Amerec A6 Club Control User manual

A6 OPERATING INSTRUCTIONS

05/12/16 4211-146 Page 1 of 11

Amerec’s A6 control for the AX steamer

is a touch screen control intended to be mounted on a wall,

generally in or near the steam bath. It may be mounted directly on the wall surface or, using an optional recessed

mounting box, it may be mounted so its touch screen is almost flush with the

wall surface.

Using the A6, you set or adjust the steam bath time and temperature, control

options such as lights and fragrance pumps, and use Warm Start (if installed)

to keep the steamer’s water hot between baths so it produces steam more

quickly when the bath is started. Delayed start and calendar start settings

allow you to have a steam bath ready to use in a few hours or on a regular

schedule. Favorites save your preferred settings for later use. WiFi apps give

you wireless control from your Android phone and iPhone or while using a PC.

You can even prevent the steam room from being used during certain time

periods.

Intelligent steam control learns how long it should take your room to reach a

comfortable steam bath temperature then adds this time to your delayed starts

so you set when you want to start your steam bath and the bath will be up to

temperature and ready when you are.

You may use 1 to 3 controls with an AX steamer, including 1 or 2 A6 controls + an A3.

To reduce the risk of damage to the steamer or controls and to ensure the controls connect properly with the

steamer, always turn power off to the steamer before connecting or disconnect a control.

Index

Section Page

Navigation 2

Turning Things On and Off 2

Start Up 3

Initial Set Up – Tools Menus 4

General 4

Limits 5

Additional Settings 5

System 5

Options 6

Favorites 7

WiFi 8

Apps 8

Available Languages in the A6 9

Warm Start: Is It Installed? 9

Mounting the Control 10

Recessed Mounting Template 11

For further assistance, contact

P.O. Box 2258, Woodinville, WA 98072

Phone 1-800-363-0251

1-425-951-1120

Fax 1-425-951-1130

eMail [email protected]

A6 OPERATING INSTRUCTIONS

05/12/16 4211-146 Page 2 of 11

Navigating the A6

Some indicators are used while navigating and setting the control. These are blue when their screen or menus

are in view, gray when they are not in use.

The Home button: touch this to return to the main screen. Here you will see the current temperature in

the steam room, the bath temperature setting, the remaining bath time (if any) and the time of day.

Touch the screen to show the bath and Warm Start on/off buttons, too.

The Settings button: touch this to display the Settings screen. Here you can adjust the temperature and

duration for the current bath. You can also manually turn on the installed options when the bath is on

(and turn on some options, such as Lights, when the bath is off). You can also save your settings as a

favorite so you can always have them available for your steam bath without having to change settings after

someone else has a steam bath.

The Favorites button: Here you can select a bath with your favorite settings, once you’ve saved it.

The Calendar button: Here you schedule a steam bath to start and run at a later time. You can select by

the day of the week or using a calendar month and select for one time bath or recurring.

The Tool button: here you make the many selections for what functions and options are available to be

used, set a PIN to limit who can change settings, and much more.

The Change Menu arrows are used to move between related menu screens. Press to return to the previous

screen or to continue to the next one.

Turning Things On and Off

The Bath On/Off indicator bar shows at the top of the home screen. Note: if it isn’t visible, simply touch the screen

to see it again. Touch the right side to turn the bath on, the center to start Warm Start (if installed) and the left to

turn the bath or Warm Start off.

Bath Off Bath On

Bath and Warm Start Off Bath On

Bath Off, Warm Start ON

The slider switches are moved to turn something on or off.

OFF ON

The Cancel and Accept buttons are used after making some changes. Press to accept your changes, press

to cancel any changes.

A6 OPERATING INSTRUCTIONS

05/12/16 4211-146 Page 3 of 11

Start Up

The first time your A6 is turned on, it will need some information loaded and some settings changed.

When the power is first turned on, the steamer will take about 30 seconds to start operating before the A6 is

turned on. The A6 screen will then light and display the amerec logo, then change to a lit screen with spinning

circle showing while it loads its own software. This will take 1-1/2 minutes with one steamer and one A6. Multiple

steamers or multiple controls can make everything take a little longer while all the software loads.

The first thing you will see is the Welcome screen. Now press the Change Menu button to move to the Language

selection menu and select your language, then to the Region menu and select North America, then to the Date

Format menu, and then set the current date. Next set the Time format, then the current time.Now change menus

again and you will see the Home screen. (Note: page 9 for a list of all available languages.)

