-ring 2 per pack

Item No.

TIM-341-TUBE

TIM-317-32

TIM-317-34

TIM-317-33

TIM-317-37C

Item No.

TIM-317-38

TIM-FNL-XTND

TIM-317-36

TIM-317-35H

Q'ty

1-2

1-7

1-6

1-5

1-4

1-9

1-3

1-1

1-8

RESERVOIR & PART LIST

Part No.

7-1

7-2

7-3

7-4

7-5

7-6

7-7

Description

Reservoir assembly

Handle

Screw M6*8

Valve 3/4" NPT

Swivel adapter

Caster

Flat washer

Q'ty

Part No.

7-8

7-9

7-10

7-11

7-12

7-13

Description

Spring washer

Nuts

Elbow

Nut

Tube with label

Clip

Item No.

Not available

TIM-317-20

TIM-317-17

TIM-317-11

TIM-317-10

TIM-317-4

TIM-317-5

Item No.

TIM-317-41

TIM-317-6

TIM-317-7

TIM-317-8

TIM-317-9

TIM-317-19

Q'ty

Note: TIM-317-4 Caster bag includes two each of the following: wheels, flat washers, lock washers, nuts.

Note: TIM-317-PLUG (not shown; location - bottom of reservoir) includes drain plug and sealing gasket.

Table of contents

Other American Water Pump manuals

American

American AME0413HD User manual

Popular Water Pump manuals by other brands

Neptun

Neptun NPHW 5500 operating instructions

Sensidyne

Sensidyne Gilian BDX-II Operation & service manual

Draper

Draper 47808 instructions

Trolla

Trolla 12820 manual

Sunfab

Sunfab SVH Series installation guide

WilTec

WilTec 50740 Operation manual

Fieldmann

Fieldmann FVC 5015 EK user manual

Everbilt

Everbilt EFSUB5-122HD Use and care guide

Graco

Graco Husky 3300e manual

esotec

esotec 101018 operating manual

moyno

moyno 2000 CC Service manual

Becker

Becker BASIC VASF 2.80/1-0.AC230 operating instructions

Sykes AmeriPumps

Sykes AmeriPumps GP100M Operation and maintenance instructions

DUROMAX

DUROMAX XP WX Series user manual

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 operating instructions

Franklin Electric

Franklin Electric IPS Installation & operation manual

Xylem

Xylem e-1532 Series instruction manual

Milton Roy

Milton Roy PRIMEROYAL instruction manual