Note: at this point, the room temperature may not be accurate yet. As the A6 measures the actual temperature,

the display will increase until the correct temperature is reached. After this the temperature display will change

quickly, as expected.

Press the > to set the time.

When the time is set,

press > again

to finish the set-up and

go to the home screen.

A6 OPERATING INSTRUCTIONS

05/12/16 4211-146 Page 4 of 11

Initial Set-up

Once you are ready to use your A6, there are a few things you need to set up. You’ll want to set the normal bath

time, the bath temperature, set the temperature readings for °C or °F, turn a few options on or off, and maybe set

an access code. Some functions may have already been set up by the installer, but we will assume only the initial

start-up has been done.

First, go to the Tools menu by pressing its button. You will start in the General menus section.

You should have already language, region, set time and date so next choose the

temperature Units setting by touching its

Touch to select Celsius (°C) or Fahrenheit (°F) to be

used for your temperature displays then press the

button to return to the Tools menu.

Next set the Display time out delay. This setting determines

how long the control’s display is lit before blacking out. The

Display time is set to minutes by default.

Select the time you want the use to return to the Tools

menu.

Do you want to use a PIN code to prevent others from

changing (or seeing) some of the control’s functions? If not,

skip to the next setting.

To create a PIN number, select PIN. Touch the Activate slider to turn the PIN on

and choose which functions you would like to have available to anyone without using the PIN code. In the settings

below, anyone can start or stop the bath and adjust the room temperature but they cannot control the room light

or make any other changes.

You may have other options available

on the PIN screen depending on how

your system is set up and which options

are installed.

Now select Change PIN to go to the

PIN screen (at right). Enter the current

code (0000 by default). Then select

to accept the entry.

Next, you’ll enter the new code, select

, then reenter the new code and

press again and you will see a note

that the new code is accepted before

you return to the previous screen

If you change your mind or want to cancel the new PIN code before accepting it, press

Next we’ll set some system limits.

Now u

se to return to the Tool menu screen, then slide your finger down the screen to scroll further down to the

Limits section.

A6 OPERATING INSTRUCTIONS

05/12/16 4211-146 Page 5 of 11

Warm Start On

Limits menus

To set the maximum allowed bath temperature, select Bath temperature. This lets you

limit the temperature anyone can set the bath to (no more than 125°F by default). For

instance, if you have someone in the family who is sensitive to heat, you may set the

limit to 115°F so they cannot accidentally set the bath too hot. They can still adjust the

bath temperature, just with a lower maximum setting.

If you want to prevent the steam bath from being used during certain hours, say during

the day while you’re not at home or from 10:00 pm to 7:00 am for a hotel’s quiet time,

use the Not allowed start setting to set the time period.

If you have water problems which might prevent you from having water available for the

steamer, set the Max water fill time to a reasonable time limit. If water pressure is too

low, you may need a longer time. If your water supply is normally good, you may be

able to set it to 2 or 3 minutes. Default is 6 minutes.

If it takes longer than the fill time setting to reach normal operating levels in the steam, the system will

show you an error and shut down to prevent damage to the steamer. And remember, you must have at

least 20 psi (138 kPa) water pressure for proper operation.

Additional settings menus

Warm Start is an option which keeps the water in the steam tank warm so the steamer

produces steam more quickly after the bath is turned on. If you do not have Warm Start

installed, select warm start and move the slider to disable it.

If Warm Start is installed, you may adjust the temperature up from the 176°F default to

speed up steam production even more. If you do turn up the Warm Start temperature,

watch for steam from the steam outlet while the bath is off. If you see steam while only

Warm Start is running, turn down the temperature a few degrees and repeat until the

steaming stops.

If you have a vent fan connected to the steamer’s FAN option terminal block, select Fan

to set up how it will operate. Turn on Automatic to have the fan run after the bath. The

fan will run 20 minutes by default but may be set from 1 minute to 3 hours by changing

the Running Time setting. The fan may also be turned on or off manually while in this

menu.

Next scroll down further for the System menu section.

System menus

Options and WiFi will be covered in their own sections.

Use the Cleanup note settings to turn on/off a reminder which tells you when it is time

to clean the tanks, such as for decalcification when you have hard water. You can also

set the number of operating hours before the reminder appears.

In this menu, you also can choose to see reminders that the tank should be emptied

after a bath. If you do not have an automatic electronic drain valve, you should drain

the tank periodically to keep it clean. How often depends on you water quality. If you

cannot get to your steamer’s manual drain valve easily, we recommended turning off

the Tank Empty Notes so you don’t see the reminders.

The rest of this menu is for service use and should be left as is.

Options

Warm Start Off

A6 OPERATING INSTRUCTIONS

05/12/16 4211-146 Page 6 of 11

Go to Options to set up various options available for use with you steamer.

Your AX steamer comes with two options automatically

loaded: a room light which always light during the steam

bath and remains on for 10 minutes after the bath stops (or

can be manually turned on and off) and a dedicated fan

control (set-up previously in the Systems menus).

You also have connections for three additional options of

your choice, AUX 0, AUX 1 and AUX 2. These options use

a relay in the steamer as a switch connected to the Options

terminal block.

To add an option, select Options then select one of the Aux

items. Below, we’ll set Aux 0 for controlling Chromatherapy

lights.

In Aux 0’s menu, select the blank white block so you can name your option and the

keyboard will appear. Enter the name for your option then press the to accept the

name. The name can have up to 15 characters maximum (longer names may not

display properly).

Now select On/Off for the operation

needed then return to the options

menu.

A Fragrance option may be connect-

ed to inject aromatic oils into the

steam bath. If you wish to connect a

Fragrance system, set an AUX to

Fragrance and name the option.

If you need to set the pump timing for more or less fragrance,

use the fragrance menu to select how long the Pump injects the

aroma oil and how long the pump Stops between injections. Start

with the default settings and adjust for more or less fragrance as you get use to the effects. You do not want too

much fragrance, so start with a little and work your way up as needed

Now go to the Settings screen and you’ll see the

options added to the screen. When you start a bath,

Lighting will automatically turn on but the options will remain

off until you turn them on manually.

When the bath turns off, the options will be turned off automatically, too.

A6 OPERATING INSTRUCTIONS

05/12/16 4211-146 Page 7 of 11

Favorites

When you finish your steam bath, the bath settings will be saved for the next bath automatically. If the next user

makes changes, the following bath will use the new settings.

You can save your bath settings as a favorite so you can always have the settings you

want. This will save the bath temperature and time and the options you want turned on

for you bath. The A6 will let you save a total of eight favorites

When you have your bath set up the way you like it, go to the Settings screen

then select Save as favorite.

Now you will go to the Keyboard where you can type in the name of your favorite set

up. The name can have up to 15 characters maximum (longer names may not display

properly).Select when done and you will be returned to the Settings screen.

To use your saved favorite, go to the Favorites screen.

You will see list of all the saved favorites settings. Select

your favorite and the Settings screen will appear with all

your favorite’s settings in place. Make any changes you

may want, then select Start to begin your bath.

If you decide to delete a favorite, go to the Favorites

screen and select that entry. When it returns you to the

Settings screen, there will be a small trashcan in the upper

right corner.

Select the trashcan to delete that favorite.

You will be asked to accept deleting that

favorite, then you will be returned to

the Favorites screen.

A6 OPERATING INSTRUCTIONS

05/12/16 4211-146 Page 8 of 11

WiFi

If you plan on using an app with your steam system, you will need to enable the WiFi

connection first. Select WiFi on the Systems menu to go to the WiFi menus.

Use the slider switch to Enable WiFi.

Next select Network.

Now set the slider switch to Auto connect.

Next select Scan. A list of available WiFi networks should appear. Select your network

and on the next screen, select and enter your password for the WiFi network. Select

to accept the password and return to the network screen.

Now select Connect. A couple messages will appear showing that the connection is

being made and has been accepted. Press OK to clear the messages.

Now return to the network scan screen and enter a name for you bath system: you will use this to help connect

with your app(s). Select the blank white block then use the keyboard to enter the name (15 characters maximum

(longer names may not display properly)) then use to accept the name and return to the previous screen.

Make sure the Auto connect switch is still enabled (green) then return to the previous screen and make sure WiFi

is still enabled. Note: in this screen you can check to see all of the apps and A6 controls which are connected to

your system.

Now return to Tools then Home.

APPs

The AmerecConnect app is available free from the iTunes Store for iPhones and iPads and from Google Play for

Android phones. An app is also available for PC computers (contact Support to obtain the PC app). Apps are not

yet available for Windows phones or Macintosh computers. Android phones must be version 4.0 or higher.

The apps look and operate identically to the A6 control.

To connect an app to the system, it must be connected to the same WiFi network and to the steamer system. You

will need to log in to the WiFi network first. Then, in the app, go to Tools then Network then set Auto connect on

(green). Select Find System. Your steam bath system name should be listed. Next select your system then select

Connect. Select Change PIN and enter the PIN code (0000 by default or the number sour changed it to). then

enter the PIN code to. Save the PIN code. Now select Connect. A short time later Connect will change to

Disconnect, indicating you are connected to the steam system. If you ever want to disconnect from the system, go

here and select Disconnect.

Return to the Network screen and make sure the auto connect slider switch is on. You should see your system

name on the screen with a check mark in front of it. If you ever see the system name in parenthesis, it means you

are disconnected.

The apps have fewer Tools available than the A6. There are risks when starting a bath while using a phone: you

may not be near enough to know if something has changed at the room, such as the door being left open, so the

selections are reduced for safety.

The PC app has many more selections available, assuming that with a PC you are more likely to be near enough

to the bath to be aware of changes. This is intended especially for use in light commercial areas, such as a spa.

A6 OPERATING INSTRUCTIONS

05/12/16 4211-146 Page 9 of 11

Available Languages in the A6

Czech

Danish

German

English

Spanish

Dutch

Norwegian

Polish

Portuguese

Russian

Slavic

Finnish

Swedish

Warm Start: Is It Installed?

If you enable Warm Start on the A6 and you get a

steam tank temperature error when you try to turn on

Warm Start for the first time (see

Turning Things On

and Off

on page 2), you’ll need to remove the cover

from your steamer and see if the Warm Start option

is installed.

If warm start is installed, you’ll see a temperature

sensor on the side of the steam tank which connects

through a tube to the steamer’s circuit board.

If Warm Start is installed and you still get a sensor

error, first make sure the sensor is connected to both

pins on the steamer board (between the cable jacks

and the level probe wires). If it is connected, contact

Support for further assistance.

A6 OPERATING INSTRUCTIONS

05/12/16 4211-146 Page 10 of 11

Mounting the Control

Surface mount the A6 control inside or outside the steam room using the control

cable installed in section 5, step 4. If mounting to a smooth, flat wall, the adhesive pad

provided will work well to mount the control and seal the cable hole. The adhesive will

stick to the wall quickly so be sure to accurately place and level the control before

attaching it to the wall!

If the surface is uneven or has grout lines, we recommend using a small amount of

silicone to mount the A6 control. If using silicone, run a bead around the control’s

cable end and another bead around the back of the control as shown here. Then tape

in place on the wall until the silicone has set up.

Note: A cut mark on the back indicates the top of the control

The control’s cable end is at the bottom of the control.

Be sure to carefully level the control while mounting!

Recessed Mounting

The recessed mounting box allows the A6 to mount with its surface almost even to the wall surface.

You’ll need to cut a hole in the wall to match the

back of the mounting box and run the control

cable out of the wall through the hole in the

mounting box. Make sure the hole is just big

enough to mount the box – you need room

to add silicone to seal the box to the wall.

Next run a bead of silicone around the back

of the box’s front lip, then press the box into

the hole and turn the mounting screws to pull

the tab tight against the inside of the wall.

Make sure the box is level and the correct

end is UP (there is an arrow on the wall side

of the box pointing up).

When the box is ready, run the A6’s cable end

through the cut-out in the adhesive and attach

the adhesive pad to the back of the A6. Be careful – the adhesive will stick quickly.

Now connect the A6 cable end to the control cable then feed the cables and connector through the hole in the box

and into the wall. Now test the A6 before mounting it into the wall! Once mounted, the A6 will be hard to remove!

When ready, peel the cover off the back of the adhesive and carefully push the control into the box and hold in

place for about 30 seconds to finish mounting the control. Press the trim ring on to the front of the box and control.

Snap it in place top and bottom and along both sides.

SILICONE

ADHESIVE OR

PLATED COVER RING

ADHESIVEPAD

MOUNTINGBOX

L

Table of contents

Other Amerec Control Unit manuals

Amerec

Amerec PURE 2.0 User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual